• Korea-Australia Rheology Journal
• /
• 제15권1호
• /
• pp.35-41
• /
• 2003

It is expected that particle size distribution of any portion obtained through screening, is of more uniform than that of the original mixture, typically following such as log-normal, Rosin-Rammler distributions and so on. In this study, therefore, a new relation between parameters of the uniform distribution and flow characteristics of the coarse particle suspensions is derived based on the continuous polydisperse model (Ookawara and Ogawa, 2002b), which is derived from the discrete polydisperse model (Ookawara and Ogawa,2002a). The derived model equation predicts a linear increase of viscosity with shear rate, viz., dilutant flow characteristics. Further, the increase of viscosity is expected to be proportional to the square of volume fraction of particles, and to show the linear dependency on density and average diameter of particles. It is also shown that the uniform distribution model includes additional term that expresses the effect of distribution width. For verification of the model, the experimental results of Clarke (1967) are cited as well as in our previous work for the monodisperse model (Ookawara and Ogawa,2000) since most parameters were varied independently in his work. It is suggested that the newly introduced term expands the applicable range compared with the monodisperse model.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.5-10
• /
• 2006

The purpose of this study is to measure the droplet distribution and Sauter mean diameter(SMD) of biodiesel fuel, using the immersion sampling method. This method involves using an optical microscope and a CCD camera, to take an image of the droplets. These images are then measured by using a 'Sigma Scan' processing program. The results of the above experiment are summarized as followed ; (1) There can be as much as a 10% error rate when measuring the diameter of these droplets, using the image processing method and the naked eye. (2) The result of droplet size distribution test, TVO(transesterified vegetable oil) big size droplet distribution were increased at ambient pressure $6kg/cm^2$. (3) When ambient pressure increased $6kg/cm^2$ above, SMD variation of TVO and UVO(used vegetable oil) 30 are small. (4) On Rosin-Rammler analysis, droplets size distribution of UVO(used vegetable oil) 30 uniform more than TVO 20 on ambient pressure $1kg/cm^2$.

• 한국안전학회지
• /
• 제32권4호
• /
• pp.16-21
• /
• 2017

The sprinkler system is a basic fire extinguishing system that uses water as an extinguishing agent. In order to evaluate the fire extinguishing performance of the sprinkler system, information such as the discharge angle, discharge speed, discharge pressure, flow rate, and water droplet size of the installed head are required. However, there is a lack of research on droplets size compared to other requirements. In this study, to evaluate the extinguishing characteristics of sprinkler system, the droplet size distribution was measured for various types of sprinkler heads actually used. The size of the droplet was measured using laser diffraction method. The 50% cumulative volume distribution ($D_{v50}$) according to discharge coefficient(K factor) was $540{\mu}m{\sim}695{\mu}m$ for K50, $542{\mu}m{\sim}1,192{\mu}m$ for K80, $980{\mu}m{\sim}1,223{\mu}m$ for K115 and $1,188{\mu}m{\sim}1,234{\mu}m$ for K202. Based on the measured results, the vaeiance of the droplet particle distribution and the distribution ($D_{v50}$) according to discharge coefficient(K factor) was $540{\mu}m{\sim}695{\mu}m$ for K50, $542{\mu}m{\sim}1,192{\mu}m$ for K80, $980{\mu}m{\sim}1,223{\mu}m$ for K115 and $1,188{\mu}m{\sim}1,234{\mu}m$ for K202. Based on the measured results, the vaeiance of the droplet particle distribution and the Rosin-Rammler index value are presented. As a result of the fire simulation with FDS, it was confirmed that the performance difference occurs according to the water droplet size distribution even when the same amount of water is used. Therefore, the extinguishing performance of the sprinkler system should be evaluated considering the droplet size distribution according to the sprinkler head type.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 춘계 학술대회논문집
• /
• pp.190-195
• /
• 2004

The pressure drop in a Venturi Scrubber is predicted using the Eulerian-Lagrangian Method, which is one of the numerical methods to solve the dispersed two-phase flow. KIVA-3V Code is modified to solve the coupled gas-liquid two-phase flow field. The liquid is assumed to be injected through the nozzles with the Rosin-Rammler drop size distribution. The computational results shows good agreement with the experimental data.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.338-343
• /
• 2003

Computations were performed to investigate the spray characteristics of the twin fluid nozzle in three stage heavy-oil combustion burner. The burner geometry and flow conditions were provided by a burner company. The goal of the study is to estimate mean droplet size, initial velocity and spread factor of the nozzle through comparison between experiments and numerical analyses. Air stage ratio is 2:4:4 by mass, and O2 in exhaust gas is about 4 % by volume. Here, the agreement between the experiment and numerical analyses is evaluated by NOx generation. Spray characteristics will be linearly interpolated between fuel consumption rate l20L/h and 240 L/h.

• 한국분무공학회지
• /
• 제9권2호
• /
• pp.1-8
• /
• 2004

This work was performed to investigate the distribution of the fuel droplet size around the bluff-body and the combustion characteristics. The geometry of the bluff-body influenced the spray shape and the combustion characteristics. Diameters of the bluff-body in this experiment are 6, 8, and 10 mm and the impingement $angles({\theta})\;are\;30^{\circ},\;60^{\circ},\;and\;90^{\circ}$. The measurement points were at the distances of 20 and 30 mm axially from the nozzle. The SMD and Rosin-Rammler distribution was acquired by image processing technique (PMAS), and the mean temperatures were measured by thermocouple. The results obtained are as follows; In the condition of ${\theta}=60^{\circ}$, the values of SMD are not greatly varied compared to the other conditions. As the impingement angle of bluff-body was increased, the high temperature region was wider along radial direction. When the air-fuel ratio was increased, the CO concentration was decreased.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2004년도 제30회 국제세미나
• /
• pp.19-42
• /
• 2004

Sizing properties in paper are generally developed through the application of both internal and surface sizes. Rosin, wax, and synthetic sizes including ASA, AKD, and stearic anhydride are and have been used to provide wet-end sizing to paper. In many cases, the use of some of these sizes leads to runnability problems that are inherent in the wet-end operation. Variability in furnish, fines, broke, filler, water chemistry, conductivity, and pH control impacts the wet-end operation. Size press chemicals including starch and polymers such as styrene-acrylic, styrene-maleic, and styrene acrylate emulsions are used in conjunction with internal sizes to improve the paper surface for printing and strength properties, porosity, and opacity improvement. This paper will discuss results from a new, proprietary formulation and process that allows application of sizing chemistry more totally at the size press with reduced emphasis on wet end sizing. Runnability issues are thus minimized at the wet-end, chemical usage is more efficient, and significant cost savings can be realized. Case histories will be presented illustrating the advantages of this new application in commercial trials.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.149-156
• /
• 2013

This study examines the effects of limestone's factors on the fluidity of cement paste when of up to 15%. As the substitution ratio of limestone powder increases, the fluidity of the paste is also improved; however, it has no correlation to the $CaCO_3$ content of the limestone, fineness of the limestone, and fluidity of the pastes. Regardless of clay content of the limestone, it showed a similar mini-slump, so there was no correlation between the clay content and the fluidity of the paste. Also, the total organic carbon content of the limestone and the fluidity of the paste showed no correlation. Regardless of the limestone's grade or fineness, n value of powder gained by using the Rosin-Rammler distribution function showed that the fluidity of the paste increased as the n value reduced. It was also shown that particle size distribution of ordinary Portland cement with limestone powder had a major effect on the fluidity of the paste.

• 한국식품영양과학회지
• /
• 제29권1호
• /
• pp.85-92
• /
• 2000

This study was carried out to storage of Pleurotus ostreatus packed in various trays made by different matrials-expanded polystyrene (EPS), rice straw pulp(RP), and RP trays coated with starch, carboxyl methyl cellulose (CMC), polyacrylamide (PAM), alkylketen dimer (AKD), rosin size (RS) and polyethylene glycol (PEG) at 8~1$0^{\circ}C$ and 70~80% relative hymidity for 6 days. At 6 days storage, weight increase of RP and CMC tray was lower (p<0.05) than those of others and the weight of oyster mushroom packed in RP, CMC and AKD tray decreased lower(p<0.05) than those of others. Carbon dioxide contents in trays were increased from 0.5% to 5.5%~8.6% within 1 day storage. Oxygen contents in trays were sharply decreased from 20% to 0.8%~8.2% within 1 day storage. Lightness of oyster mushroom increased all trays. Off flavor appeared stronly in oyster mushroom packed in EPS, AKD and PEG during storage, but was not detected in mushroom packed in starch and CMC until 4 days storage.

• 마이크로전자및패키징학회지
• /
• 제22권1호
• /
• pp.69-74
• /
• 2015

첨단 전자기기에 사용되는 전자부품의 크기와 접속피치가 감소하면서 리플로우 공정 후 플럭스 잔사의 세정이 어려워짐에 따라 무세정 솔더 페이스트에 대한 요구가 증가하고 있다. 본 연구에서는 SAC305 솔더분말과 에폭시 레진을 주성분으로 하는 경화성 플럭스를 혼합하여 제조한 에폭시 경화형 솔더 페이스트에 대하여 리플로우 공정성, 플럭스 잔사의 부식성, 솔더볼 및 보드레벨 BGA 패키지 솔더 접합부의 기계적 거동을 기존 로진계 솔더 페이스트와 비교하여 평가하였다. 에폭시 경화형 솔더 페이스트는 솔더 접합부 주변에 경화물 필렛을 형성한 것으로 보아 플럭싱 작용에 의해 솔더 접합부가 형성된 이후에 경화반응이 진행되는 것을 확인할 수 있었으며, 동판에 대한 젖음성 시험을 통해 기존상용 솔더 페이스트 정도의 납퍼짐성을 갖는 것을 알 수 있었다. 리플로우 후 동판에 대한 고온 고습 시험을 통해 에폭시 경화형 솔더 페이스트는 동판 부식을 전혀 발생시키지 않는 것으로 나타났는데, 이는 FT-IR 분석결과 에폭시 경화반응을 통해 단단히 고정된 결과로 생각되었다. 볼전단, 볼당김 및 다이전단 시험 결과, 솔더 접합부 주변에 형성된 경화물 필렛은 솔더 표면과 접착본딩을 형성하며, 다이전단강도를 15~40% 정도 향상시키는 것으로 보아 에폭시 경화형 솔더 페이스트는 플럭스 잔사 세정공정의 생략과 함께 솔더 접합부 보강효과를 통해 패키지 신뢰성 향상에도 기여할 수 있을 것으로 생각되었다.