• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.5
• /
• pp.704-710
• /
• 2012

The lower portion of sloping paddy fields normally contains excessive moisture and the higher water table caused by the inflow of ground water from the upper part of the field resulting in non-uniform water content distribution. Four drainage methods namely Open Ditch, Vinyl Barrier, Pipe Drainage and Tube Bundle for multiple land use were installed within 1-m position from the lower edge of the upper embankment of sloping alluvial paddy fields. This study was conducted to evaluate soil physical characteristics by drainage improvement in poorly drained sloping paddy field. The results showed that subsurface drainage by Pipe Drainage improves the productivity of poorly drained soils by lowering the water table and improving root zone soil layer condition. In an Pipe drainage plot, soil moisture drained faster as compared to the other drainage methods. Infiltration rate showed high tendency to Piper Drainage method about $20.87mm\;hr^{-1}$ than in Open Ditch method $0.15mm\;hr^{-1}$. And Similarly soil water and degree of hardness and shear strength phase of soil profile showed a tendency to decrease. From the above results, we found that when an subsurface drainage was established with at 1m position from the lower edge paddy levee of the upper field in sloping poorly drained paddy fields Pipe Drainage was the most effective drainage system for multiple land use.

• Journal of Korean Medical classics
• /
• v.11 no.1
• /
• pp.416-512
• /
• 1998

The following conclusions are obtained from the studies on the chapters concerning phisiology, pathology, daily conduct, materia medica, pulse, and urinalysis from , of the "Four Tantras". 1. The theoretical basis forming the Tibetan Medicine is the substance of phlegm, bile, and wind each of which is divided into five kinds. These phisiological substances can be transformed into pathological factors when certain environment is formed. 2. In embryology, the semen of the father and menstral blood of mother is considered the most important condition in conception, and the Five factors are regarded as important. There is a detailed explanation of development of the fetus while it stays in the womb of mother during 38weeks, such as the formation of the viscera, channels, sense organs, etc. 3. There is metaphor which compares the human body with the king's palace. With the development of human anatomy, there is the detailed anatomical picture of anterior and posterior aspects of human body. And also there is the measurement of physiological constitution and the three fluids. 4. In division of the channels, they concerned the now of the blood and distribution of the nerve fibers, and each channel is connected with one another. The division of the cannel is namely embryonic channel, channel of existence, channel of connection, and the course of life principle. 5. The seven bodily constituents and three factors of phlegm, bile, and wind are important in sustaining the life of human body as well as growth and maturization, and when their equilibrium is broken, the human body is degnerated, and finally death comes. 6. The signs of death is divided into distant sign, remote sign, certain sign. and uncertain sign, and is used as a clue in diagnosis of the disease. Especially there is a mention about the mechanism of the dreams, and different dreams according to the condition of the patient. 7. In pathology, there is the cause of the disease, the environmental factors which can induce disease, the path by which disease come into the human body, the characteristics of the disease, and the kinds of disease. 8. There is a mention about the conduct, and it is divided into the daily conduct, the mental attitude, and the side-effects which can occur when one puts up with the physiological actions of the body. 9. The daily diet is divided into food and beverage. The food is divided again into grain, meat, fat, boiled food, and spiced food, and the beverage into milk, water, and wine. 10. The pulsation should be taken in lift hand to diagnose heart, small intestine, stomach, spleen, kidney, reproductive organ, and in right hand jungs, large intestine, liver, gall bladder, kidney, and bladder. In the healthy person, the pulse moves 5times in one perspiration, and the type of pulse is constant while the pulse moves 100times. But unhealthy person's pulse is different from this. The urinalysis is the unique part of Tibetan Medicine, and is important in examination of the disease. One should decide which of the three factors are dominant by the obervation of the color, amount of the steam and how long it lasts, odour, foam, and the shape of the swirl in three different states when the urine is hot, warm, and cold. One can determine the life of the patient and which viscera is the cause of the disease by the pulse, and whether the nature of the disease is hot or cold by the urinalysis. 11. The materia medica contains gemstones, minerals, plateau medication, and meat products.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.17 no.4
• /
• pp.52-68
• /
• 2014

In this study, we investigated the seasonal variation of SST(Sea Surface Temperature) and thermal effluents estimated by using Landsat-7 ETM+ around the Kori Nuclear Power Plant for 10 years(2000~2010). Also, we analyzed the direction and range of thermal effluents dispersion by the tidal current and tide. The results are as follows, First, we figured out the algorithm to estimate SST through the linear regression analysis of Landsat DN(Digital Number) and NOAA SST. And then, the SST was verified by compared with the in situ measurement and NOAA SST. The determination coefficient is 0.97 and root mean square error is $1.05{\sim}1.24^{\circ}C$. Second, the SST distribution of Landsat-7 estimated by linear regression equation showed $12{\sim}13^{\circ}C$ in winter, $13{\sim}19^{\circ}C$ in spring, and $24{\sim}29^{\circ}C$ and $16{\sim}24^{\circ}C$ in summer and fall. The difference of between SST and thermal effluents temperature is $6{\sim}8^{\circ}C$ except for the summer season. The difference of SST is up to $2^{\circ}C$ in August. There is hardly any dispersion of thermal effluents in August. When it comes to the spread range of thermal effluents, the rise range of more than $1^{\circ}C$ in the sea surface temperature showed up to 7.56km from east to west and 8.43km from north to south. The maximum spread area was $11.65km^2$. It is expected that the findings of this study will be used as the foundational data for marine environment monitoring on the area around the nuclear power plant.

• Journal of the Korean earth science society
• /
• v.36 no.1
• /
• pp.90-108
• /
• 2015

The WRF-Chem model was applied to simulate the Asian dust event affecting the Korean Peninsula from 11 to 13 November 2010. GOCART dust emission schemes, RADM2 chemical mechanism, and MADE/SORGAM aerosol scheme were adopted within the WRF-Chem model to predict dust aerosol concentrations. The results in the model simulations were identified by comparing with the weather maps, satellite images, monitoring data of $PM_{10}$ concentration, and LIDAR images. The model results showed a good agreement with the long-range transport from the dust source area such as Northeastern China and Mongolia to the Korean Peninsula. Comparison of the time series of $PM_{10}$ concentration measured at Backnungdo showed that the correlation coefficient was 0.736, and the root mean square error was $192.73{\mu}g/m^3$. The spatial distribution of $PM_{10}$ concentration using the WRF-Chem model was similar to that of the $PM_{2.5}$ which were about a half of $PM_{10}$. Also, they were much alike in those of the UM-ADAM model simulated by the Korean Meteorological Administration. Meanwhile, the spatial distributions of $PM_{10}$ concentrations during the Asian dust events had relevance to those of both the wind speed of u component ($ms^{-1}$) and the PBL height (m). We performed a regressive analysis between $PM_{10}$ concentrations and two meteorological variables (u component and PBL) in the strong dust event in autumn (CASE 1, on 11 to 23 March 2010) and the weak dust event in spring (CASE 2, on 19 to 20 March 2011), respectively.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.2
• /
• pp.213-230
• /
• 2008

The aim of this study was to analyze the initial movement and the stress distribution of each tooth and periodontal ligament during the lingual lever-arm retraction of 6 maxillary incisors using FEA. Two kinds of finite element models were produced: 2-properties model (simple model) and 24-properties model (multi model) according to the material property assignment. The subject was an adult male of 23 years old. The DICOM images through the CT of the patient were converted into the 3D image model of a skull using the Mimics (version 10.11, Materialise's interactive Medical Image Control System, Materialise, Belgium). After series of calculating, remeshing, exporting, importing process and volume mesh process was performed, FEA models were produced. FEA models are consisted of maxilla, maxillary central incisor, lateral incisor, canine, periodontal ligaments and lingual traction arm. The boundary conditions fixed the movements of posterior, sagittal and upper part of the model to the directions of X, Y, Z axis respectively. The model was set to be symmetrical to X axis. Through the center of resistance of maxilla complex, a retraction force of 200g was applied horizontally to the occlusal plane. Under this conditions, the initial movements and stress distributions were evaluated by 3D FEA. In the result, the amount of posterior movement was larger in the multi model than in the simple model as well as the amount of vertically rotation. The pattern of the posterior movement in the central incisors and lateral incisors was controlled tipping movement, and the amount was larger than in the canine. But the amount of root movement of the canine was larger than others. The incisor rotated downwardly and the canines upwardly around contact points of lateral incisor and canine in the both models. The values of stress are similar in the both simple and multi model.

• Korean Journal of Plant Resources
• /
• v.27 no.5
• /
• pp.546-555
• /
• 2014

The final aim of this study is to develop a biofiltration system integrated with plant vegetation for improving indoor air quality effectively depending on indoor space and characteristics. However, to approach this final goal, several requirements such as constant pressure drops (PDs) and soil moisture contents (SMCs), which influence the capacity design for a proper ventilation rate of biofiltration system, should be satisfied. Thus, this fundamental experiment was carried out to adjust a proper wind speed and to ensure a stabilization of initial SMCs within biofilter for uniform distribution of SMCs and PDs, and for normal plant growth, especially avoiding root stress by wind. Therefore, we designed horizontal biofliter models and manufactured them, and then calculated the ventilation rate, air residence time, and air-liquid ration based on the biofilter depending on three levels of wind speed (1, 2, and $3cm{\cdot}s^{-1}$). The relative humidity (RH) and PD of the humidified air coming out through the soil within the biofilter, and SMC of the soil and plant growth parameters of lettuce and duffy fern grown within biofilter were measured depending on the three levels of wind speed. As a result of wind speed test, $3{\cdot}sec^{-1}$ was suitable to keep up a proper RH, SMC, and plant growth. Thus, the next experiment was set up to be two levels of initial SMCs (low and high initial SMC, 18.5 and 28.7%) within each biofilter operated and a non-biofiltered control (initial SMC, 29.7%) on the same wind speed ($3cm{\cdot}sec^{-1}$), and measured on the RH and PD of the air coming out through the soil within the biofilter, and SMC of the soil and plant growth parameters of Humata tyermani grown within biofilter. This result was similar to the first results on RHs, SMCs, and PDs keeping up with constant levels, and three SMCs did not show any significant difference on plant growth parameters. However, two biofiltered SMCs enhanced dry weights of the plants slightly than non-biofiltered SMC. Thus, the stability of this biofiler system keeping up major physical factors (SMC and PD) deserved to be adopted for designing an advanced integrated biofilter model in the near future.

• Journal of the Korean earth science society
• /
• v.32 no.3
• /
• pp.276-293
• /
• 2011

In this study a modeling system consisting of Weather Research and Forecasting (WRF), Sparse Matrix Operator Kernel Emissions (SMOKE), the Community Multiscale Air Quality (CMAQ) model, and the CMAQ-Model of Aerosol Dynamics, Reaction, Ionization, and Dissolution (MADRID) model has been applied to estimate enhancements of $PM_{10}$ during Asian dust events in Korea. In particular, 5 experimental formulas were applied to the WRF-SMOKE-CMAQ (MADRID) model to estimate Asian dust emissions from source locations for major Asian dust events in China and Mongolia: the US Environmental Protection Agency (EPA) model, the Goddard Global Ozone Chemistry Aerosol Radiation and Transport (GOCART) model, and the Dust Entrainment and Deposition (DEAD) model, as well as formulas by Park and In (2003), and Wang et al. (2000). According to the weather map, backward trajectory and satellite image analyses, Asian dust is generated by a strong downwind associated with the upper trough from a stagnation wave due to development of the upper jet stream, and transport of Asian dust to Korea shows up behind a surface front related to the cut-off low (known as comma type cloud) in satellite images. In the WRF-SMOKE-CMAQ modeling to estimate the PM10 concentration, Wang et al.'s experimental formula was depicted well in the temporal and spatial distribution of Asian dusts, and the GOCART model was low in mean bias errors and root mean square errors. Also, in the vertical profile analysis of Asian dusts using Wang et al's experimental formula, strong Asian dust with a concentration of more than $800\;{\mu}g/m^3$ for the period of March 31 to April 1, 2007 was transported under the boundary layer (about 1 km high), and weak Asian dust with a concentration of less than $400\;{\mu}g/m^3$ for the period of 16-17 March 2009 was transported above the boundary layer (about 1-3 km high). Furthermore, the difference between the CMAQ model and the CMAQ-MADRID model for the period of March 31 to April 1, 2007, in terms of PM10 concentration, was seen to be large in the East Asia area: the CMAQ-MADRID model showed the concentration to be about $25\;{\mu}g/m^3$ higher than the CMAQ model. In addition, the $PM_{10}$ concentration removed by the cloud liquid phase mechanism within the CMAQ-MADRID model was shown in the maximum $15\;{\mu}g/m^3$ in the Eastern Asia area.

• Journal of Korean Society of Forest Science
• /
• v.58 no.1
• /
• pp.34-40
• /
• 1982

Main consideration of this trial is to know whether the planting work should be possible to do not only in the early spring but also in the summer or autumn, for giving the guide to get the work plan and to broaden the employing season of the skilled forest worker. Seedling of Pinus koraiensis, Larix leptolepsis, Pinus rigida, Pinus rigida${\times}$ P. taeda(wind) and Chamaecyparia obtusa as the test species had been planted in 15 days interval from the middle of March to the end of November. The seedling survival was investigated in the spring time of coming year because the winter damage could be problems. At the same time the climate data was measured daily and the shoot growth of test species were also measured in other near plantation at 15 days interval to know the influence to survival. From these results the spring and autumn planting is showing the good survival and the summer planting seems to give the difficulties. The spring planting in the southern temperate zone could be stared earlier as the end of February or beginning of March because the soil temperature are increasing up more $5^{\circ}C$ from this time. But the summer planting from the beginning of May until the end of August in better to avoid with excluding specially the good season of rainfall distribution because of the shoot growth of green confer seedling and the leave sprouting of Larix leptolepsis are so vigorously growing up from the begining of May and its wood structure is too weak to compensate the water loss. But among the test species Pinus koraiensis and Chamaecyparis obtusa have more possibility to plant in the summer season. The autumn planting seems to be very reasonable to accept newly in the trial region. This may be the reasons of still high soil temperature to grow the seedling root and of hardened school to resist from the dry winter wind. But it will be carefully that the strongly exposured site could be to avoid for the autumn planting in case of specially Pinus rigida${\times}$P. taeda and Chamaecyparis obtusa. From these discussion the guide table 1 for planting season with the test species is proposed and can be used for planing and employing in the trial zone.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.13 no.4
• /
• pp.176-184
• /
• 2011

Cold air on sloping surfaces flows down to the valley bottom in mountainous terrain at calm and clear nights. Based on the assumption that the cold air flow may be the same as the water flow, current models estimate temperature drop by regarding the cold air accumulation at a given location as the water-like free drainage. At a closed catchment whose outlet is blocked by man-made obstacles such as banks and roads, however, the water-like free drainage assumption is no longer valid because the cold air accumulates from the bottom first. We developed an empirical model to estimate quantitatively the effect of cold pool on nocturnal temperature in a closed catchment. In our model, a closed catchment is treated like a "vessel", and a digital elevation model (DEM) was used to calculate the maximum capacity of the cold pool formed in a closed catchment. We introduce a topographical variable named "shape factor", which is the ratio of the cold air accumulation potential across the whole catchment area to the maximum capacity of the cold pool to describe the relative size of temperature drop at a wider range of catchment shapes. The shape factor is then used to simulate the density profile of cold pool formed in a given catchment based on a hypsometric equation. The cold lake module was incorporated with the existing model (i.e., Chung et al., 2006), generating a new model and predicting distribution of minimum temperature over closed catchments. We applied this model to Akyang valley (i.e., a typical closed catchment of 53 $km^2$ area) in the southern skirt of Mt. Jiri National Park where 12 automated weather stations (AWS) are operational. The performance of the model was evaluated based on the feasibility of delineating the temperature pattern accurately at cold pool forming at night. Overall, the model's ability of simulating the spatial pattern of lower temperature were improved especially at the valley bottom, showing a similar pattern of the estimated temperature with that of thermal images obtained across the valley at dawn (0520 to 0600 local standard time) of 17 May 2011. Error in temperature estimation, calculated with the root mean square error using the 10 low-lying AWSs, was substantially decreased from $1.30^{\circ}C$ with the existing model to $0.71^{\circ}C$ with the new model. These results suggest the feasibility of the new method in predicting the site-specific freeze and frost warning at a closed catchment.

• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.3
• /
• pp.223-227
• /
• 2008

This experiment was conducted to describe the distribution of stable isotope Cd in the mine tailing and uncultivated soils derived from different parent rocks (Igneous rock, Metamorphic rock, and Sedimentary rock) as well as the movement of Cd isotopes from soil to plants, soybean and pepper. The results showed that there was no significant difference in isotopic ratios in soil among the eight kinds of stable isotope of Cd. However the relationship among isotopic ratios of stable isotope of Cd in soils were classified to four types, linear type between $Cd^{106}/Cd^{111}$ and $Cd^{108}/Cd^{111}$, quadratic type between $Cd^{114}/Cd^{108}$ and $Cd^{111}/Cd^{110}$, reverse quadratic type between $Cd^{110}/Cd^{116}$ and $Cd^{108}/Cd^{116}$, and cluster type between $Cd^{110}/Cd^{113}$ and $Cd^{116}/Cd^{113}$. While the individual stable isotopes of Cd in root were remained except on the plot of pepper without mine tailing application. $Cd^{116}$, $Cd^{114}$, and $Cd^{112}$ played active roles among other stable isotopic Cds in bean and red pepper, and $Cd^{116}$ was ranked the highest abundance ratio. Contrary to crop itself, the abundance ratios of $Cd^{116}$ in bean and read pepper roots were decreased, and the ones of other Cds were relatively increased.