• Journal of Korean Institute of Industrial Engineers
• /
• v.24 no.4
• /
• pp.649-660
• /
• 1998

Steel making in Mini Mill consists of three major processing stages: molten steel making in an electric arc fuenace, slab casting in a continuous caster, and hot rolling in a finishing mill. Each processing stage has its own lot grouping criterion. However, these criteria in three stages are conflicting with each other. Therefore, delveloping on efficient lot grouping algorithm to enhance the overall productivity of the Mini Mill is an extremely difficult task. The algorithm proposed in this paper is divided into three steps hierarchically: change grouping, cast grouping, and roll grouping. An efficient charge grouping heuristic is developed by exploiting the characteristics of the orders, the processing constraints and the requirements for the downstream stages. In order to maximaize the productivity of the continuous casters, each cast must contain as many charges as possible. Based on the constraint satisfaction problem technique, an efficient cast grouping heuristic is developed. Each roll consists of two casts satisfying the constraints for rolling. The roll grouping problem is formulated as a weighted non-bipartite matching problem, and an optimal roll grouping algorithm is developed. The proposed algorithm is programmed with C language and tested on a SUN Workstation with real data obtained from the H steel works. Through the computational experiment, the algorithm is verified to yield quite satisfactory solutions within a few minutes.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.1
• /
• pp.59-69
• /
• 2001

Ths paper presents an algorithm of detecting eccentricity signal and diagnosing the cause in rolling process. A designed technique uses only the outputs of load cell and tachorreter, which are generally utilized in rolling process, and need not any acklitional sensors. Detecting signals related to eccentricity is done by combining outputs of 6 digital bandPass filters whose center frequency are varied with roll's rotating frequency. A function of diagnosing the cause of occentricity from extracted data having occentricity components is implemented by defining reasonable variables. In order to show validity of an algorithm designed in this paper, simulation was accomplished for three groups. The first is that some portion of roll in the direction of roll circumference is distorted. The second is that rotating axis and roll center is not identical. The third is that composite cause is occmed Simulation results show that every kind of eccentricity can be diagnosed in terms of algorithm proposed.oposed.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.7
• /
• pp.3185-3190
• /
• 2016

Background: This study was designed to compare radioguided versus routine wire localization of nonpalpable non-malignant breast lesions in terms of efficacy for complete excision, ease of use, time saving, and cosmetic outcome. Materials and Methods: Patients with non-palpable breast masses and non-malignant core biopsy results who were candidates for complete surgical lumpectomy were enrolled and randomly assigned to radioguided or wire localization groups. Radiologic, surgical, and pathologic data were collected and analyzed to determine the difficulty and duration of each procedure, ease of use, accuracy, and cosmetic outcomes. Results: This prospective randomized study included 60 patients, randomly divided into wire guided localization (WGL) or radioguided occult lesion localization (ROLL) groups. The mean duration of localization under ultrasound guidance was shorter in the ROLL group (14.4 min) than in the WGL group (16.5 min) (p<0.001). The ROLL method was significantly easier for radiologists (p=0.0001). The mean duration of the surgical procedure was 22.6 min (${\pm}10.3min$) for ROLL and 23.6 min (${\pm}9.6min$) for WGL (p=0.6), a non-significant difference. Radiography of the surgical specimens showed 100% lesion excision with clear margins, as proved by pathologic examination, with both techniques. The surgical specimens were slightly heavier in the ROLL group, but the difference was not significant (p=0.06). Conclusions: The ROLL technique provides effective, fast, and simple localization and excision of non-palpable non-malignant breast lesions.

• Korean Journal of Metals and Materials
• /
• v.50 no.7
• /
• pp.503-509
• /
• 2012

We report on the feasibility of producing 6xxx series Al alloy sheets using a combination of twin-roll strip casting and asymmetric rolling. The Al alloy sheets produced in this study exhibited an excellent formability ($\bar{r}=1.2$, ${\Delta}r=0.17$) and mechanical properties (${\sigma}_{TS}{\sim}260MPa$, ${\varepsilon}>30%$), which cannot be feasibly obtained via the conventional technique based on ingot casting and conventional rolling. The enhanced formability as evaluated in terms of $\bar{r}$ and ${\Delta}r$ was clarified by examining the evolution of textures associated with strip casting and subsequent thermo-mechanical treatments. The evaluation of the formability leads us to conclude that the combined technique based on strip casting and asymmetric rolling is a feasible process for enhancing the formability of Al alloy sheets to a level beyond which the conventional technique can reach.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.413-416
• /
• 2007

In general, by means of the electrodepositing technique, a copper foil sample was prepared with a high purity and a high density. But the mechanical properties of the electrodepositing copper foil was lower than it's the rolling copper foil. However, the production of copper foil with approximately 36 microns thick in rolling process was very difficult. This paper describes the outline of the high accuracy cold rolling in 6 high mill which was developed for the purpose of rolling very thin accurate gauge copper foil(36 micron thick), and give several rolling characteristic of 600 mm wide copper foil. a) Large strain can be accumulated pass by pass in industrial multi-pass rolling processing to overcome large critical strain for thickness accuracy through optimization of rolling schedule. b) Also, permissible tension for rolling 0.45 $\sim$ 0.036 mm thick copper strip stably in accordance with the each pass work had been established by FEM simulation results. c) During the plate rolling process, considerable values of the forces of material pressure on the tool occur. These pressures cause the elastic deformation of the roll, thus changing the shape of the deformation region. A numerical simulation of roll deflection during cold rolling is presented in the paper. d) The proposed pass schedule can roll very thin copper foil of 36 micron thickness to a tolerance of ${\pm}1$ microns. The validity of simulated results was verified into rolling experiments on the copper foil.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.913-922
• /
• 1987

In this paper the solidification phenomena at the molten pool has been modeled and simulated in terms with the one dimensional unsteady-state heat transfer of the solid and molten phase and the pressure distribution in the solid phase for the twin-roller continuous casting of Sn-15% Pb. The further purpose of this study was to effectively analyze the thermal and mechanical deformation of roll applying the results of the heat transfer and the pressure distribution to the boundary conditions. The strip thickness of rapidly solidified metallic strip decreases with increasing angular velocity of the roller and with increasing initial roll gap. For this reason the roll spacing and angular velocity of the rolls are considered to be main variables. The recommended optimal casting regimes for continuous strip dimensions is near 0.8mm-1.0mm in thickness at the given angular velocity .omega.=2.0 rad/sec. Results of the experiment using Sn-15% Pb are compared with model predictions. The calculated roll deformation has been in good agreement with the observed value of roll deformatiion. All the deformation. All the deformation of the roller is within the elastic range, the plastic yielding are not occured. However, these elastic stresses are sufficient to take place of the shortened roller life by the thermal fatigue and a notch fatigue. The higher cooling rates were obtained by a twin-roller quenching technique. Also the quenched microstructure of the rapidly solidified shell was verified.

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.263-267
• /
• 2011

The present study was carried out to evaluate the microstructural and mechanical properties of cross-roll rolled pure copper sheets, and the results were compared with those obtained for conventionally rolled sheets. For this work, pure copper (99.99 mass%) sheets with thickness of 5 mm were prepared as the starting material. The sheets were cold rolled to 90% thickness reduction and subsequently annealed at $400^{\circ}C$ for 30 min. Also, to analyze the grain boundary character distributions (GBCDs) on the materials, the electron back-scattered diffraction (EBSD) technique was introduced. The resulting cold-rolled and annealed sheets had considerably finer grains than the initial sheets with an average size of 100 ${\mu}M$. In particular, the average grain size became smaller by cross-roll rolling (6.5 ${\mu}M$) than by conventional rolling (9.8 ${\mu}M$). These grain refinements directly led to enhanced mechanical properties such as Vickers micro-hardness and tensile strength, and thus the values showed greater increases upon cross-roll rolling process than after conventional rolling. Furthermore, the texture development of <112>//ND in the cross-roll rolling processed material provided greater enhancement of mechanical properties relative to the case of the conventional rolling processed material. In the present study, we systematically discuss the enhancement of mechanical properties in terms of grain refinement and texture distribution developed by the different rolling processes.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.2
• /
• pp.1-6
• /
• 2019

With the increase in number of the athletic population and elderly demographic, the demand for orthopedic splints, which are used to support a damaged body, has rapidly increased. Current splints mainly consist of inner and outer parts, which are multiple fabrics covered with polyurethane and nonwoven fabrics, respectively. However, the laminated materials with directly applied pre-polymer coating lead to a high defect rate because of the uneven thickness on the surface. Thus, this study proposes an indirect coating method using a precise clearance controller, which enables the even application of the coating material on multiple inner parts while maintaining a constant thickness. In addition, a roll-to-roll (R2R) technique is applied instead of the sewing mechanism to bond the inner and outer materials together and enhance the productivity in the final stage. In the advanced methods, there is a storage tank that contains polyurethane, a clearance controller, and pairs of rollers in the upper and lower rows. To improve the quality of the products and optimize the equipment, three controllable factors are determined: the viscosity of polyurethane, angle of the gap controller and number of pairs of rollers in the R2R system.

• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.12-17
• /
• 2007

• Journal of Computational Design and Engineering
• /
• v.3 no.4
• /
• pp.337-348
• /
• 2016

An experimental approach is presented for the measurement of wear that is common in the threading of cold-forged steel. In this work, the first objective is to measure wear on various types of roll taps manufactured to tapping holes in microalloyed HR45 steel. Different geometries and levels of wear are tested and measured. Taking their geometry as the critical factor, the types of forming tap with the least wear and the best performance are identified. Abrasive wear was observed on the forming lobes. A higher number of lobes in the chamber zone and around the nominal diameter meant a more uniform load distribution and a more gradual forming process. A second objective is to identify the most accurate data-mining technique for the prediction of form-tap wear. Different data-mining techniques are tested to select the most accurate one: from standard versions such as Multilayer Perceptrons, Support Vector Machines and Regression Trees to the most recent ones such as Rotation Forest ensembles and Iterated Bagging ensembles. The best results were obtained with ensembles of Rotation Forest with unpruned Regression Trees as base regressors that reduced the RMS error of the best-tested baseline technique for the lower length output by 33%, and Additive Regression with unpruned M5P as base regressors that reduced the RMS errors of the linear fit for the upper and total lengths by 25% and 39%, respectively. However, the lower length was statistically more difficult to model in Additive Regression than in Rotation Forest. Rotation Forest with unpruned Regression Trees as base regressors therefore appeared to be the most suitable regressor for the modeling of this industrial problem.