• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.7
• /
• pp.689-694
• /
• 2008

This paper proposes a roll rate estimation method for spinning vehicles. The carrier phase and frequency variations caused by spinning of vehicles are observed and the roll rate estimator is designed on the observation. The roll rate estimator consists of phase detector and zero crossing counter. The phase detector computes phase variation using in-phase and quadrature value from the correlator. By using zero crossing counter, the roll rate can be estimated since the output of phase detector is changed in proportion to the roll rate. Experiment a results show that estimated roll rate error is smaller than 0.0578Hz.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.753-760
• /
• 2007

In this paper, a roll and pitch estimation algorithm using a set of accelerometers and wireless sensor networks(S/N) is presented for use in a passenger vehicle. While an inertial measurement unit(IMU) is generally used for roll/pitch estimation, performance may be degraded in the presence of longitudinal acceleration and yaw motion. To compensate for this performance degradation, a new roll and pitch estimation algorithm is proposed that uses an accelerometer array, global positioning system(GPS) and in-vehicle networks to get information from yaw rate and roll rate sensors. Angular acceleration and roll and pitch approximation are first calculated based on vehicle kinematics. A discrete Kalman filter is then applied to estimate both roll and pitch more precisely by reducing noise from the running engine and from road disturbance. Finally, the feasibility of the proposed algorithm is shown by comparing its performance experimentally with that of an IMU in the framework of an indoor test platform as well as a test vehicle.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.303-306
• /
• 2006

A roll rate estimation method is proposed using the GPS measurement for spinning vehicles such as guided munitions and smart bombs. Before designing the roll rate estimator, the carrier phase and the carrier frequency deviation caused by spinning have been observed. Based on the observation, the spinning frequency is estimated using I and Q value from the correlator. The proposed method is evaluated through computer simulations using a software defined receiver and a GPS IF signal generator.

• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.3
• /
• pp.109-118
• /
• 2016

The present paper proposes a method that can estimate a roll rate of spinning vehicles utilizing GPS receivers. The proposed method analyzes a relation between received signal and correlation value and utilizes a phenomenon that received signal power that changes according to a signal incident direction affects a correlation value. That is, a roll-rate estimation method using zero crossing detection method for correlation value, which has sinusoidal periodicity according to rotations of vehicles, is proposed. A correlation value in real environments experiences a jitter so that the proposed method includes a pre-processing filter and detection threshold setting way is also considered to reduce the effect of received signal power. In order to verify the operation of the proposed method and analyze the performance, a signal generator and software-defined receiver (SDR) are designed. The signal generator generates intermediate frequency (IF) signal by taking the rotation of vehicles, antenna gain, and signal power into consideration, and a correlation value is acquired by taking the generated IF signals into consideration. Using the generated correlation value, the operation of the proposed roll rate estimation method is verified and the performance is analyzed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.6
• /
• pp.633-641
• /
• 2015

The ROM (roll over mitigation) system is a next-generation suspension system that can improve vehicle-driving stability and ride comfort. Currently, mass-produced safety systems, such as ESC (electronic stability control) and ECS (electronic control suspension), enable measurements of longitudinal and lateral acceleration as well as yaw rate through inertial sensor clusters, but they lack direct measurements of the roll angle. Therefore, in this paper, a roll angle estimation algorithm from ESC system sensors and tire normal force has been proposed. Furthermore, this study presents a method for roll over mitigation force distribution between the front and rear of a ROM system. Performance and reliability of the roll angle estimation and roll over mitigation force distribution were investigated through simulations. The simulation results showed that the proposed control algorithm and strategy are reliable during vehicle rollovers.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.133-140
• /
• 2015

In this paper, a roll angle estimation method of a rolling airframe using a low grade GPS and a roll rate gyro is proposed. The strength of the received signal of the GPS antenna attached on the rolling airframe is maximized when the GPS satellite is placed on the plane determined by the x-axis of the rolling airframe and the GPS antenna axis. Under the assumption that the x-axis of the rolling airframe is coincident with its velocity vector, the roll angle of the rolling airframe is calculated from the relative position vector of the satellite to the GPS when the GPS signal strength becomes maximum. The Kalman filter combined with a roll rate gyro is introduced to increase the determination accuracy of the roll angle. The performance of the proposed method is verified via 6-DOF simulations.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.5
• /
• pp.257-263
• /
• 2022

Active stabilizers use signals such as steering angle, yaw rate, and lateral acceleration to vary the roll stiffness of the front and rear suspension depending on the vehicle's driving conditions, and are attracting attention as RSC (Roll Stability Control) system that suppresses roll when turning and improves ride comfort when going straight. Various studies have been conducted in relation to active stabilizer bars and RSC systems. However, accurate modeling of passive stabilizer model and active stabilizer model and vehicle dynamics analysis result verification are insufficient, and performance result analysis related to vehicle roll angle estimation and electric motor control is insufficient. Therefore, in this study, an accurate vehicle dynamics model was constructed by measuring the passive/active stabilizer bar model and component parameters. Based on this, the analysis result with high reliability was derived by comparing the roll angle estimation algorithm based on the lateral acceleration and suspension of the vehicle with the actual vehicle driving test result. In addition, it was intended to accurately analyze the motor torque characteristics and roll reduction effects of the electric motor-driven RSC system.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.1932-1934
• /
• 2001

In this paper, a horizontal LOS(line of sight) rate estimator for conventional sea skimming ASM(anti-ship missile) is proposed. A LOS rate dynamics model in 2 axis gimbal system and in homing geometry is derived. And a new LOS rate estimator is proposed by applying a Kalman filter theory to the LOS rate dynamics model. The proposed filter can estimate LOS rates with taking roll motions into account. Simulation results show the proposed filter produces smaller estimation errors than a conventional method.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.194.1-194.1
• /
• 2005

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1103-1108
• /
• 2007

This paper describes a robust model-based roll state estimator for application to the detection of impending vehicle rollover. The roll state estimator is based on a 2-D bicycle model and a roll model to estimate the maneuver-induced vehicle roll motion. The measurement signals are lateral acceleration, yaw rate, steering angle, and vehicle speed. Vehicle mass is adapted to obtain robust performance of the estimator. Computer simulation is conducted to evaluate the proposed roll state estimator by using a validated vehicle simulator. It is shown that the roll state estimator shows robust performance without exact vehicle mass information.