• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.753-760
• /
• 2007

In this paper, a roll and pitch estimation algorithm using a set of accelerometers and wireless sensor networks(S/N) is presented for use in a passenger vehicle. While an inertial measurement unit(IMU) is generally used for roll/pitch estimation, performance may be degraded in the presence of longitudinal acceleration and yaw motion. To compensate for this performance degradation, a new roll and pitch estimation algorithm is proposed that uses an accelerometer array, global positioning system(GPS) and in-vehicle networks to get information from yaw rate and roll rate sensors. Angular acceleration and roll and pitch approximation are first calculated based on vehicle kinematics. A discrete Kalman filter is then applied to estimate both roll and pitch more precisely by reducing noise from the running engine and from road disturbance. Finally, the feasibility of the proposed algorithm is shown by comparing its performance experimentally with that of an IMU in the framework of an indoor test platform as well as a test vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.6
• /
• pp.633-641
• /
• 2015

The ROM (roll over mitigation) system is a next-generation suspension system that can improve vehicle-driving stability and ride comfort. Currently, mass-produced safety systems, such as ESC (electronic stability control) and ECS (electronic control suspension), enable measurements of longitudinal and lateral acceleration as well as yaw rate through inertial sensor clusters, but they lack direct measurements of the roll angle. Therefore, in this paper, a roll angle estimation algorithm from ESC system sensors and tire normal force has been proposed. Furthermore, this study presents a method for roll over mitigation force distribution between the front and rear of a ROM system. Performance and reliability of the roll angle estimation and roll over mitigation force distribution were investigated through simulations. The simulation results showed that the proposed control algorithm and strategy are reliable during vehicle rollovers.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.180.2-180
• /
• 2001

In the hot rolling process, the RF AGC (Roll Force Auto Gauge Control) is used to control the roll gap to reduce the variation of rolling force caused by the roll eccentricity and the variation of material thickness. However the effect of the roll eccentricity cannot be distinguished. To eliminate the effect of the roll eccentricity, the roll eccentricity estimation is needed to supplement some drawbacks of RF AGC. In this paper, an ALE(Adaptive Line Enhancer) that extracts the rolling force variation due to the roll eccentricity is suggested. We also provide an algorithm that enhances the convergence time of roll eccentricity estimation. The performance improvement of the Suggested algorithm is shown via simulations.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.7
• /
• pp.689-694
• /
• 2008

This paper proposes a roll rate estimation method for spinning vehicles. The carrier phase and frequency variations caused by spinning of vehicles are observed and the roll rate estimator is designed on the observation. The roll rate estimator consists of phase detector and zero crossing counter. The phase detector computes phase variation using in-phase and quadrature value from the correlator. By using zero crossing counter, the roll rate can be estimated since the output of phase detector is changed in proportion to the roll rate. Experiment a results show that estimated roll rate error is smaller than 0.0578Hz.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.69-80
• /
• 1993

It is important to prevent roll failure in hot rolling process for reducing maintenance coat and production loss. Roll material and rolling conditions such as the roll force and torque have been intensively investigated to overcome the roll failures. In this study, a computer roll life prediction system under working condition is developed and evaluated on IBM-PC level. The system is composed and fatigue estimation models which are stress analysis, crack propagation, wear and fatigue estimation. Roll damage can be predicted by calculating the stress anplification, crack depth propagation and fatigue level in the roll using this computer model. The developed system is applied to a work roll in actual hot rolling process for reliability evaluation. Roll failures can be diagnosed and the propriety of current working condition can be determined through roll life prediction simulation.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.5
• /
• pp.257-263
• /
• 2022

Active stabilizers use signals such as steering angle, yaw rate, and lateral acceleration to vary the roll stiffness of the front and rear suspension depending on the vehicle's driving conditions, and are attracting attention as RSC (Roll Stability Control) system that suppresses roll when turning and improves ride comfort when going straight. Various studies have been conducted in relation to active stabilizer bars and RSC systems. However, accurate modeling of passive stabilizer model and active stabilizer model and vehicle dynamics analysis result verification are insufficient, and performance result analysis related to vehicle roll angle estimation and electric motor control is insufficient. Therefore, in this study, an accurate vehicle dynamics model was constructed by measuring the passive/active stabilizer bar model and component parameters. Based on this, the analysis result with high reliability was derived by comparing the roll angle estimation algorithm based on the lateral acceleration and suspension of the vehicle with the actual vehicle driving test result. In addition, it was intended to accurately analyze the motor torque characteristics and roll reduction effects of the electric motor-driven RSC system.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.40-40
• /
• 2000

Generally a RF AGC controls the roll gap using the variation of rolling force caused by the roll eccentricity and the entry thickness of material, but these can not be classified. The Feed- forward AGC method, which controls the next stand roll 9ap by estimation the skid mark of the previous stand output thickness is needed to supplement the shortage of RF AGC. In this paper, an improved filtering method of skid mark which take account of the kinds of materials, the final objective thickness and the roll speed is proposed, In addition, an improved estimation method of control point using the speedometer and looper angle is suggested, Via simulation, the performance improvement of the suggested FF AGC method is verified.

• Ocean Systems Engineering
• /
• v.5 no.2
• /
• pp.55-76
• /
• 2015

Of all the six degrees of freedom, the roll motion of a ship is the most poorly understood and displays complicated phenomena. Due to the low potential wave damping at the natural frequency, the effective analysis of ship roll dynamics comes down to the accurate estimation of the viscous roll damping. This paper provides overview of the importance of roll damping and an extensive literature review of the various viscous roll damping prediction methods applied by researchers over the years. The paper also discusses in detail the current state of the art estimation of viscous roll damping for ship shaped structures. A computer code is developed based on this method and its results are compared with experimental data to demonstrate the accuracy of the method. While some of the key references describing this method are not available in English, some others have been found to contain typographic errors. The objective of this paper is to provide a comprehensive summary of the state of the art method in one place for future reference.

• Journal of computational fluids engineering
• /
• v.20 no.2
• /
• pp.81-87
• /
• 2015

For Underwater vehicles, Unwanted roll excursions are inevitable as they are caused by induced propeller torque, disturbances, and banking motion during turns. To estimate the manoeuvring performance of underwater vehicle, it is necessary to obtain the roll coefficient of body. This paper was covered estimation of roll coefficient of underwater vehicle using STAR-CCM+, commercial CFD(Computational Fluid Dynamics) code. The RANS equations for incompressible fluid flows was solved numerically by using a finite volume method. An MRF(Moving Reference Frame) Method was Also adopted for rotations of body. For the validation, the flow around a DARPA SUBOFF bare hull model was simulated and good agreement with experiments was obtained. And Pure roll coefficients were calculated and campared with the experimental data which were presented by Seoul National University. Finally, an underwater vehicle model with propeller was simulated and analyzed for estimation of roll coefficient variation caused by induced propeller torque.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.168-171
• /
• 2003

Generally RF AGC (Roll Force Automatic Gauge Control) controls the roll gap using the variation of rolling force caused by the roll eccentricity and the entry thickness of material, but RE AGC takes the bad effect of the roll eccentricity. The Feed-forward (FF) AGC method, which controls the next stand roll gap by the estimation of the thickness variation due to skid mark is needed to supplement the shortage of RF AGC. In this paper, an adaptive filtering method which takes account of the kind of material, the final objective thickness and the rolling speed is proposed to predict skid mark thickness variation. In addition, an improved estimation method of control point using a speedometer and looper angle is suggested. Via on line test, the performance improvement of the suggested FF AGC method is verified.