• 한국안전학회지
• /
• 제22권3호
• /
• pp.1-6
• /
• 2007

In order to evaluate fatigue endurance for the rocker arm of a diesel engine, stress measurements were performed using the strain gages attached near the neck, where is one of the most critical region in the rocker arm, in variation of the engine speed. The fatigue life experiments were carried out on miniature specimens from the rocker arms. For evaluating the fatigue endurance of the rocker arm, the S-N data were compared with the stress analysis results through FEM analysis of the rocker arm. The effective stress of the neck region was determined 17.7MPa through FEM analysis of the rocker arm. Conclusively, on the basis of fatigue limit, the rocker arm has a safety factor of 2.8 or 3.4 from the stress measurement or FEM results, respectively.

• 대한기계학회논문집A
• /
• 제29권9호
• /
• pp.1161-1168
• /
• 2005

As a result of vehicle maintenance of rocker arm shaft for 4-cylinder SOHC engine, failure analysis of rocker arm shaft is needed. Because more than $30\%$ of vehicles investigated have been fractured. Failure analysis is classified into an naked eyes, microscope and X-ray fractography etc. It can predict applied load as well as load type. These methods are applicable to components with simple boundary condition but aren't applicable to components with complex boundary condition. The existing fractography don't catch hold of failure boundary condition quantitatively. Especially, in case that the components isn't fractured at same position. We must determine the most dangerous failure boundary condition to evaluate their operation mechanism. The effect of various factors on response should be estimated to solve this statical problem. This study presents the most dangerous failure boundary condition of rocker arm shaft using orthogonal array and ANOVA in order to assure its robustness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.130.2-130.2
• /
• 2005

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.84-90
• /
• 2007

As a result of vehicle maintenance of rocker arm shaft for 4-cylinder SOHC engine, failure stress analysis of rocker arm shaft is needed. Because more than 30% of vehicles investigated have been fractured. Failure stress analysis is classified into an naked eyes, microscope, striation and X-ray fractography etc. Failure stress analysis by using striation is already established technology as means for seeking cause of fracture. But, although it is well known that striation spacing corresponds to the crack growth rate da/dN, it is not possible to determine ${\sigma}_{max}\;and\;{\sigma}_{min}$ under service loading only from striation spacing. This is because the value of striation spacing is influenced not only by ${\Delta}K$ but also by the stress ratio R. In the present paper, we determine the stress ratio using orthogonal array and ANOVA, and propose a prediction method of failure stress which is combined with FEM and striation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.198-202
• /
• 2004

This study proposes a new optimization algorithm which is combined with genetic algorithm and ANOM. This improved genetic algorithm is not only faster than the simple genetic algorithm, but also gives a more accurate solution. The optimizing ability and convergence rate of a new optimization algorithm is identified by using a test function which have several local optimum and an optimum design of rocker arm shaft. The calculation results are compared with the simple genetic algorithm.

• Tribology and Lubricants
• /
• 제19권4호
• /
• pp.195-202
• /
• 2003

Many computational researches have been performed about EHL film thickness in the contact between cam and follower in the engine valve train system. However, those computations do not explain the characteristics of dynamic film thickness which means squeeze film effect. Without the consideration of transient term in the Reynold's equation, the predicted film thickness from steady state condition has large difference from the actual film thickness. In this study, we have investigated the kinematic and dynamic simulations of rocker-arm valve train system. From the dynamic simulation, the applied load and the entraining velocity of the lubricant between cam and follower are obtained and with these values the dynamic film thickness is computed by Newton-Raphson method and compared with the steady state film thickness.

• 대한기계학회논문집A
• /
• 제29권6호
• /
• pp.835-841
• /
• 2005

This study proposes a new optimization algorithm which is combined with genetic algorithm and ANOM. This improved genetic algorithm is not only faster than the simple genetic algorithm, but also gives a more accurate solution. The optimizing ability and convergence rate of a new optimization algorithm is identified by using a evaluation function which have several local optimum and an optimum design of rocker arm shaft. The calculation results are compared with the simple genetic algorithm.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.318-322
• /
• 1999

An analytical study about dynamic behavior of center pivot rocker arm type valve train system equipped with roller of diesel engine is developed. At first, a mathematical model for the dynamic analysis has been set up using the lumped parameter method. In that model, valve spring is divided as some mass elemehts so as to simulate spring surging, Then, how the design parameters, such as valve mass, rocker arm inertia, valve spring stiffness, and initial load on valve spring, affect valve dynamic behavior especially in the valve close area is scrutinized.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.397-405
• /
• 2000

Many computational researches have been performed about EHL film thickness in the contact between cam and follower. However, those computations do not explain the characteristics of dynamic film thickness which means squeeze film effect. Without the consideration of transient term in the Reynold's equation, the predicted film thickness has large difference from the actual film thickness. In this study, we have investigated the kinematic and dynamic simulations of rocker-arm valve train system. From the simulation, the applied load and the entraining velocity of the lubricant between cam and follower are obtained and with these values the dynamic film thickness is computed by Newton-Raphson method and compared with the steady state film thickness.

• Journal of Biosystems Engineering
• /
• 제19권3호
• /
• pp.163-174
• /
• 1994

This study was conducted to investigate the dynamic motion of knife drive system of combine harvester. A computer program was developed to simulate the dynamic motion of the knife drive linkage and its algorithm was evaluated through experiments. The results are summarized as follows : 1. The theorectical horizontal (the direction of knife's reciprocating motion) reaction forces at the supporting point of rocker arm and crank arm were changed in the similar sinusoidal trends with the measured reaction forces. 2. The maximum values of shaking moment and reaction force per one revolution of crank arm followed polynomial trends as the rotational speed of crank shaft increased. The unbalanced force acting on the driving system increased at high speed. Therefore, the rotational speed of crank shaft should be maintained in proper range at increased forward speed to decrease vibration of the knife drive system. 3. The added mass to the crank arm increased the dynamic unbalanced force at the supporting point of rocker arm. It counterbalanced the reaction force at the supporting point of crank arm.