• Tunnel and Underground Space
• /
• v.26 no.5
• /
• pp.441-453
• /
• 2016

This study aimed to develop a two-component TSL suitable for reducing dust and guaranteeing homogeneous qualities during its spraying. Its performance was evaluated by a series of laboratory and field tests. High ductility of two-component TSL prototypes resulted in increasing their elongation at break even though their tensile strengths were slightly lower than those of one-component powder TSLs. One prototype of the two-component TSLs developed in this study was verified to satisfy every criterion specified by EFNARC (2008). Especially, it increased the average compressive strength of mortar specimens by 50% even when it coated them only with the thickness of 3 mm. From a preliminary spraying test, a spraying machine suitable for the developed TSL prototype was derived and modified. After its field application, dust and rebound generated during its spraying works were found to be very minimal. Its spraying rate was recorded to be approximately $60m^2/hr$. In addition, it showed a very rapid hardening characteristic compared with general sprayable waterproofing membranes.

• Tunnel and Underground Space
• /
• v.25 no.1
• /
• pp.46-55
• /
• 2015

A water tube with detonating cord was devised to control the blast dust. Water diffusion experiments with different detonating cord positions were conducted during the series of experiments to optimize the design parameters of the tube. Images from high speed camera were analyzed to evaluate the results. AUTODYN program was adopted to simulate the diffusion process of water and compared with the images. Diffusion of water shows cross flow in case of external charge while the internal case shows radial flow. A bubble ring was formed during the numerical analysis of internal charge case as occurred in underwater blast. An additional bubble ring was formed by the reflection pressure from the ground. And the Weber number was determined as sufficient for spray atomization performance of the water tube.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.9
• /
• pp.35-44
• /
• 2005

Recently, underground cavities such as limestone cavity and abandoned mine give rise to a lot of damage in SOC facilities. But there are many difficult problems such as delay of the working terms and enormous economic losses in finding a new method and changing construction design. In this study, a new filling material for underground cavities was developed using the stone-dust classified as industry waste polluting environment. As a result of test, filling material properties was that a compressive strength was $34{\~}60\;kgf/cm^2$, a change ratio in length was $0.268{\~}0.776\%$ and water absorption was $34.3{\~}46.9\%$. Also as a result of suspended mass test and pH test, it was confirmed that the developed filling material has a characteristic of non-separating in water and it was an environmentally friendly material.

• Explosives and Blasting
• /
• v.34 no.3
• /
• pp.10-16
• /
• 2016

Recently, transition from open pit to underground mining in limestone mines is an increasing trend in Korea due to environmental issues such as noise, dust and vibrations caused by crushers and equipment. The severe damages in the surrounding rock mass of underground opening caused by explosive blasting may lead to rock fall hazards or casualties. It is well known that variables which mainly affect blast-induced rock falls in underground mining are: blast vibration level, joint orientation and distribution and shape of the cross sections of underground structures. In this study, UDEC program, which is a DEM code, is used to simulate blast vibration-induced rock fall in underground openings. Variation of joint space, joint angle and joint normal stiffness was considered to investigate the effect of joint characteristics on the blast vibration-induced rock fall in underground opening. Finally, jointed rock mass models considering blast-induced damage zone were examined to simulate the critical blast vibration value which may cause rock falls in underground opening.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.10 no.1
• /
• pp.104-114
• /
• 2000

This study was carried out to estimate current status of dust concentrations in the factories producing non-metallic products in Korea. Data were gathered from the environmental monitoring reports by 40 workplace environmental monitoring institutes and the questionnaire designed for the study by the authors. A total of 1838 dust samples from 368 plants were obtained from the reports and were analyzed with no data modifications. But data on asbestos, rock wool, and welding fumes were excluded in this evaluation. The factories were classified into eight groups according to the standard industrial classification scheme in Korea. The results of this study were as follows; 1. The factories included were glass, non-refractory ceramic, refractory ceramic ware, structural non-refractory clay and ceramic, cement and lime, articles of concretes, and stone. Mean(geometric mean) concentrations of total dust samples ranged from $1.75(0.84)mg/m^3$ to $5.87(2.84)mg/m^3$. Statistically significantly higher dust concentrations were found in the cement and lime industries compared with other industries. 2. The non-compliance rates were 15.2% in glass and 20.6% in other non-metallic mineral products industries. Although all institutions surveyed utilized the identical sampling and classification scheme for dusts as specified in the current occupational exposure limits, wide discrepancies were found in collecting samples and classifying dusts. Further problems were discovered in classifying dusts. A dust sample collected could be classified into any of the three groups regardless of silica content. The results of this study showed that dust concentrations in the non-metallic products industries varied widely. Also discovered was classification errors of dust types among workplace monitoring institutes. These errors could adversely affect the results of exposure assessments and the true nature of dust hazards. Further, no institutions performed respirable dust sampling and analysis of crystalline silica. In order to correct these malpractices, current standards of occupational exposure limits should be revised and tight supervision by the Ministry of Labour be suggested.

• Journal of the Mineralogical Society of Korea
• /
• v.28 no.2
• /
• pp.165-171
• /
• 2015

Dust samples collected from air in metropolitan areas of Busan and Ulsan were analyzed by phase contrast microscopy, phase contrast dispersion microscopy and SEM. Asbestos concentration in dust samples was lower than detection limit. Many fibrous materials were observed in dust samples, but most of them were organic fibers. Inorganic fibers such as rock fiber, ceramic fiber and gypsum were contained in the samples and non-fibrous minerals such as quartz, calcite and feldspar were also occasionally observed. Domestic law requires that asbestos in air dust is mainly analyzed by phase contrast microscopy. From this study, however, precise analysis of asbestos was almost impossible by this method only. As indicated in JIS method of Japan, therefore, count and identification of asbestos were more efficient by dispersion staining method after removing organic materials in samples by low temperature incinerator.

• Journal of Environmental Science International
• /
• v.18 no.1
• /
• pp.41-47
• /
• 2009

In building demolition work, major dust-generating activities are blasting concrete and rock. The aim of this study was to find the characteristic of particle size of dusts which were generated during building demolition work using explosion. The DustMate of the Turnkey-Instruments Ltd. was used for particulate size-selective sampling of the four sites. TSP(Total Suspended Particle), PM10(Particle Matter $10{\mu}m$), PM2.5(Particle Matter $2.5{\mu}m$), and PM1.0(Particle Matter $1.0{\mu}m$) were measured during building demolition work using explosion. The large particulate (higher than the diameter $10{\mu}m$) showed to be higher than 50%. The particulate ranged from $10{\mu}m\;to\;2.5{\mu}m$ showed about 30-40%. PM2.5 was not scarcely detected in the samples collected for building demolition work using explosion. We conclude that the dust generated during building demolition work using explosion has not most respirable particulate.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.22 no.4
• /
• pp.345-352
• /
• 2012

1980년대 초 Sherwood교수가 한국에 와 있으면 당시 탄광의 호흡성먼지의 농도를 측정한 자료를 활용하여 로그-정규분포에 대한 분석을 한 자료이다. 탄광의 건조상태에서 농도는 물을 뿌리면서 하는 작업에 비해 매우 높은 수준을 보인다. 건조한 탄광에서 기하평균농도는 $26.1mg/m^{3}$이었고 물을 뿌린 탄광에서는 $4.1mg/m^{3}$이었다. 이는 매우 높은 수준이었음을 알 수 있다. 각 탄갱에서의 농도는 로그정규분포를 하였고 석탄을 접하는 탄갱에서의 농도는 $1.65mg/m^{3}$에서 $35mg/m^{3}$까지 다양하였다. 호흡성분진의 농도는 석탄을 접하는 탄갱에서 암석을 접하는 탄갱보다 높았는데 이는 분진의 원인이 석탄 때문이었다.

• Proceedings of the Safety Management and Science Conference
• /
• 2004.11a
• /
• pp.189-195
• /
• 2004

It compared quality characteristics for the stone surface treatment system and its products. With the result, the flame burner equipment was mainly used to the surface treatment of granite, but it occurred greatly the high temperature, the rock fragment, the noise and dust. For the other side, the whetstone polishing machine for the polishing was a maintenance for the specific physical properties of stone, and it did not occur the stone fragment and the dust. The durability of the stone products due to the flame burner was investigated with that it falls to $20\sim25\%$ more than the surface treatment by the whetstone polishing. Share's hardness of the polishing products in the durability test showed more greatly index than the flame burner and conventional product. The polishing products of Pochon stone in the case of the abrasion resistance showed great more $15\%$ than the general products, more $9\%$ than the products by the flame burner.

• Ocean and Polar Research
• /
• v.41 no.3
• /
• pp.169-181
• /
• 2019

The purpose of this study is to develop geochemical tracers to identify a specific source desert of mineral dust in China using the published data. In addition, we tested the applicability of these tracers to wet-deposits and soil samples collected in Jeju, Korea. Because of similarity in trace elemental compositions of mineral dust from the major arid regions in China, such as Taklimakan, West Ordos (Badain Jaran), East Ordos (Mu Us and Hobq), East Northern China (Horqin), West Northern China (Gurbantunggut), and Chinese Loess Plateau, there has been limited to the use of geochemical data for source identification. Here we propose the four (4) plots using combination of seven (7) geochemical variables as a source indicator to distinguish one from other source regions in China: $\frac{Y}{Tb_N}$ vs. $\frac{Th}{{\Sigma}REE_N}$, $\(\frac{La}{Gd}\)_N$ vs. $\frac{Y}{{\Sigma}REE_N}$, $\frac{Th}{Tb_N}$ vs. $\frac{Y}{Nd_N}$, and $\frac{Th}{Tb_N}$ vs. $\(\frac{Ce}{Ce}\)_N^*$, where $_N$ and $\(\frac{Ce}{Ce}\)_N^*$ stand for values normalized to Post-Archean Average Shale composition and Ce anomaly, respectively. Mineral dusts from aforementioned six major deserts are distinguished one from the others by the combined use of these variables. Jeju rock and soil samples form a separate domain from Chinese mineral dusts in all four plots. In contrast, most of Jeju dust samples were comparable with the West Ordos desert (Badain Jaran) domain, indicative of strong influence of Badain Jaran dust in Jeju in spring season when the mineral dust was collected. A weak positive Ce anomaly in Jeju samples implies minimal local contribution. Our study suggests that the combination of $\frac{Y}{Tb_N}$ vs. $\frac{Th}{{\Sigma}REE_N}$, $\(\frac{La}{Gd}\)_N$ vs. $\frac{Y}{{\Sigma}REE_N}$, $\frac{Th}{Tb_N}$ vs. $\frac{Y}{Nd_N}$, and $\frac{Th}{Tb_N}$ vs. $\(\frac{Ce}{Ce}\)_N^*$ can be used to identify a specific source region of mineral dust in China as well as Jeju mineral particles.