• Journal of the Korean GEO-environmental Society
• /
• v.14 no.8
• /
• pp.53-60
• /
• 2013

The compaction control method of national road substructure is using field density test to determine the relative compaction and plate bearing test to check the load bearing capacity. However, these two tests digitize a construction site manager's judgment based on his experience, so mechanical basis is weak. Resilient modulus method, which is recently being used to resolve such problem, is evaluated as a rational design method of pavement structure that can rationally reflect the stress-strain state of pavement materials that is caused by the condition of load repetition of vehicle load. However, the method of measuring the resilient modulus is difficult and lengthy, and it has many problems. To replace it, light falling weight test is recently being proposed as a simple test method. Therefore, this research uses dynamic plate loading test, which quickly and simply measures the elastic modulus of the subgrade and sub-base construction and site of maintenance, to judge the possibility of compaction control of the stratum under the road, and it proposes relation formula by analyzing the result of static load test.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.6
• /
• pp.97-107
• /
• 2013

On the Staggered Crosswalks, pedestrians cross the crosswalks two times. This method can reduce the cycle, the vehicle delay and the walking distance by increasing the major direction of green time. The safety of pedestrians is also effective. This study suggests the warrant of the facilities of island width and length etc. by considering the road structure and pedestrians. Also this study suggests the standard of the safety through the accident analysis of Staggered crosswalks and General Crosswalks. In the results, accident rate of the Staggered Crosswalks 18.3(100 million vehicle-km) was lower than the accident rate of the General Crosswalks 28.3(100million vehicle-km). By understanding the start point of crossing of the Staggered Crosswalks, the analysis of the location and types of accident suggests the safety zone(spare space). The setting warrants of Staggered Crosswalks are 4 lane over the road and the 2 meter over sidewalk width of island. The minimum length of the Pedestrian island was doubled compared to the crosswalks width. And the maximum length was set by considering the wait time of the pedestrians.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.2
• /
• pp.397-407
• /
• 2017

This study investigated current status of rest area for drowsy drivers on the highways and drew the related issues to define specifications and design criteria regarding expressway rest area for drowsy drivers on the highways. Based on the investigation result, geometric structure specifications and improvement plans are suggested. The entry part of a rest area for drowsy drivers on the highways was divided into deceleration transition section, deceleration lane and entry connection road while the exit part was divided into exit connection road, acceleration lane and acceleration transition section. The optimum length was estimated by considering the main lane vehicle traveling speed, traveling speed at the beginning/end point of entry/exit connection roads, deceleration and acceleration. In addition, reasonable design criteria were suggested by dividing the parking section of rest area for drowsy drivers according to parking style and cross-section composition, and length of parking space and then considering the ratio of vehicles using rest area for drowsy drivers, the ratio of heavy vehicles, and the design speed within a rest area for drowsy drivers. It is believed that the suggested design criteria on rest area for drowsy drivers on the highways can be utilized in the future planning and maintenance of rest area for drowsy drivers. Additionally, the defined criteria on installing rest area for drowsy drivers on the highways will prevent traffic accidents in resting facilities and highways as well as improve usage and safety of them.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.147-157
• /
• 2011

As a background study to apply the reliability-based resistance factors to the domestic concrete bridge design code, a comparative study is conducted for the design results and the reliability indexes obtained by adopting different resistance factor formats to yield the design strength of concrete structures. The design results which are calculated by applying the section resistance factors of the current domestic design code and the material resistance factors of Eurocode are compared for the concrete beam bridge. The reliability index is calculated by considering the uncertainties involved in material, dimension and strength equation during the design procedure to get the strength of concrete structure. Also, the sensitivity analysis is performed to figure out which design variables have great impact on the reliability index. The resistance factors of the current domestic bridge design code, AASHTO LRFD and Eurocode are applied to the bridge design for flexure and shear strength and the results show that the resistance factors of the domestic code give the largest reliability indexes. It is observed that the probabilistic distribution of the live load makes difference for the reliability index and the yield strength of reinforcing steel and the live load have great impact on the reliability of both flexural and shear strength of concrete beam through the sensitivity analysis.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.105-110
• /
• 2009

The On Line Electric Vehicles(OLEV) that can pick up inductive power from underground coils on driving with high efficiency have been developed this year, and is now proposed in this paper. The IPS(Inductive Power Supply) system consists of power supply inverters, power supply rails, pick up modules, and a regulator. There are 3 generations of IPS have been developed so far, and the $4^{th}$ generation IPS is being developed. The $1^{st}$ generation has been demonstrated this Feb. 27, which is equipped with mechanically auto tracking pick-up module with 1cm air gap, and showed 80% power efficiency. The $2^{nd}$ generation IPS applied to an 120kW (average)/240kW(peak) motor powered electric bus has 17cm air gap with 72% power efficiency. For the $2^{nd}$ generation IPS, the Power supply inverter has 440V, 3phase input and 200A @ 20kHz output. The test power supply rail of 240m long is segmented by 60m each, where newly developed core structure and power cable are constructed under the road covered with asphalt of 5cm thickness. The pick-up modules which consist of core, winding wire, and rectifiers are fixed to the bottom of the bus which can carry more than 40 passengers and can pick up max. 60kW. To remove parasitic component and to transfer maximum power between them resonant circuit topology is applied to the primary and secondary sides. The EMF level is below 62.5mG at 1.75m from the center of the road to meet the regulation. Several effective ways of reducing EMF levels have been developed. In addition, effective ways to solve problems related high frequency power cables buried in ground and it's proof from soil have been studied also. This development shows that the IPS system is capable of supplying enough power to the pick-up of OLEV and can reduce battery size, weight and cost, which means the IPS with OLEV is one of the best candidate for EV.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.4
• /
• pp.705-713
• /
• 2016

For the soft ground construction, the factors not considered in the design stage occurs in the construction stage so that they cause the increase of the construction cost due to the structural stability and the design change. The subject of the study is the construction section of the industrial complex access road made in the Ochang region of Chungcheongbuk-do. The study is concerned with selecting the soft ground handling method such as the replacement method using rock debris and the surcharge reflecting the service load as the soft ground handling measure and analyzing the effect of reducing the construction cost with the stability of structures and the reduction of the construction period. The soft ground in the study section consists of sandy and cohesive soil and is 2.4m to 5.5m deep. It is distributed unevenly between the 1.5m to 5.9m stratums under the ground surface. Settlement is not serious, but the future uneven settlement and difference are expected so that the future settlement behavior is estimated by analyzing the site measurement results after the soft ground treatment. Moreover, in consideration of the regional characteristics and economic efficiency, soil with good quality is replaced with rock debris as the replacement material so that 29% of the construction cost is reduced due to the increase of stability and the reduction of duration. If the estimation of the dispersion of the pore water pressure within the dam body and the change of the underground water level and the relation of the actually measured soft ground with consolidation is studied further on the basis of the study, it is expected that the behavior of the soft ground will be correctly estimated in various site conditions.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.6
• /
• pp.63-77
• /
• 2006

The research aim is to classify biotope types of rural eco-villages designed by ministry of environment and analyze landscape ecological characteristics of them. This information would provide information on eco-villages' potential and specific needs to improve landscape ecological structure of eco-villages. Two eco-villages, designated by ministry of environment, in Yoocheon-ri and Sanduk-ri were selected and the landscape ecological metrics used in this study were Area, Shannon diversity index, Shape index, Distance index. The results are as follows. 1) There were five biotope types in large-scale classification, 13 biotope types m Sanduk-ri and 9 biotope types in Yoocheon-ri in middle-scale classification, 31 biotope types in Sanduk-ri and 24 biotope types in Yoocheon-ri in small-scale classification. 2) In the case of area, artificial biotope types, such as artificial forest, agricultural irrigation canal, wet paddy, dry paddy and residential area, covered more than 80% of total area. However, natural biotope types, such as natural forest, river, reservoir, covered just more than 10% of total area. In details, an orchard (26.69%) was the dominant biotope type, followed by artificial forest (19.10%) in Sanduk-ri and the first most abundant biotope type was artificial forest (49.71%), followed by wet paddy (15.95%) in Yoocheon-ri. 3) The result of Shannon diversity index indicated that Sanduk-ri (2.158) had more heterogeneity landscape, rather than Yoocheon-ri (2.051). 4) In the case of shape index, road (13.09) had more complex and irregular shape than either agricultural irrigation canal (3.35) or artificial forest (2.46) in Sanduk-ri. Road (6.52) was also the most irregular biotope shape, followed by river (5.70) and agricultural irrigation canal (4.78) in Yoocheon-ri. 5) Mean Nearest-neighbour Distance (MND) was smallest in wet paddy and dry paddy biotope types in the two study area, suggesting that these biotope types were concentrated within these study areas. From the result, this research suggested information to protect and improve biotopes of eco-villages in the landscape ecological terms. To achieve this improvement plan, there should be strong support by ministry of environment and local governments.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.05a
• /
• pp.157-164
• /
• 2005

Urban conditions such as underground facilities and ambient noises due to cultural activity restrict the application of conventional geophysical techniques in general. We used the refraction microtremor (REMI) technique as an alternative way to get the geotechnical information, in particular shear-wave (S-wave) velocity information, at a site along an existing rail road. The REMI method uses ambient noises recorded using standard refraction equipment to derived shear-wave velocity information at a site. It does a wavefield transformation on the recorded wavefield to produce Rayleigh wave dispersion curve, which are then picked and modeled to get the shear-wave velocity structure. At this site the vibrations from the running trains provided strong noise sources that allowed REMI to be very effective. REMI was performed along the planned new underground rail tunnel. In addition, Suspension PS logging (SPS) were carried out at selected boreholes along the profile in order to draw out the quantitative relation between the shear wave velocity from the PS logging and the rock mass rating (RMR) determined from the inspection of the cores recovered from the same boreholes, These correlations were then used to relate the shear-wave velocity derived from REMI to RMR along the entire profile. The correlation between shear wave velocity and RMR was very good and so it was possible to estimate the RMR of the total zone of interest for the design of underground tunnel,

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.6
• /
• pp.63-70
• /
• 2011

A bicycle is different from vehicles in the structure that a rider is fully exposed to the surrounding environment. Therefore, it needs to make use of prior information about local weather, air quality, trail road condition. Moreover, since it depends on human power for moving, it should acquire route property such as hill slope, winding, and road surface to improve its efficiency in everyday use. Recent mobile applications which are to be used during bicycle riding let us aware of the necessity of development of intelligent bicycles. This study aims to develop a riding state (up-hill, down-hill, accelerating, braking) recognition algorithm using a low-power wrist watch type embedded system which has 3-axis accelerometer and wireless communication capability. The developed algorithm was applied to 19 experimental riding data and showed more than 95% of correct recognition over 83.3% of the total dataset. The altitude and temperature sensor also in the embedded system mounted on the bicycle is being used to improve the accuracy of the algorithm. The developed riding state recognition algorithm is expected to be a platform technology for intelligent bicycle interface system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.725-732
• /
• 2017

Weight reduction is one of the important issues in the automotive industry and the development of internal combustion engines vehicles, future vehicles, and eco-friendly vehicles for improving fuel efficiency. The objective of this study is to investigate the improvement of driving performance by weight reduction and optimum design for a formula-type self-designed on-road vehicle. This study is divided into the four steps. Firstly, the engine room was replaced and designed with a lighter engine. Secondly, an optimization study was conducted to simplify and lighten the vehicle components with the design of the frame. Thirdly, the structure design was optimized and the suspension was analyzed with the design of the frame. Finally, the design of an upright and hub with reduced weight was carried out using lighter parts. As a result, we reduced the weight of the vehicle by 48.5kg compared to the previous year (19.5%) and increased the acceleration from 6.8 s to 5.8 s.s.