• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.371-378
• /
• 2015

In this paper, a different type of pulse width modulation (PWM) control scheme for a buck converter is introduced. The proposed buck converter uses PWM with frequency hopping and a low quiescent.current low dropout (LDO) voltage regulator with a power supply rejection ratio enhancer to reduce high spurs, harmonics and output voltage ripples. The low quiescent.current LDO voltage regulator is not described in this paper. A three-bit binary-to-thermometer decoder scheme and voltage ripple controller (VRC) is implemented to achieve low voltage ripple less than 3mV to increase the efficiency of the buck converter. An internal clock that is synchronized to the internal switching frequency is used to set the hopping rate. A center frequency of 2.5MHz was chosen because of the bluetooth low energy (BLE) application. This proposed DC-DC buck converter is available for low-current noise-sensitive loads such as BLE and radio frequency loads in portable communications devices. Thus, a high-efficiency and low-voltage ripple is required. This results in a less than 2% drop in the regulator's efficiency, and a less than 3mV voltage ripple, with -26 dBm peak spur reduction operating in the buck converter.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.507-515
• /
• 2013

This paper proposes a compensation method for the $2^{nd}$-order harmonic of single-phase grid-connected wind power generation systems. Theoretically, a single-phase grid-connected inverter system has no choice but to cause the $2^{nd}$-order harmonic to DC-link voltage. The reference active current is affected by the DC-link voltage. The output current from the reference active current is distorted by the $1^{st}$ and $3^{rd}$-order harmonic. The proposed method can compensate, conveniently, the reference active current with the $2^{nd}$-order harmonic. To reduce the $2^{nd}$-order ripple in the reference active current, proposed method takes a PR controller as a feed-forward compensator. PR controllers can implement selective harmonic compensation without excessive computational requirements; the use of these controllers simplifies the method. Both the simulation and experimental results agree well with the theoretical analysis.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.3
• /
• pp.1137-1145
• /
• 2017

This paper proposes the dead time effect compensation algorithm using proportional resonant controller in pulse width modulation inverter of motor drive. To avoid a short circuit in the dc link, the dead time of the switch device is surely required. However, the dead time effect causes the phase current distortions, torque pulsations, and degradations of control performance. To solve these problems, the output current including ripple components on the synchronous reference frame and stationary reference frame are analyzed in detail. As a results, the distorted synchronous d-and q-axis currents contain the 6th, 12th, and the higher harmonic components due to the influence of dead time effect. In this paper, a new dead time effect compensation algorithm using proportional resonant controller is also proposed to reduce the output current harmonics due to the dead time and nonlinear characteristics of the switching devices. The proposed compensation algorithm does not require any additional hardware and the offline experimental measurements. The experimental results are presented to demonstrate the effectiveness of the proposed dead time effect compensation algorithm.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1104-1107
• /
• 2019

This paper proposes a DC-DC boost converter for wearable AMOLED display using dead time controller to reduce dead time and improve power efficiency. Also the DC-DC boost converter adopts PWM-SPWM (set-time variable pulse width modulation) dual-mode to enhance power efficiency under light load and decrease output voltage ripple. The proposed circuit has been designed using $0.18{\mu}m$ BCDMOS process. Simulation results show that the circuit has power efficiency of 39%~96% and output ripple voltage of 2 mV under load current range of 1 mA~70 mA. The power efficiency of the proposed circuit is up to 2% higher than the previous PWM-SPWM method and up to 8% higher than only PWM method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.4
• /
• pp.278-284
• /
• 2009

This paper presents a firing angle controller of a thyristor converter for DC power supply using PID controller with parallel data loop to improve the dynamic response. The proposed parallel data loop for firing angle controller of 3-phase semi-converter, generates pre-measured firing angle according to reference voltage and load current. With the approximated firing angle according to operating conditions, the output voltage can fast keep the reference value with small voltage error. And the PID controller compensates the output voltage error from the firing angle of parallel data loop. In order to reduce the sudden changing of the data from current ripple, a simple digital low pass filter is used to determine the output data. The proposed control scheme is verified by the experimental test of a practical 50[A] grade thyristor converter system.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.198-200
• /
• 2018

In this paper a single-stage single-phase differential type isolated AC-DC converter is proposed. This converter eliminates the requirement to use bulky electrolytic capacitor from the system and at the same time provides DC charging by employing the AC Power Decoupling waveform control method. All the switches of the converter achieve ZVS turn on during half line cycle and all diodes achieve ZCS turn off during entire line cycle. A conventional controller is implemented for PFC control and output regulation, whereas a power decoupling controller is added to compensate $2^{nd}$ harmonic ripple power. In addition, an interleaving technique is applied to increase the power range of the converter and reduce the input inductor size. In the end simulation verification is performed and results are obtained for 6.6KW.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1123-1125
• /
• 2002

In this paper, interleaved boost converter is applied as a pre-regulator in switch mode power supply. Interleaved Boost Power Factor Preregulator (IBPFP) can reduce input current ripple as a simple voltage control loop only without inner current loop, because input current is divided each 50% by two switching devices. IBPFP can be classified as three cases from duty ratio condition in continuous current mode and be carried out state space averaging small signal modeling. According to modeling, the PID controller is applied and voltage control loop is constructed for suitable design condition. From frequency domain analysis, it is verified that control system is satisfied with design condition of switch mode power supply.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.283-287
• /
• 1989

This paper presents a microprocesser based Self-Controller for a Permanent Magnet Synchronous Motor(PMSM), fed by voltage soure inverter. The proper operation of the PMSM can be ensured only if the stator current is always synchronized with the its Back-E.M.F. The use of incremantal encoder with high resolution makes it possible to design a Self-Control led P.W.M. inverter. The pulse ratios are controlled to reduce the torque ripple in the low-speed drive region. And during the operation, torque - speed characteristics are improved by the control of optimal load angle.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.42-44
• /
• 2005

The motor research of pre-existing attaches importance about one and three motor of reduce torque ripple and speed control. 3-Phase PMSM Motor, which is generally used, has limited usage in high speed, due to pulsation torque and variable speed. To solve this problem it is necessary to increase invariable, pole number or the number of slots. In this paper 7-Phase PMSM Motor of Steady state analysis of Torque and Output Voltage characteristic.7-Phase modulation method with Space Voltage Vector is studied for ideal operation of controller.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.496-499
• /
• 2006

The solar cells should be operated at the maximum power point because its output characteristics are greatly fluctuate on the variations of insolation, temperature and loads. To obtain maximum power from solar cell, photovoltaic system cell power system usually requires maximum power point tracking controller. This paper propose Maximum power point tracking method using zero slope of differential value of maximum power. The power compare method traces to maximum power point rapidly but oscillate on the maximum power point largely, when quantity insolation variation is big. The power compare method is traces to maximum power point slowly but oscillate maximum point on the maximum power point smally, when quantity insolation variation is small. To solve two problem of the power compare method, designed zero slope of differential value of maximum power.