• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.6
• /
• pp.105-110
• /
• 2012

In this paper, A planar UWB antenna with notched WLAN band, 802.11a band (5.15 ~ 5.825GHz), by using slot and slit is designed by using CST Microwave Studio. The notched bandwidth can be controlled by the length and width of the slot and slit in the patch and ground plane and it's radiation characteristics are examined through the experiments. The bandwidth based on the -10dB return loss level can be covered the full UWB band (3.1 ~ 10.6GHz) with a notched WLAN band (5.147 ~ 5.83GHz). Also, the experimental radiation pattern is almost omnidirectional in the H-plane.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.308-315
• /
• 2002

In this paper, the 5-bit digital phase shiftier with 10 InGaAs HEMTs is designed and fabricated for U.S. mobile DBS receiving active phased array antenna system in 12 GHz band. 11.25 $^{\circ}$, 22.5$^{\circ}$ and 45$^{\circ}$ phase bits are designed in leaded-line type. 90$^{\circ}$ and 180$^{\circ}$ phase bits are designed in reflection type combined with ring hybrid. The return loss more than 17.5 ㏈, insertion louts less than 7.8 ㏈, and maximum phase error of $\pm$6$^{\circ}$for 32 phase responses are measured in 12.2 GHz~ 12.7 GHz band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.173-181
• /
• 2011

In this paper, we propose a half mode substrate integrated waveguide(HMSIW) balanced bandpass filter to yield improved isolation between output ports. In order to achieve good isolation, resistive coupling slot is employed in HMSIW filter. The measurement results show that the insertion losses($S_{21}$, $S_{31}$) are $5.4{\pm}0.2$ dB and input return loss($S_{11}$) is more than 10 dB from 5.8 GHz to 6.4 GHz. Moreover isolation between output ports is larger than 18 dB and phase difference of output ports is $180{\pm}10^{\circ}$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.3 s.333
• /
• pp.33-38
• /
• 2005

In this paper, we have designed and fabricated a hybrid ring coupler to prove the fabrication possibility of various passive components, applying millimeter wave using newly proposed transmission lines, i.e. BAMLs. The characteristics of the fabricated hybrid ing coupler were a the S31(coupling) of 3.58 dB, the S21(thru) of 3.31 dB at the 60 GHz center frequency, the S11(return loss) over 16.17 dB, S41(isolation) over 55 dB at 61 GHz, and the phase difference between port 2 and port 3 of $180{\pm}loat$ 60GHz. In order to reduce the size of hybrid ring coupler, we designed the hybrid ring coupler which inserts a slow wave structure. With this structure, we were able to reduce the hybrid ring coupler by $33\%$ area.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.568-575
• /
• 2011

In this paper, we propose a small broadband antenna for mobile device. The proposed antenna consists of a printed rectangular monopole antenna and a parastic element connected to ground using narrow meander line and it is designed on a FR-4 substrate that has a thickness of 0.8 mm and a dielectric constant of 4.4. The FR-4 substrate's size is 50 mm${\times}$90 mm comparable to the real mobile device. The fabricated antenna's size is 12.5 mm${\times}$10.5 mm${\times}$0.8 mm and the measurement shows -10 dB return loss bandwidth of 2,200~6,000 MHz and gains of 2.86~4.01 dBi. Accordingly, the proposed antenna can support mobile device for WiBro(2,300~2,380 MHz), WLAN(IEEE 802.11b/g/n: 2,400~2,480 MHz, IEEE 802.11a: 5,150~5,825 MHz), and mobile WiMAX(IEEE 802.16e : 2,500~2,690 MHz, 3,400~3,600 MHz) service bands.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.6
• /
• pp.1287-1292
• /
• 2012

In this paper, a dual polarization patch antenna operates at the wide bandwidth of 1.525GHz~1.665GHz was designed and fabricated. To obtain the wide bandwidth and high gain, increased height of air floor from GND was applied, and to get wide band axial ratio and high gain, parasitic patch was applied. The simulation and measurement showed good agreements, the VSWR was less than 1.9 at the frequency bandwidth, the return loss was less than -10dB, and the LHCP(Left Hand Circular Polarization) and RHCP(Right Hand Circular Polarization) isolation was less than -13dB at the frequency bandwidth.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.176-181
• /
• 2013

This paper presents a CMOS impulse radio ultra-wideband (IR-UWB) receiver implemented using IBM 0.13um CMOS technology for inner/inter-chip wireless interconnection. The IR-UWB receiver is based on the non-coherent architecture which removes the complexity of RF architecture (such as DLL or PLL) and reduces power consumption. The receiver consists of three blocks: a low noise amplifier (LNA) with active balun, a correlator, and a comparator. Simulation results show the die area of the IR-UWB receiver of 0.2mm2, a power gain (S21) of 12.5dB, a noise figure (NF) of 3.05dB, an input return loss (S11) of less than -16.5dB, a conversion gain of 18dB, a NFDSB of 22. The receiver exhibits a third order intercept point (IIP3) of -1.3dBm and consumes 22.9mW of power on the 1.4V power supply.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.49-57
• /
• 2000

In this paper, lumped-element isolator is analyzed and designed using the scattering matrix approach. Using the designed parameters, compact isolator with 7.0x7.0x2.3 mm$^3$ dimensions is fabricated and tested in 1.765GHz PCS phone band. Implemented isolator shows 29.95dB isolation characteristic at center frequency and has 0.35dB insertion loss in overall 30MHz operating bandwidth. Return losses of input and output port are measured below -19 dB. Experimental results show that the implemented isolator has better performances than the conventional one.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.2 s.332
• /
• pp.75-80
• /
• 2005

In this paper, 2-stage power amplifier has been designed for 5.8GHz wireless LAN application. The power amplifier PldB output power has 21.6dBm at 5.8GHz frequency. Also the power amplifier shows 17.6dB gain and -17.8dB input return loss at 5.725GHz to 5.825GHz. The OFDM modulation and transmission block have been modeled in order to analyse the relationship between the power amplifier distortion and output ACPR for the IEEE 802.11a wireless LAN. The nonlinear characteristic of the power amplifier has been modeled as AM-to-AM and AM-to-PM using the behavioral model, and the output spectrum is analysed with the phase distortion variation. Also, amplifier back-off value from PldB to satisfy the required IEEE 802.11a standard spectrum mask has been simulated with phase distortion, and the simulation data have been compared to the measurement result collected by using the pre-distortion technique.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.980-986
• /
• 2001

Bragg reflector type FBAR was fabricated on the Si(100) substrate. We measured a frequency response of the resonator at 5.2 GHz and analyzed it by numerical calculation considering actual acoustic losses of each layer in the structure. We fabricated nine layer Bragg reflector of W-SiO$_2$pairs using r.f. sputtering method and fabricated AlN piezoelectric and Al electrodes using pulsed dc sputtering. The return loss(S$_{11}$) of the fabricated Bragg reflector type FBAR was 12 dB at 5.38 GHz and the series resonance frequency(f$_{s}$) was 5.376 GHz and the parallel resonance frequency(f$_{p}$) was 5.3865 GHz. Effective electro-mechanical coupling constant (K$_{eff{^2}}$) and Quality factors(Q$_{s}$), the Figures of Merit of the resonator, were about 0.48% and 411, respectively. We extracted acoustic parameters of AlN piezoelectric and reflection coefficient of the Bragg reflector by numerical calculation. We could know that material acoustic impedance and wave velocity of AlN piezoelectric decreased for intrinsic value and the electromechanical coupling constant(K$_2$) value was very low owing to the poor quality of the AlN piezoelectric. Reflection coefficient of Bragg reflector was 0.99966 and reflection band was very wide from 2.5 to 9.5 GHz.