• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.303-306
• /
• 2005

This paper presents the frequency-dependent characteristics of leakage currents flowing through ZnO surge arrester block. The leakage current-voltage (I-V) characteristic curves of the commercial ZnO surge arrester blocks were measured. The resistive leakage current was found to increase with increasing frequency in the low conduction region. The capacitance of ZnO block was independent of the magnitude and frequency of the applied voltage. The power losses of ZnO block increase as the frequency of applied voltage increases, because of the dielectric loss related to the frequency of the test voltage.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.822_823
• /
• 2009

Superconducting fault current limiters (SFCLs) provide one of the most effective solutions to cope with enormous increase of fault current level. The 13.2 kV/ 630 A class resistive SFCL using coated conductor (CC) was developed and its short-circuit test was successful. Successful commercialization of the SFCL requires that no loss is produced by impedance of limiting coil during normal operation. Since the limiting coil consists of inner layer and outer layer, gap length between the layers is an important parameter to analyze the electromagnetic characteristics of coil. This paper deals with the electromagnetic characteristics of coil according to gap length through the simulation and analysis in comparison with experiment results.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.14 no.2
• /
• pp.89-95
• /
• 1978

A SCR static breaker was studied on the Resistive and inductive load, then on the overload break circuit using operational Amplifier. In this paper, the principal circuit required for forced commutation was voltage commutation by the introduction of a parallel Capacitor. The results obtained are follows; 1. In thecondition that the tima constant of R-C circuit is larger than the turn off time of SCR, the breaker has low transient phenomena and no recovery vol age. 2. By using OP Amplifier on the load circuit, overcurrent trip point will be able to adjust to the wide range of over current. 3. In the over current qrcuit, the power loss was reduced remarkably.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.609-618
• /
• 2013

This paper proposes a primary side constant power control scheme for TRIAC dimmer compatible LED drivers. The LED driver is a Flyback converter operated in boundary conduction mode (BCM) to minimize the switching loss. With the proposed control scheme, the input power of the Flyback converter can be controlled by the TRIAC dimming angle, which is not affected by AC input voltage variations. Since the output voltage is almost constant for LED loads, the output current can be changed by controlling the input power with a given conversion efficiency. The isolated feedback circuit is eliminated with the proposed primary side control scheme, which dramatically simplifies the whole circuit. In addition, the input current automatically follows the input voltage due to the BCM operation, and the resistive input characteristic can be achieved which is attractive for TRIAC dimming applications. Experimental results from a 15W prototype verify the theoretical analysis.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.146-148
• /
• 2003

SrZrO$_3$ resistive oxide barriers on Ag sheathed Bi2223 monocore tapes were prepared by the sol-gel and dip coating method to reduce AC coupling loss. The performance of the dip-coated SrZrO$_3$ thin films was evaluated in terms of bond strength and surface microstructure by varying the amount of PVP (polyvinylpyrrolidone) binder. Although bond strength and coating thickness increased as the PVP content rose, surface microcracking was more severe for the specimen containing higher content of PVP binder. It suggests that coating thickness and microcracking of the SrZrO$_3$ films on Bi2223 tapes was governed primarily by the amount of PVP binder.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.3
• /
• pp.291-294
• /
• 2003

A highly interferent-resistive membrane, poly-5-amino-1-naphthol (poly-5A1N), underlied beneath enzymeembedded poly-1,3-phenylendiamine (poly-m-PD) network for miniturized continuous monitoring glucose sensors. The enzyme layer was prepared from a mixed solution of glucose oxidase (GOx) and m-PD monomer by simple electrolysis. The mass change of poly-5A1N was monitored by electrochemical quartz crystal microbalance (EQCM) in situ and the corresponding thickness was measured. Successive electropolymerization of poly-5A1N and poly-m-PD create a several tens nm-thick bilayer showing excellent selectivity for $H_2O_2$ and low activity loss of immobilized enzymes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.104-105
• /
• 2013

The buildings constructed with steel structure is coated with certified fire resistive material to resist from fire. Coating materials lose their initial performances as time passes, so they need some maintenance. Fireproof spray-application also loses its performance and this performance loss of thr fireproof spray-application is very important because fire resistance of buildings depends on fireproof spray-application. So this study is to develop Acceleration durability test method of Fireproof spray-application, and use the Certification of fire resistant coating system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.4
• /
• pp.369-375
• /
• 2015

In this paper, transparent circuit analog radar absorbing structure with angular stability for stealth aircraft canopy was proposed and designed. To obtain wideband electromagnetic absorption, optical transparency and smaller thickness, we proposed the novel FSS(Frequency Selective Surface) for X-band and implemented the resistive FSS and PEC(Perfect Electric Conductor) plane using ITO(Indium Thin Oxide) coating with optical transmissivity of 90 %. Reflection loss characteristics for different incident angles of both TE(Transverse Electric) and TM(Transverse Magnetic) polarizations are presented through simulations. We then fabricated the proposed structure to verify the simulation results. The comparisons between the simulation and measured results show good agreements. The results also show that the proposed radar absorbing structure can provide better frequency stability for different incidence angles and polarizations as well as optical transparency. We can apply this proposed structure to the canopy of stealth aircraft and other stealth applications for visible transparency.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.687-689
• /
• 2003

Recently, issues regarding environment and the diversification of dependence in oil are watched with keen interest. Wind power attracts most interest because of its high-energy efficiency with environment friendly functions. The paper discusses the development of a coreless axial-flux permanent magnet (AFPM) generator for a wind power system. Analyzed the Coreless AFPM generator by electromagnetic, and designed wind power generator with this. The 3 phase output of stator is rectified and fed to a common do link. The overall machine structure has high compactness and lightness, because of the lack of the iron core. The test results with a resistive load confirm the satisfactory operation of generator. Compared with conventional generator, the design has lower weight, lower Power loss and improved efficiency.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2166-2168
• /
• 2005

This paper presents the frequency - dependent characteristics of leakage currents flowing through ZnO varistor. The leakage current - voltage (V-I) characteristic curves of the commercial ZnO varistor were measured. The resistive leakage current was increased with increasing the magnitude and frequency of the applied voltage in the low conduction region. The power losses of ZnO varistor increase as the frequency of applied voltage increases, because of the dielectric loss related to the frequency of the test voltage.