• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.301-306
• /
• 2015

An ultra-compact and wideband low noise amplifier (LNA) in a quad flat non-leaded (QFN) package is presented. The LNA monolithic microwave integrated circuit (MMIC) is implemented in a $0.25{\mu}m$ GaN IC technology on a Silicon Carbide (SiC) substrate provided by Triquint. A source degeneration inductor and a gate inductor are used to obtain the noise and input matching simultaneously. The resistive feedback and inductor peaking techniques are employed to achieve a wideband characteristic. The LNA chip is mounted in the $3{\times}3-mm^2$ QFN package and measured. The supply voltages for the first and second stages are 14 V and 7 V, respectively, and the total current is 70 mA. The highest gain is 13.5 dB around the mid-band, and -3 dB frequencies are observed at 0.7 and 12 GHz. Input and output return losses ($S_{11}$ and $S_{22}$) of less than -10 dB measure from 1 to 12 GHz; there is an absolute bandwidth of 11 GHz and a fractional bandwidth of 169%. Across the bandwidth, the noise figures (NFs) are between 3 and 5 dB, while the output-referred third-order intercept points (OIP3s) are between 26 and 28 dBm. The overall chip size with all bonding pads is $1.1{\times}0.9mm^2$. To the best of our knowledge, this LNA shows the best figure-of-merit (FoM) compared with other published GaN LNAs with the same gate length.

• 한국항행학회논문지
• /
• 제12권6호
• /
• pp.604-610
• /
• 2008

본 논문은 지그비(ZigBee) 응용을 위한 2.4 GHz CMOS RF 프론트-엔드(front-end) 설계에 관한 기술이다. Front-End는 저잡음 증폭기(LNA), 주파수 변환기(Mixer)로 구성 되며, 2 MHz의 중간 주파수 (IF : intermediate frequency)를 사용 한다. LNA는 피드백저항을 사용한 Common-Source(CS with resistive feedback) 구조와 축퇴(degeneration) 인덕터를 사용 하였고, 20db의 전압 이득을 디지털신호로 조절할 수 있다. Mixer는 저전류 소모를 고려하여 수동(passive) 구조로 설계하였다. RF front-end는 $0.18{\mu}m$ 1P6M CMOS 공정을 이용하여 구현하였으며 1.8V의 전압으로부터 3.28 mA의 전류 소모를 하며 측정 결과 NF는 4.44 dB, IIP3는 -6.5 dBm을 만족시킨다.

• Smart Structures and Systems
• /
• 제7권1호
• /
• pp.1-13
• /
• 2011

It has been shown in the literature that active adjustment of the intake area of a jet engine has potential to improve its fuel efficiency. This paper presents the design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators. The Nitinol SMA material is used in this research due to its advantages of high power-to-weight ratio and electrical resistive actuation. The Nitinol SMA material can be fabricated into a variety of shapes, such as strips, foils, rods and wires. In this paper, SMA wires are used due to its ability to generate a large strain: up to 6% for repeated operations. The proposed proof-of-concept engine intake employs overlapping leaves in a concentric configuration. Each leaf is mounted on a supporting bar than can rotate. The supporting bars are actuated by an SMA wire actuator in a ring configuration. Electrical resistive heating is used to actuate the SMA wire actuator and rotate the supporting bars. To enable feedback control, a laser range sensor is used to detect the movement of a leaf and therefore the radius of the intake area. Due to the hysteresis, an inherent nonlinear phenomenon associated with SMAs, a nonlinear robust controller is used to control the SMA actuators. The control design uses the sliding-mode approach and can compensate the nonlinearities associated with the SMA actuator. A proof-of-concept model is fabricated and its feedback control experiments show that the intake area can be precisely controlled using the SMA wire actuator and has the ability to reduce the area up to 25%. The experiments demonstrate the feasibility of engine intake area control using an SMA wire actuator under the proposed design.

• 한국위성정보통신학회논문지
• /
• 제9권2호
• /
• pp.7-11
• /
• 2014

본 논문에서는 $0.5{\mu}m$ p-HEMT 공정을 이용한 MMIC 주파수 혼합기를 설계하였다. 본 주파수 혼합기는 Local 신호전력이 -4 ~ 4 dBm에서 유사한 성능을 갖도록 설계하여 local 신호의 변화에 따른 변환 성능이나 선형 성능이 일정하게 유지 되도록 하였다. 이와 같은 특성을 갖도록 하기 위해 새로운 형태의 FET를 이용한 피드백 회로를 구성하여, LO신호전력의 변화에 따른 성능 변화를 최소화 하였으며 넓은 주파수 대역에서 사용 할 수 있는 MMIC 주파수 혼합기 성능을 얻었다. 설계결과 LO신호전력이 -4 ~ 4dBm일 때, 0.5 ~ 2.6GHz의 주파수 범위에서 변환손실이 6 dB에 IIP3가 30 dBm 이상의 우수한 성능을 갖는 설계 결과를 얻었다.

• Journal of Semiconductor Engineering
• /
• 제2권1호
• /
• pp.109-118
• /
• 2021

This review paper describes the overall operating principle of a discrete-time delta-sigma modulator (DTDSM) and a continuous-time delta-sigma modulator (CTDSM) using a switched-capacitor (SC). In addition, research that has solved the problems related to each delta-sigma modulator (DSM) is introduced, and the latest developments are explained. This paper describes the chopper-stabilization technique that mitigates flicker noise, which is crucial for the DSM. In the case of DTDSM, this paper addresses the problems that arise when using SC circuits and explains the importance of the operational transconductance amplifier performance of the first integrator of the DSM. In the case of CTDSM, research that has reduced power consumption, and addresses the problems of clock jitter and excess loop delay is described. The recent developments of the analog front end, which have become important due to the increasing use of wireless sensors, is also described. In addition, this paper presents the advantages and disadvantages of the three-opamp instrumentation amplifier (IA), current feedback IA (CFIA), resistive feedback IA, and capacitively coupled IA (CCIA) methods for implementing instrumentation amplifiers in AFEs.

• 전기학회논문지
• /
• 제60권12호
• /
• pp.2286-2292
• /
• 2011

In this paper we present the design of Low Noise Amplifier(LNA), mixer and filter for RF front-end part of partial discharge monitoring system. The monitoring system of partial discharge in high voltage power machinery is used to prevent many kinds of industrial accidents, and is usually composed of three parts - sensor, RF front-end and digital microcontroller unit. In our study, LNA, mixer and filter are key components of the RF front-end. The LNA consists of common gate and common source-cascaded structure and uses the resistive feedback for broad band matching. A coupled line structure is utilized to implement the filter, of which size is reduced by the meander structure. The mixer is designed using dual gate structure for high isolation between RF and local oscillator signal.

• 로봇학회논문지
• /
• 제12권3호
• /
• pp.356-364
• /
• 2017

This paper presents a force control based on the observer without taking any force or torque measurement from the robot which allows realizing more stable and robust human robot interaction for the developed multi-functional upper limb rehabilitation robot. The robot has four functional training modes which can be classified by the human robot interaction types: passive, active, assistive, and resistive mode. The proposed observer consists of internal disturbance observer and external force observer for distinctive performance evaluation. Since four training modes can be quantitatively identified as impedance variation, position-based impedance control with feedback and feedforward controller was applied to the assistive training mode. The results showed that the proposed sensorless observer estimated cleaner and more accurate force compared to the force sensor and the impedance controller embedded with the proposed observer completed the assistive training mode safely and properly.

• Journal of Power Electronics
• /
• 제13권4호
• /
• pp.609-618
• /
• 2013

This paper proposes a primary side constant power control scheme for TRIAC dimmer compatible LED drivers. The LED driver is a Flyback converter operated in boundary conduction mode (BCM) to minimize the switching loss. With the proposed control scheme, the input power of the Flyback converter can be controlled by the TRIAC dimming angle, which is not affected by AC input voltage variations. Since the output voltage is almost constant for LED loads, the output current can be changed by controlling the input power with a given conversion efficiency. The isolated feedback circuit is eliminated with the proposed primary side control scheme, which dramatically simplifies the whole circuit. In addition, the input current automatically follows the input voltage due to the BCM operation, and the resistive input characteristic can be achieved which is attractive for TRIAC dimming applications. Experimental results from a 15W prototype verify the theoretical analysis.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.127-130
• /
• 2004

In this paper, active shape control of composite structure actuated by shape memory alloy (SMA) wires is presented. Hybrid composite structure was established by attaching SMA actuators on the surfaces of graphite/epoxy composite beam using bolt-joint connectors. SMA actuators were activated by phase transformation, which induced by temperature rising over austenite finish temperatures. In this paper, electrical resistive heating was applied to the hybrid composite structures to activate the SMA actuators. For faster and more accurate shape or deflection control of the hybrid composite structure, PID feedback controller was designed from numerical simulations and experimentally applied to the SMA actuators.

• 로봇학회논문지
• /
• 제17권2호
• /
• pp.230-237
• /
• 2022

A technology that allows users to feel the elasticity of fabric through force feedback in the fashion and textile fields is very helpful to related manufacturing and sales areas. Currently bundle of fabrics, so called Swatch, is the only available way for the designer, manufacturer and the end-user to feel the fabrics. Images and video clips provide only visual characteristics, hence touch and stiffness are also very important characteristics to check beforehand. A study is conducted on a haptic device, which estimates the amount of change in the length of the virtual fabric and generates resistive force so that the user could feel the fabric stiffness. Since cables that can only transmit the tensile force are used, a force realization method is proposed, and it is verified numerically and experimentally.