• Corrosion Science and Technology
• /
• v.11 no.6
• /
• pp.247-256
• /
• 2012

Harmonic current was measured for a dummy cell with various values of resistance, and the procedure developed through the measurements was applied to the investigation of effects of the amplitude of applied frequency and applied potential on the harmonic current of a stainless steel and a carbon steel in chloride containing solutions. From the measurements of harmonic current in the dummy cell, the optimum values of applied frequency and applied potential in harmonic current measurements were found to be 1 mHz and 20 mV (or lower), respectively. Increase in harmonic current with applied frequency was observed in the case where the level of harmonic current is low as in a stainless steel. Decrease in polarization resistance was also noted in this corrosion system with either increasing applied frequency or decreasing applied potential. However, no obvious effects of applied frequency was observed on harmonic current and polarization resistance in a carbon steel in which the level of harmonic current is high.

• Journal of Microbiology
• /
• v.41 no.1
• /
• pp.16-21
• /
• 2003

We have collected eight high-level streptomycin-resistant strains of Pseudomonas marginalis and P. syringae pv. actinidiae which were isolated from kiwifruit orchards in Korea and Japan, The molecular mechanisms of resistance were investigated by the PCR, susceptibility tests, and nucleotide sequence analysis. Of the eight high-level streptomycin-resistant strains, four harbored strA-strB genes, which encode streptomycin-inactivating enzymes. While the three Korean strains of R marginalis did not have plasmid and carried the resistant genes in the chromosomes, the Japanese strain of P. syringae pv. actinidiae had a plasmid containing strA-strB genes. The myomycin susceptibility test demonstrated that the high-level resistance to streptomycin of the remaining four strains is associated with mutations in the rpsL gene. Nucleotide sequence analyses revealed that they contain a single base-pair mutation in codon 43 of their rpsL gene.

• Steel and Composite Structures
• /
• v.27 no.2
• /
• pp.243-253
• /
• 2018

In recent years, concrete-filled box or tubular columns have been commonly used in high-rise buildings. However, a number of fire test results show that there are significant differences between high strength concrete (HSC) and normal strength concrete (NSC) after being subjected to high temperatures. Therefore, this paper presents an investigation on the fire resistance of HSC filled steel tubular columns (CFTCs) under combined temperature and loading. Two groups of full-size specimens were fabricated to consider the effect of type of concrete infilling (plain and reinforced) and the load level on the fire resistance of CFTCs. Prior to fire test, a constant compressive load (i.e., load level for fire design) was applied to the column specimens. Thermal load was then applied on the column specimens in form of ISO 834 standard fire curve in a large-scale laboratory furnace until the set experiment termination condition was reached. The results demonstrate that the higher the axial load level, the worse the fire resistance. Moreover, in the bar-reinforced concrete-filled steel tubular columns, the presence of rebars not only decreased the spread of cracks and the sudden loss of strength, but also contributed to the load-carrying capacity of the concrete core.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.1
• /
• pp.59-67
• /
• 2002

The comparison of $J_{Rice}$-resistance considering a few strength ratio in Rice J-integral formula and $J_{\delta}$-resistance curves converted from experimental CTOD using appropriate strength chosen according to strain hardening level, n=10.6 (A533B steel) and n=8.1 (BS4360 steel) is carried out. The optimal dimensionless strength ratio like the factor of revision, (see full text)reflecting strain hardening level in Rice\`s experimental formula is found out and the reliability of appropriate reference strength chosen according to strain hardening level in different materials is investigated through doing that CTOD is transformed from $J_{\delta}$-integral using relationship between J-integral and CTOD. The results are as follows; 1) The optimal factor of revision is when m equals to 3 in (see full text) for Rice's and the above optimal factor of revision multiplies by coefficient, η in Rice's experimental formula instead of n=2, 2) and the pertinent reference strength for high strain hardening material like BS4360 steel is ultimate strength, $\sigma_{u}$ and for material like A533B steel is ultimate-flow strength, $\sigma_{u-f}$. The incompatible of the behavior of both experimental J-resistance curves using Rice's formula and CTOD-resistance curves for A533B and BS4360 steel by Gordon, et al., could be corrected using the optimal factor of revision in Rice\`s and the pertinent reference strength in J=$m_{j}$${\times}$$\sigma_{i}$${\times}$CTOD.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.4 s.142
• /
• pp.315-321
• /
• 2005

The effect of water depth on the wave making resistance performance is great where Froude number based on the water depth is close to one. The increase of wave making resistance due to the shallow water effect is evaluated by a numerical analysis in the present study. Three-dimensional Navier-Stokes and continuity equations are employed for the present study and the equations are discretized by finite difference method. The interface between water and air is determined by the level set method. In order to validate the numerical method, the change of resistance performance for Wigley hull according to the water depth is evaluated and the computed resistance coefficient is compared with measured one. The present numerical method is applied for the simulation of wave phenomena around a Ro-Pax hull form and the computed results are discussed in the resistance performance point of view.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.5
• /
• pp.1068-1072
• /
• 2011

Hydrogen Fuel Cell Vehicle(HFCV) is system that uses electrical energy of fuel cell stack to main power source, which is different system with other vehicles that use high-voltage, large-current. Isolation performance of this system which is connected with electrical fire and electrical shock is important point. Isolation resistance of electric installation is divided according to working voltage, it follows criterion more than $100{\Omega}$/VDC (or $500{\Omega}$/VAC) about system operation voltage in a hydrogen fuel cell vehicle. Although measurement of isolation resistance in a hydrogen fuel cell vehicle is two methods, it uses mainly measurement by megger. However, the present isolation resistance measurement system that is optimized to use in electrical facilities is unsuitable for isolation performance estimation of a hydrogen fuel cell vehicle because of limit of maximum short current and difference of measurement resolution. Therefore, this research developed the isolation resistance measurement system so that may be suitable in isolation performance estimation of a hydrogen fuel cell vehicle, verified isolation performance about known resistance by performance verification of laboratory level about developed system, and executed performance verification through comparing results of developed system by performance verification of vehicle level with ones of existing megger. Developed system is judged to aid estimation and upgrade of isolation performance in a hydrogen fuel cell vehicle hereafter.

• The korean journal of orthodontics
• /
• v.23 no.4 s.43
• /
• pp.619-631
• /
• 1993

Tooth movement by segment is one of the means which are frequently used in daily orthodontic practice. When we retract or intrude a tooth or teeth, we should recognize the center of resistance of the certain tooth or teeth. There have been many studies about the center of resistance of a single tooth, not so much was about the tooth-segment. At the present study the center of resistance of the maxillary anterior segment is experimentally investigated by using laser reflection technique and metal splints on the human dry skull. The variables of intrusive force magnitude are divided into two groups, 50g and 100g groups. The results were as follows ; 1. The center of resistance of the maxillary anterior segment composed of the central and lateral incisors was at the mesial portion of canine crown at the coronal level. 2. The center of resistance of the maxillary anterior segment composed of the central and lateral incisors and canines is between the canine and the 1st premolar crowns at the coronal level.

• Geomechanics and Engineering
• /
• v.15 no.3
• /
• pp.879-888
• /
• 2018

Probability-based design codes have been developed to sufficiently confirm the safety level of structures. One of the most acceptable probability-based approaches is Load Resistance Factor Design (LRFD), which measures the safety level of the structures in terms of the reliability index. The main contribution of this paper is to calibrate the load and resistance factors of the design code for tunnels. The load and resistance factors are calculated using the available statistical models and probability-based procedures. The major steps include selection of representative structures, consideration of the limit state functions, calculation of reliability for the selected structures, selection of the target reliability index and calculation of load factors and resistance factors. The load and resistance models are reviewed. Statistical models of resistance (load carrying capacity) are summarized for strength limit state in bending, shear and compression. The reliability indices are calculated for several segments of a selected circular tunnel designed according to the tunnel manual report (Tunnel Manual). The novelty of this paper is the selection of the target reliability. In doing so, the uniform spectrum of reliability indices is proposed based on the probability paper. The final recommendation is proposed based on the closeness to the target reliability index.

• Food Science of Animal Resources
• /
• v.36 no.3
• /
• pp.352-358
• /
• 2016

The aim of this study was to determine the prevalence of enterococci in cheese samples and to characterize their antimicrobial resistance profiles as well as the associated resistance genes. A total of 139 enterococci were isolated from 99 cheese samples, the isolates were identified as E. faecalis (61.2%), E. faecium (15.1%), E. gallinarum (12.9%), E. durans (5.0%), E. casseliflavis (2.9%) and E. avium (2.9%). The most frequent antimicrobial resistance observed in enterococci isolates was to lincomycin (88.5%), followed by kanamycin (84.2%), gentamycin (low level, 51.1%), rifampin (46.8%) and tetracycline (33.8%). Among the isolates, the frequencies of high level gentamycin and streptomycin resistant enterococci strains were 2.2% and 5.8%, respectively. Apart from the mentioned antibiotics, low levels of resistance to ciprofloxacin, erythromycin and chloramphenicol were found. Moreover no resistance was observed against penicillin and ampicillin. The antimicrobial resistance genes including tetM, tetL, ermB, cat, aph(3’)-IIIa, ant(6)-Ia and aac(6’)-Ieaph(2”)-Ia were found in enterococci from Turkish cheese samples. In the current study, we provided data for antibiotic resistance and the occurrence of resistance genes among enterococci. Regulatory and quality control programs for milk and other dairy products from farms to retail outlets has to be established and strengthened to monitor trends in antimicrobial resistance among emerging food borne pathogens in Turkey.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.6
• /
• pp.873-880
• /
• 2018

Objective: The objective of this experiment was to compare the effects of adding 130 mg/kg Cu from either copper sulfate (CS) or tribasic copper chloride (TBCC) on growth performance, mineral deposition in tissues, and the excretion in feces of pigs as well as changes in the mineral contents in tissues and feces when the supplemental Cu level was decreased from 130 mg/kg to 10 mg/kg. Methods: A total of 72 pigs ($32.6{\pm}1.2kg$) were randomly assigned to a CS diet or a TBCC diet with 6 pens per treatment. The trial lasted 102 d and included 3 phases (phase 1, 1 to 30 d; phase 2, 31 to 81 d; and phase 3, 82 to 102 d). The supplemental levels of Cu in the 2 treatments were 130 mg/kg in phase 1 and 2 and 10 mg/kg in phase 3. Results: The results showed that pigs fed the CS diet tended to have higher average daily gain than pigs fed the TBCC diet during d 1 to 81 (p<0.10). Compared with CS, TBCC increased the activities of aspartate transaminase (AST), ceruloplasmin, and superoxide dismutase in serum on d 30 (p<0.05). The TBCC decreased the Cu level in the liver on d 81 (p<0.05) and increased the Mn level in the liver on d 102 (p<0.05). The concentration of Cu in feces sharply decreased when the supplemental Cu level in diet changed from 130 mg/kg to 10 mg/kg in both diets (p<0.05). Conclusion: The result suggested that TBCC and CS had no significant difference on growth performance but TBCC had higher activities of AST and antioxidant enzymes and lower liver Cu than CS when pigs fed diets with 130 mg Cu /kg diet.