• International Journal of Highway Engineering
• /
• v.17 no.4
• /
• pp.53-61
• /
• 2015

PURPOSES : The objective of this study is to evaluate the SDAR (solvent deasphaltene residue), which is obtained from the solvent deasphalting (SDA) process, as a pavement material. METHODS : The physical properties of the SDAR were evaluated based on its chemical composition, and asphalt mixtures with the SDAR were fabricated and used for the evaluation of mechanical properties. Firstly, the chemical composition of SARA (saturate, aromatic, resin and asphaltene) was analyzed using the TLC-FID (thin-layer chromatography-flame ionization detector). Moreover, the basic material properties of the asphalt binder with the SDAR were evaluated by the penetration test, softening point test, ductility test, and PG (performance grade) grade test. The rheological properties of the asphalt binder with the SDAR were evaluated by the dynamic shear modulus ($G^*$) obtained using the time-temperature superposition (TTS) principle. Secondly, the mechanical properties of the asphalt mixtures with the SDAR were evaluated. The compactibility was evaluated using the gyratory compacter. Moreover, the tensile strength ratio (TSR) was used for evaluating the moisture susceptibility of the asphalt mixtures (i.e., susceptibility to pothole damage). The dynamic modulus $E^*$, which is a fundamental property of the asphalt mixture, obtained at different temperatures and loading cycles, was used to evaluate the mechanical properties of the asphalt mixtures. RESULTS AND CONCLUSION : The SDAR shows stiffer and more brittle behavior than the conventional asphalt binder. As the application of the SDAR directly in the field may cause early failures, such as cracks on pavements, it should be applied with modifiers that can favorably modify the brittleness property of the SDAR. Therefore, if appropriate additives are applied on the SDAR, it can be used as a pavement material because of its low cost and strong resistance to rutting.

• Journal of the Korean Society of Safety
• /
• v.32 no.3
• /
• pp.1-7
• /
• 2017

Particle reinforced composites are materials that have enhanced physical properties by adding particle reinforcements to polymer materials and have been applied to a wide range of fields such as the aerospace, bio-technology and automative industry. In this study, particle reinforced composites were prepared by mixing $SiC/Al_2O_3$ to the vinyl ester as the thermoset resin. The purpose of this study is to evaluate mechanical properties and fracture behavior by the tensile test and single edge notch specimen according to the addition ratio of reinforcement. Addition of 1 and 2 wt% of the particle reinforcement to the vinyl-ester resin was effective for the strength improvement. However, when it was more than 3 wt%, its strength was decreased. Also the highest elastic modulus obtained as 3.19 GPa was found at the 2 wt% addition of reinforcement. Futhermore the fracture toughness was evaluated by the energy release rate and the maximum critical energy release rate was obtained when 1 wt% reinforcement. The results show that the limit of adding of $SiC/Al_2O_3$ for improvement of the mechanical and fracture performance is 2 wt% reinforcement particles.

• Resources Recycling
• /
• v.8 no.3
• /
• pp.3-8
• /
• 1999

An air-washer was developed in order to remove the soil on the films collected from agricultural use, The washed films were subjected to TGA analysis to measure the residual soil content and DSC analysis to evaluate composition as well as compositional ratro, Mechanical properties of washed films were measured via tensile test ,md the properties of washed films were compared with those of neat resin blend. Major component of air washed films was polyethylene, and compositional ratio was 10:6:3:1 (HDPE:LLDPE:LDPE:EVA). 30 min air-washed films showed 2.1 % of residual soil content, while the water washed films had 1.5%. Tensile properties of washed (air and water) films were almost same as those of neat resin mixture.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.775-785
• /
• 2006

This study focused on the development of surface deformations of GFRP rebars with a better bond characteristic for reinforcing concrete, and simultaneously, of GFRP rebars with more simple and economic production process. This research paper describes a development and bond performance of GFRP rebar with molded deformations, which is composed of polymer resin and milled glass fiber. To determine proper mix ration of milled fibers, material test of hardened epoxy and pullout tests of GFRP rebar with various mix ratio were conducted. The test results indicate that the new strategy of using a mixture of epoxy resin and milled fiber could be successfully applied to a surface structure of GFRP rebar to enhance bond with concrete. The bearing resistance of the ribs was further enhanced by the milled fibers at mechanical and environmental loading state.

• Journal of the Korean Chemical Society
• /
• v.18 no.5
• /
• pp.381-388
• /
• 1974

When mixture of p-phenylenediamine (PPD) and m-aminophenol (MAP) were reacted with formaldehyde (F) varying their amounts under $N_2$ stream at the temperature of -5∼0$^{\circ}$, addition condensation reaction occurred and brown colored resins(in some cases orange colored) were formed immediately. All resins thus formed were insoluble in most ordinary organic solvents and did not melt up to 300$^{\circ}$. When the resins were treated with dilute(7 %) aqueous sodium hydroxide solution, the adsorptivity of methylene blue on them showed marked improvement reaching as much as 80 mg of methylene blue on 1 g of the resin. On the other hand, in the case of bromophenol blue, its amount of adsorption appeared 250 mg per 1 g of the resin. The TGA under $N_2$ atmosphere indicated that the resin formed in molar ratio of 1 : 3 : 8 (PPD : MAP : F) showed the best heat-resistant property among others. About 40 % weight loss was observed for this resin at 900$^{\circ}$ with heating rate of 2$^{\circ}$ per minute.

• Applied Chemistry for Engineering
• /
• v.20 no.3
• /
• pp.339-345
• /
• 2009

The graft copolymerization of acrylonitrile-EPDM-styrene (AES) was investigated under various reaction conditions such as the concentration of initiator, the content of diene and viscosity of EPDM, and the concentration of solvents. The conversion increased but the molecular weight and the rubber particle size decreased with the concentration of initiator. The graft ratio(GR) increased at low concentrations of the initiator but, after the maximum value, it gradually decreased with the concentration of initiator. Toluene as a single solvent gave the highest conversion and the mixture of ethyl benzene and toluene was better than toluene. The rubber particle size increased with the viscosity of EPDM and the graft ratio and the number of rubber particles with occluded SANs increased with the content of diene.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.99-99
• /
• 2010

Polymer nanocomposite has been attracting much attention as a new insulation material, since homogeneous dispersion of nm-sized inorganic fillers can improve various properties significantly. In this paper, various kinds of epoxy based nanocomposites were made and AC breakdown strength of Nano-TiO2 and micro-silica filler mixture of epoxy based composites were studied by sphere to sphere electrode. Moreover, nano- and micro-filler combinations were adopted as an approach toward practical application of nanocomposite insulation materials. Nano-TiO2 particle size is about 10nm and composites ratio was resin (100) : hardener (82) : accelerator (1.5). AC breakdown test was performed at room temperature (25 [$^{\circ}C$], 80 [$^{\circ}C$] and 100 [$^{\circ}C$] in the vicinity of Tg (90[$^{\circ}C$]). And thermal conductivity were measured by ASTM-D5470.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.2
• /
• pp.74-84
• /
• 1990

The machine tool structures for ultra-precision machining muxt be manufactured with materials which have high static and dynamic stiffness, high damping, a long term dimensional and thermal stability. This study aims at the development of new composite material Epoxy-Granite which exhibits the satisfactory characteristics as a material of ultra-precision mchine tool bed. The Epoxy-Granite testpieces that use epoxy resins as a binder and granite particles as a aggregate have been manufactured so as to examine the material properties about mechanical, thermal and damping characteristics. Experiments were carried out to obtain the proper manufacturing conditions of Expoxy-Granite specimens by varying the several testing conditions such as types of epoxy resins, particle sizes of granite and mixture ratio of epoxy resin and aggregate. Also, when Epoxy-Granite was compared with cast iron, GRANITAN which was imported from CMS of U.K. and granite materials, it has exhibited the superior or almost the same mechanical and damping properties and thermal conductivity, except for the thermal expansion.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.79-87
• /
• 2008

Many researchers have studied on rooftop greening that can be installed in abandoned spaces on a building roof. The most important issue in rooftop greening is the soil weight problem. The light greening materials are needed to solve this problem. Therefore, many alternative materials against the soil were investigated for rooftop greening. In this study, the waste wood chips and the waste paper slurry were evaluated as the lightweight vegetation foundation for rooftop greening. It also has a meaning for recycling of waste materials. The mixture ratio of waste wood chips to waste paper slurry for the board (the foundation of greening) was 60 to 40. The wet strength resin and the sizing agent were additionally added with different amount. After the forming of the board, physical and chemical properties were tested with the variation of wet strength resin and sizing agent. As the result of the test, the board with 15% of wet strength resin in the wet condition showed the highest strength. Futhermore, the moisture evaporation loss from the board surface with sizing agent was much lower than that from the board without sizing agent. Therefore, it was clear that the sizing agent was effective for water retention. The change of thickness in the wet condition was less than 1 mm, and it showed that the board is the predominant material on the dimensional stability. The average pH value of the board was ranged from 7.6 to 8.25.

• Restorative Dentistry and Endodontics
• /
• v.37 no.2
• /
• pp.96-103
• /
• 2012

Objectives: This study evaluated the effect of camphorquinone (CQ)-amine ratio on the C=C double bond conversion of resins with binary and ternary photoinitiation systems. Materials and Methods: Two monomer mixtures (37.5 Bis-GMA/37.5 Bis- EMA/25 TEGDMA) with binary systems (CQ/DMAEMA in weight ratio, group A [0.5/1.0] and B [1.0/0.5]) and four mixtures with ternary system (CQ/OPPI/DMAEMA, group C [0.1/1.0/0.1], D [0.1/1.0/ 0.2], E [0.2/1.0/0.1] and F [0.2/1.0/0.2]) were tested: 1 : 2 or 2 : 1 CQ-amine ratio in binary system, while 1 : 1 ratio was added in ternary system. The monomer mixture was cured for 5, 20, 40, and 300 sec with a Demetron 400 curing unit (Demetron). After each exposure time, degree of conversion (DC) was estimated using Fourier transform infrared (FTIR) spectrophotometer (Nicolet 520, Nicolet Instrument Corp.). The results were analyzed by ANOVA followed by Scheffe test, with p = 0.05 as the level of significance. Results: DC (%) was expressed in the order of curing time (5, 20, 40, and 300 sec). Group A ($14.63{\pm}10.42$, $25.23{\pm}6.32$, $51.62{\pm}2.69$, $68.52{\pm}2.77$); Group B ($4.04{\pm}6.23$, $16.56{\pm}3.38$, $37.95{\pm}2.79$, $64.48{\pm}1.21$); Group C ($16.87{\pm}5.72$, $55.47{\pm}2.75$, $60.83{\pm}2.07$, $68.32{\pm}3.31$); Group D ($23.77{\pm}1.64$, $61.05{\pm}1.82$, $65.13{\pm}2.09$, $71.87{\pm}1.17$); Group E ($28.66{\pm}2.92$, $56.68{\pm}1.33$, $60.66{\pm}1.17$, $68.78{\pm}1.30$); Group F ($39.74{\pm}6.31$, $61.07{\pm}2.58$, $64.22{\pm}2.29$, $69.94{\pm}2.15$). Conclusion: All the monomers with ternary photoinitiation system showed higher DC than the ones with binary system, until 40 sec. Concerning about the effect of CQ-amine ratio on the DC, group A converted into polymer more than group B in binary system. However, there was no significant difference among groups with ternary system, except group C when cured for 5 sec only.