• Geomechanics and Engineering
• /
• 제9권3호
• /
• pp.373-395
• /
• 2015

Comprehensive results from cyclic plate loading at a diameter of 300 mm supported by layers of geocell are presented. The plate load tests were performed in a test pit measuring $2000{\times}2000mm$ in plane and 700 mm in depth. To simulate half and full traffic loadings, fifteen loading and unloading cycles were applied to the loading plate with amplitudes of 400 and 800 kPa. The optimum embedded depth of the first layer of geocell beneath the loading plate and the optimum vertical spacing of geocell layers, based on plate settlement, are both approximately 0.2 times loading plate diameter. The results show that installation of the geocell layers in the foundation bed, increase the resilient behavior in addition to reduction of accumulated plastic and total settlement of pavement system. Efficiency of geocell reinforcement was decreased by increasing the number of the geocell layers for all applied stress levels and number of cycles of applied loading. The results of the testing reveal the ability of the multiple layers of geocell reinforcement to 'shakedown' to a fully resilient behavior after a period of plastic settlement except when there is little or no reinforcement and the applied cyclic pressure are large. When shakedown response is observed, then both the accumulated plastic settlement prior to a steady-state response being obtained and the resilient settlements thereafter are reduced. The use of four layers of geocell respectively decreases the total and residual plastic settlements about 53% and 63% and increases the resilient settlement 145% compared with the unreinforced case. The inclusion of the geocell layers also reduces the vertical stress transferred down through the pavement by distributing the load over a wider area. For example, at the end of the load cycle of the applied pressure of 800 kPa, the transferred pressure at the depth of 510 mm is reduced about 21.4%, 43.9%, 56.1% for the reinforced bases with one, two, and three layers of geocell, respectively, compared to the stress in the unreinforced bed.

• 대한치과보철학회지
• /
• 제35권3호
• /
• pp.577-608
• /
• 1997

The purpose of this study is to evaluate the stress distribution in the bone around dental implants supporting mandibular overdenture according to the number of implant and the type of attachment. Two or four implants were placed in an edentulous mandibular model and three dimensional photoelastic stress analysis was carried out to measure the fringe order around the implant supporting structure and also to calculate principal stress components at cervical area of each implant. The attachments tested were rigid and resilient type of Dolder bar, Round bar, Hader bar and Dal-Ro attchment. The results were as follows ; 1. In 2-implant supported overdenture using Round bar, Hader bar, and Dal-Ro attachment, compressive stress pattern was observed on the supporting structure of implant on loaded side, while tensile stress pattern in unloaded side. 2. In 2-implant supported overdenture using Dolder bar, the rigid Dolder bar shared the occlusal loads between 2 implants in a more favorable manner than was exhibited by the resilient type, while the resilient type placed a more stress on the distocervical area of the implant on the loaded side. But compressive stress pattern was observed in both the loaded and unloaded sides in either case. 3. In 2-implant supported overdenture, rigid and resilient type of Dolder bar exhibited more cross arch involvement than the Round bar, Hader bar, or Dal-Ro attachment. 4. In 4-implant supported overdenture using resilient Dolder bar and Hader bar, stress turned out to be distributed evenly among the implants between loaded and unloaded side, but thor was no reduction in the magnitude of the stress in the surrounding structure of implant contratry to 2-implant supported overdenture. 5. The stress pattern at cervical area of implant was different with the number of implant or the type of attachment but the overload, harmful to surrounding structure of implant, was not observed.

• 한국지반환경공학회 논문집
• /
• 제12권12호
• /
• pp.63-70
• /
• 2011

EPS지오폼은 다양한 강도, 밀도, 그리고 크기로 생산되는 일종의 화학합성물이다. EPS지오폼에 관한 근래의 발전으로 인해서, 그것의 사용은 급격하게 늘어나고있다. 이것은 초경량 재료로서 단위중량이 약 $0.16{\sim}0.47kN/m^3$ 인데, 이것은 채움재의 용도로 가장 대표적인 흙의 단위중량 $6.3{\sim}15.7kN/m^3$와 동일한 내구성을 가진다. 이런 장점에도 불구하고, EPS지오폼에 대한 회복탄성계수 표준측정방법은 보고된 바가 없는 실정이다. 본 연구의 주된 목적은 연성포장의 노반에 적용될 때의 EPS회복탄성계수의 적합성을 연구하는 것이다. 적합성연구는 삼축압축시험의 결과를 토대로 이루어졌으며, 연성포장의 노반재료로써 EPS는 실험결과의 분석과 근본적인 회복탄성의 특성을 비교분석하여 그것의 적합성을 확인해 보았다.

• 한국음향학회지
• /
• 제42권2호
• /
• pp.161-167
• /
• 2023

최근 바닥충격음 사후 성능검사 제도의 시행에 따라 공동주택 바닥 슬래브 상부에 설치되는 바닥 마감재에 대한 바닥충격음 성능 개선의 요구사항은 증가하고 있다. 하지만 현재의 KS F ISO 717-2 및 KS F 2863에서의 바닥 마감재 성능 평가방법은 완충층이 설치되지 않은 조건에서 저감량을 측정하는 것으로 되어 있다. 준공 전 성능측정 의무화로 인해 본인이 거주하는 공동주택 바닥충격음 성능의 확인이 가능한 상황에서 입주민이 거주하는 공동주택의 특성을 반영하는 온돌층이 설치된 구조에서의 성능평가는 마감재의 바닥충격음 성능에서 더 필요한 부분일 것이다. 따라서 본 논문에서는 바닥슬래브 상부 마감구조의 저감량 평가를 위해서 완충층 조건을 포함한 저감성능 평가를 제안하고, 완충층 성능에 따른 저감량의 차이를 확인할 수 있도록 마감재가 설치되지 않은 상태의 바닥충격음 성능을 동시에 표시하는 것을 제안한다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2004년도 학술.기술논문발표회
• /
• pp.5-10
• /
• 2004

Apartment Buildings have particularity to cluster together, especially, floor is close to resident, it is subject to dissatisfaction about impact noise between up and down floors. However, we require standard for counterplan to reduce the impact noise of floor. In point of fact, it difficult to objective evaluate for performance sound insulation that not physical sound volume but orignal form, means and effect of sound caused to complex noise in apartment house. Unique type of dwelling and structure pattern cause to noise of floor impact which is established by law for standard regulation. It is object to analysis and compare the result of performance sound insulation of upper floor impact and sample construct the subject resilient material of sound insulator

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3237-3250
• /
• 2011

As the growing concern about environment and earthquake for the concrete structure, many seismic rehabilitation and retrofitting methods have recently been studied but they are not coping enough with the changes of structure, specificly various problems have been found in seismic rehabilitation method - both in exposure or non exposure - when they are implemented to the underground structure, utility conduit, water supply facilities, underground wall, parking lot, road pavement, and elevated structure etc. This study is about the seismic rehabilitation method using environmentally friendly functional inorganic mortar and resilient material, and it is effectively retrofitted seismic performance as it reinforces not only physical strength, but also flexural and bond strength from the resilient material, and it has been analyzed and evaluated when the environmentally friendly functional inorganic mortar and the resilient material are applied so as to countermeasure the effect of earthquake and viable problems and approved for possibility of various applications and wide use.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.356-360
• /
• 2006

Recently, for the purpose of improving the isolation performance of impact noise, many resilient materials have been installed in a residential building. As one of the reduction method for improving the performance of light-weight impact noise, this study is focused on the load condition of floating layer over resilient material. We studied the correlation between the mass or load of the floating layer and the reduction of light-weight impact noise by experiments in reverberation chamber for testing the impact noise. The results show that the reduction of impact noise is improved by increasing the mass per unit area of floating layer until about $140kg/m^2$. But the reduction is not obvious by adding extra mass on the floating layer.

• 한국농공학회논문집
• /
• 제52권2호
• /
• pp.51-57
• /
• 2010

Many models have been used to represent the effects of confining stress, bulk stress, and shear stress on the value of the resilient modulus (Mr). This study was conducted to estimate Mr of the recycled materials such as recycled concrete aggregate (RCA) and recycled asphalt pavement (RAP) through the repeated load cyclic test. Also, two models were applied to estimation of Mr for comparing between measured Mr values and predicted Mr values. The first model (A-model) can provide a quick and easy estimation of the Mr based on the bulk stress, while the second model (N-model) includes not only the bulk stress but also the shear stress. Statistical analysis indicated that all results using the both of models are significant at a 95 % confidence level. Therefore, the both of models could be used as an effective prediction model of Mr for RCA and RAP. Especially, the Model 2 including the parameters of the bulk stress and the shear stress could give more reliable estimation at the high range of Mr values.

• 한국농공학회논문집
• /
• 제52권2호
• /
• pp.19-25
• /
• 2010

This study was conducted to determine the resilient modulus (Mr) and the unconfined compressive strength (UCS) of two recycled roadway materials such as recycled pavement material (RPM) and road surface gravel (RSG) with or without cement kiln dust (CKD). The recycled materials were blended with two CKD contents (5, 10 %) and 28 day curing time. Mr and UCS tests were also conducted after 10cycles of freezing and thawing to asses the impact of freeze-thaw cycling. Mr was determined conducting by the laboratory test method described by NCHRP 1-28A. Stabilized RPM and RSG had a modulus and a strength higher than unstabilized RPM and RSG. Mr and UCS of RPM and RSG mixed with CKD increased with increasing CKD content. The results indicated that the addition of CKD could be improved the strength and the stiffness of RPM and RSG. Therefore, RPM, RSG and CKD could be used as an effective materials in the reconstruction of roads.

• 연구논문집
• /
• 통권29호
• /
• pp.83-90
• /
• 1999

In naval ships, pump machineries are the major sources of airborne and structure-borne noise. Noise is critical issue in ships not only it causes annoyance to crews, but also it can increase the underwater radiated noise, which is crucial in anti-submarine warfare. In present study, it is discussed the reduction of structure-borne noise of pump machineries by showing several examples. The most typical and effective solution is to use double resilient mount system. However, in cases where double resilient system cannot be applied due to space and weight increase, rubber pad can be used to reduce the structure-borne noise. In principle, the concept of structure-borne noise reduction is the same as that of vibration isolation.