• 환경위생공학
• /
• 제13권1호
• /
• pp.57-68
• /
• 1998

This study was surveyed to examine the removable ability of residual aluminum with the coagulants(LAS, PAC) and the auxiliary coagulants(Loess, R-calmont) on raw water. The leaching test of the auxiliary coagulant showed that the loess contained a lot of Al, Fe and Mn. On the reverse, the R-calmont was a little. Most of the loess were composed of $SiO_{2}$ 53.25%, $Al_{2}O_{3}$ 29.28%, $Fe_{2}O_{3}$ 10.73% and Si/Al ratio was 3.08. In using both LAS vs. loess and PAC vs. loess as the coagulated material, the removal of residual aluminum was the highest as 96.3%, 96.6% respectively, and that of the residual turbidity was 95.0% when PAC vs. R-calmont was dosed 0.2mg/L. Also, loess showed better than R-calmont in the removable efficiency of aluminum and turbidity. When the setting time of auxiliary coagulant was input ar the same time with coagulant, the removal aluminum was the highest as 93.3% to 96.6%.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.77-82
• /
• 1999

Resistance spot welding process is completed in very short time and there are many factors affecting on the generation of heat. It is difficult to control these experimental factors and monitor distribution of the temperature and stresses in the experimental analysis case. and too much time and expense are required for the experimental trials to fine proper welding condition. So numerical analyses have been attempted steadily, but most numerical analyses on the resistance spot welding are mainly focused on thermal behavior. Therefore, in this paper, the numerical analysis of mechanical behavior as well as heat conduction is carried out for the spot welding process. For this numerical analysis, axial symmetric computer program for the spot welding analysis by F.E.M. has been developed considering heat conduction and thermal elastic-plastic theory. Material properties depending on temperature such as density, heat conductivity, heat expansion coefficient, specific heat, yield stress, elastic modulus, and specific resistance are considered. Using the results of temperature distribution obtained from heat conduction analysis, the thermal elastic-plastic analysis is carried out to clarify mechanical behavior of spot welded specimen. In order to evaluate the effect of residual stresses, numerical analyses are carried out under tension-shear load in two cases respectively; one with residual stress, the other without residual stresses.

• Asian Spine Journal
• /
• 제12권6호
• /
• pp.1069-1077
• /
• 2018

Study Design: A case study. Purpose: To assess the chronological changes of the disease-related kyphosis after chemotherapy alone, secondly to clarify the role of growth cartilage in the healed lesion on kyphosis change, and to define the accurate prediction time in assessing residual kyphosis. Overview of Literature: None of the previous papers up to now dealt with the residual kyphosis, stability and remodeling processes of the affected segments. Methods: One hundred and one spinal tuberculosis children with various stages of disease processes, age 2 to 15 years, were the subject materials, between 1971 to 2010. They were treated with two different chemotherapy formula: before 1975, 18 months of triple chemotherapy (isoniazid [INH], para-aminosalicylic acid, streptomycin); and since 1976, 12 months triple chemotherapy (INH, rifampicin, ethambutol, or pyrazinamide). The first assessment at post-chemotherapy one year and at the final discharge time from the follow-up (36 months at minimum and 20 years at maximum) were analyzed by utilizing the images effect of the remaining growth plate cartilage on chronological changes of kyphosis after initiation of chemotherapy. Results: Complete disc destruction at the initial examination were observed in two (5.0%) out of 40 cervical spine, eight (26.7%) out of 30 dorsal spine, and six (19.4%) out of 31 lumbosacral spine. In all those cases residual kyphosis developed inevitably. In the remainders the discs were partially preserved or remained intact. Among 101 children kyphosis was maintained without change in 20 (19.8%), while kyphosis decreased in 14 children (13.7%), and increased in 67 children (66.3%) with non-recoverably damaged growth plate, respectively. Conclusions: It could tentatively be possible to predict the deformity progress or non-progress and spontaneous correction at the time of initial treatment, but it predictive accuracy was low. Therefore, assessment of the trend of kyphotic change is recommended at the end of chemotherapy. In children with progressive curve change, the deformity assessment should be continued till the maturity.

• 한국생산제조학회지
• /
• 제18권3호
• /
• pp.255-260
• /
• 2009

This paper presents an experimental result of virtual mode input shaping for positioning stage. Input shaping is liable to increase the rise time of the system, which often degrades the performance of system. The virtual mode input, shaping is an input shaper design method to improve this problem. Experiments are performed with a precise positioning stage with a flexible beam of which natural frequency is adjustable. The experimental results show that the virtual-mode shaper is useful to reduce the rise time as well as the residual vibration of precise positioning stages.

• The Journal of the Acoustical Society of Korea
• /
• 제27권1E호
• /
• pp.1-10
• /
• 2008

A noise suppression algorithm is proposed for nonstationary noisy environments. The proposed algorithm is different from the conventional approaches such as the spectral subtraction algorithm and the minimum statistics noise estimation algorithm in that it classifies speech and noise signals in time-frequency bins. It calculates the ratio of the variance of the noisy power spectrum in time-frequency bins to its normalized time-frequency average. If the ratio is greater than an adaptive threshold, speech is considered to be present. Our adaptive algorithm tracks the threshold and controls the trade-off between residual noise and distortion. The estimated clean speech power spectrum is obtained by a modified gain function and the updated noisy power spectrum of the time-frequency bin. This new algorithm has the advantages of simplicity and light computational load for estimating the noise. This algorithm reduces the residual noise significantly, and is superior to the conventional methods.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.119-120
• /
• 2011

Recently, the effects of high temperature and fiber content on the residual mechnical properties of high-strength concrete were experimentally investigated. In this paper, residual mechanical properties of concrete with water to cement (w/c) ratios of 55%, 42% and 32% exposed to high temperature are compared with those obtained in fiber reinforced concretes of similar characteristics with the ranging of 0,05% to 0,20% polypropylene (PP) fibers by volume of concrete, and considered factors include pre-load levels (20% and 40% of the maximum load at room temperature). Outbreak time and water contents were tested and were determined the compressive strength. In the result, it is showed that to prevent the explosive spalling of 50MPa grade concretes exposed to high temperature need more than 0.05Vol.% PP fibers. Also, the cross-sectional area of PP fiber can influence on the residual mechanical properties and the spalling tendency of fiber reinforced concrete exposed to high temperature. Especially, the external loading increases not only the residual mechanical properties of concrete but also the risk of spalling and the brittle tendency.

• 한국동물위생학회지
• /
• 제21권4호
• /
• pp.379-383
• /
• 1998

This survey was carried out to determine 5 residual sulfonamides(sulfamerazine : SMR, sulfamethazine : SMT, sulfamonomethoxine : SMM:, sulfadimethoxine : SDM, sulfaquinoxaline : SQX) in muscle of mouse. For this investigation, pertaining detection wavelength, residual levels and residual times in muscle of mouse were summarized as follows ; 1. Pertaining detection wavelength of 5 residual sulfonamides(SMR, SMT, SMM, SDM, SQX) was 270nm by HPLC/UV detection. 2. After 1 day put a stop to sulfonamides administration, residual levels was 1∼l.5ppm, but were not detected at day 7 3. Withdrawal time of 5 sulfonamides were about 7 days suspectly.

• 한국재료학회지
• /
• 제31권12호
• /
• pp.697-703
• /
• 2021

Aluminum nitride having a dense hexagonal structure is used as a high-temperature material because of its excellent heat resistance and high mechanical strength; its excellent piezoelectric properties are also attracting attention. The structure and residual stress of AlN thin films formed on glass substrate using TFT sputtering system are examined by XRD. The deposition conditions are nitrogen gas pressures of 1 × 10^-2, 6 × 10^-3, and 3 × 10^-3, substrate temperature of 523 K, and sputtering time of 120 min. The structure of the AlN thin film is columnar, having a c-axis, i.e., a <00·1> orientation, which is the normal direction of the glass substrate. An X-ray stress measurement method for crystalline thin films with orientation properties such as columnar structure is proposed and applied to the residual stress measurement of AlN thin films with orientation <00·1>. Strength of diffraction lines other than 00·2 diffraction is very weak. As a result of stress measurement using AlN powder sample as a comparative standard sample, tensile residual stress is obtained when the nitrogen gas pressure is low, but the gas pressure increases as the residual stress is shifts toward compression. At low gas pressure, the unit cell expands due to the incorporation of excess nitrogen atoms.

• Current Optics and Photonics
• /
• 제7권4호
• /
• pp.408-418
• /
• 2023

Due to the technological limitations of infrared thermography, infrared focal plane array (IFPA) imaging exhibits stripe non-uniformity, which is typically fixed pattern noise that changes over time and temperature on top of existing non-uniformities. This paper proposes a stripe non-uniformity correction algorithm based on scene-adaptive nonlinear filtering. The algorithm first uses a nonlinear filter to remove single-column non-uniformities and calculates the actual residual with respect to the original image. Then, the current residual is obtained by using the predicted residual from the previous frame and the actual residual. Finally, we adaptively calculate the gain and bias coefficients according to global motion parameters to reduce artifacts. Experimental results show that the proposed algorithm protects image edges to a certain extent, converges fast, has high quality, and effectively removes column stripes and non-uniform random noise compared to other adaptive correction algorithms.

• 한국정보통신학회논문지
• /
• 제11권10호
• /
• pp.1845-1851
• /
• 2007

배경 잡음과 실내 잔향음은 음성 인식 시스템 성능 저하의 주요 이유이다. 많은 알고리즘이 음성의 잔향음 제거를 위해 개발되었다. 이 논문에서는 실내 환경에서 수정된 선형 예측 잔여(Linear Prediction Residual)를 이용하여 음질 개선을 위한 잔향음 제거 방법을 제안한다. 제안된 잔향음 제거 방법은 음성에서 성문 경계의 순간에 발생한 성도(聲道)시스템의 중요한 여기에 기반한다. 본 논문에서 제안한 방법은 3개의 센서로부터 수집한 반향신호로 각 센서에서의 시간지연 정보를 사용한다. 새로운 선형 예측 잔여신호는 선형 예측 잔여의 가중치와 힐버트 변환으로 얻은, 개선된 선형 예측 잔여 조합을 사용한다. 코히런트하게 더해진 힐버트 포락선의 특징은 잡음과 반사로 인한 큰 진폭 피크를 가지는 것이다. 깨끗한 음성의 잔여는 개선된 음성을 얻는 시변전극 필터를 일으키는데 사용된다. 본 논문에서는 반향 환경에서 성능 분석을 위해 제안된 알고리즘의 시뮬레이션을 수행하였다. 제안된 알고리즘은 실내 잔향환경에서 기존의 알고리즘에 비해 반사된 음성의 품질 향상의 결과를 보였다.