• BioChip Journal
• /
• 제12권4호
• /
• pp.332-339
• /
• 2018

The future neuro-prosthetic devices would be required spikes data monitoring through sub-nanoscale transistors that enables to neuroscientists and clinicals for scalable, wireless and implantable applications. This research investigates the spikes monitoring through integrated CNT front-end amplifier for neuro-prosthetic diagnosis. The proposed carbon nanotube-based architecture consists of front-end amplifier (FEA), integrate fire neuron and pseudo resistor technique that observed high electrical performance through neural activity. A pseudo resistor technique ensures large input impedance for integrated FEA by compensating the input leakage current. While carbon nanotube based FEA provides low-voltage operation with directly impacts on the power consumption and also give detector size that demonstrates fidelity of the neural signals. The observed neural activity shows amplitude of spiking in terms of action potential up to $80{\mu}V$ while local field potentials up to 40 mV by using proposed architecture. This fully integrated architecture is implemented in Analog cadence virtuoso using design kit of CNT process. The fabricated chip consumes less power consumption of $2{\mu}W$ under the supply voltage of 0.7 V. The experimental and simulated results of the integrated FEA achieves $60G{\Omega}$ of input impedance and input referred noise of $8.5nv/{\sqrt{Hz}}$ over the wide bandwidth. Moreover, measured gain of the amplifier achieves 75 dB midband from range of 1 KHz to 35 KHz. The proposed research provides refreshing neural recording data through nanotube integrated circuit and which could be beneficial for the next generation neuroscientists.

• 복식문화연구
• /
• 제12권3호
• /
• pp.392-406
• /
• 2004

The purpose of this study is to recognize of the size conditions of ready to wear skirts and analyze the patterns of them so that some educational patterns can be complemented. For this purpose, the investigation of the size conditions was focused on the body sizes and products sizes of the care labels. The patterns of them produced through CAD have been classified into 24 items for the effective and practical analysis. Thus, 9 brands were selected and the basic skirts marketed in 2002 spring were analyzed. The results were as follows. 1. Designs of the backs of the basic skirts produced by 9 brands have the similar designs with two darts. Regarding the designs of the front, 6 brands of them have the designs with no darts, 3 of them have the one with two darts. Designs of waists are composed of low waists and round belts. 2. Regarding the waist circumference as the basic composing elements of skirts, 55.6% of the patterns have the composition of the styles with larger front than the back but 33.3% of them have the same front as back. As to the hips, 77.8% of them have the composition of the patterns with larger back than the front. As for the comparison of waist lines, 55.6% of them have lower front lines than the back lines. 3. Regarding darts placement, it was moved to the side lines from the middle of 1/2 of waist lines, dart intake was 1.8-2.4㎝, the length of the front darts was 7.8-9.5㎝, and the length of the back darts 8.4-11.1㎝ 4. The results of wearing-tests by the sensory evaluation, it showed that almost all the items of the results were satisfactory.

• 한국의류산업학회지
• /
• 제4권2호
• /
• pp.145-155
• /
• 2002

In order to investigate how upper limb motion gives influence on clothing, this study measured tests by following standards: Front Vertical motion, Side-Vertical motion, and Horizontal motion. For this study, the procedures in the order of alphabet are applied. A. Eeach of testee's pattern was copied by the motion with a method of tight fitting technique. B. Analyzing each of the size-change on measuring item. C. Studying the moving aspects at each datum points. The results shows that the biggest change can be found in the following items. 1) In vertical motion of F4 (the length to shoulder point from A-point) 2) In horizontal motion of F5 (the length to front-width point from A-point), the check-result gained by checking the notice between motions shows that the most noticeable items are F4 (the length to shoulder point from A-point), F5 (the length to front-width point from A-point), F6 (the length to armpit point from A-point), B7 (the length to side-waist point from B-point). In result of the study of datum point's movement by motion, the items which were measured with the longest on straight-distance in vertical motion are the front and rear-shoulder, and the rear-shoulder, front-armpit in horizontal motion each. In the movement of each datum points by length, the check-result gained by checking the notice between motions shows that the most remarkable item is the front-shoulder.

• Composites Research
• /
• 제17권4호
• /
• pp.68-73
• /
• 2004

본 논문에서는 한 쪽 면만 복합재 패치로 보강한 알루미늄 균열평판의 피로균열 진전거동을 해석적인 방법으로 고찰하였다. 한쪽 면 보강 시, 균열선단은 비대칭성과 면 외 굽힘의 효과로 인하여 초기의 직선형태에서 경사곡선형태로 진전한다는 사실을 이전의 연구견과에서 확인할 수 있다. 따라서 정확한 피로거동을 고찰하기 위하여는 이와 같은 균열선단의 변화과정을 예측하고, 이론 해석에 반영하는 것이 필수적이라 하겠다. 본 연구에서는 균열선단 전개형상을 고려한 한쪽 면 보강시의 피로해석을 수행하기 위하여 선형탄성 파괴역학개념을 적용한 3차원 순차적 유한요소 해석기법을 적용하였는데, 이를 통하여 진전하는 균열선단 형상을 단계적, 반복적으로 추적하고 해석모델에 반영하였다. 이와 같은 해석기법을 적용함으로써 패치보강 평판의 피로수명은 물론 균열선단 진전과정도 정확히 예측할 수 있었다. 해석으로 얻어진 균열선단 진전거동 및 피로수명은 상응하는 실험결과와 잘 일치함을 확인하였다.

• 복식문화연구
• /
• 제14권2호
• /
• pp.271-285
• /
• 2006

The purpose of this study was to develop a new basic skirt pattern for 4 lower body types of Plus-sized women. To reduce a time and economic loss about putting it on, This study applied a 3D sample module in the course to develop a basic skirt pattern which is fit, functional and beautiful. A data analysis used the SPSS 11.0 statistics program. To verify the difference, This study used the variance analysis and Duncan's test for the postmortem verification. The result was as follows. To reflect a feature according to an abdomen projection and hip projection, we added the maximum hip circumference to the waist circumference and hip circumference for necessary for a skirt draft item. The front hip circumference sets to the H/4+1cm(ease)+D/4. The back hip circumference set to the H/4+0.5cm(ease)+D/4. The D is the hip circumference in the maximum hip circumference to subtract. The front waist circumference sets to the W/4+0.5cm(ease)+0.5cm(A front and back's difference)+D/4. The back waist circumference sets to the W/4+0.5cm(ease)-0.5cm(A front and back's difference)-D/4. Compare with 4 lower body types of Plus-sized Women, A type 2 and type 4 abdomen projections are bigger. We raised a front waistline of skirt pattern to a 0.3cm upside, and take about 1.3cm down the skirt length from a developed skirt pattern. Consequently, the appearance of a front skirt length was improved with a side skirt length.

• 한국의류산업학회지
• /
• 제21권2호
• /
• pp.189-202
• /
• 2019

This study develops a bodice pattern for high school girls aged 17 to 19 that use virtual garment simulation. The study developed a bodice pattern based on the fit evaluation result for two selected bodice patterns. The basic formula of the design method based on the result of 3 times of fit evaluation is as follows: waist back $length=stature/8{\times}1.85cm$, waist front length=waist back length+bust/40+0.7cm, front bust girth=bust/2+4cm, back bust girth=Chest/2+3cm, armscye depth=Chest/4+0.5cm, back interscye length=bishoulder length -1.2cm, front interscye length=back interscye length -1.2cm, front neck width=back neck width -0.3cm. The developed bodice pattern used Bishoulder Length as a criteria for the calculation formula of back interscye length, and back interscye length as a criteria for the calculation formula of front interscye length. The fit evaluation showed the relevance of the bishoulder length, front interscye length, and back interscye length based on a comparison of the calculated figure. A bodice pattern with great body suitability and fitness to high school girls was developed through 3D virtual garment simulation that calculated the application of body proportion to width. This study only analyzed the evaluation result of a virtual model only in a representative form; however, a pattern study is also proposed to compare and analyze the design methods of patterns by body type.

• 한국기계가공학회지
• /
• 제18권3호
• /
• pp.26-32
• /
• 2019

This study was conducted to analyze the stresses by impact loads on front-end loaders attached to tractors using flexible multi-body dynamics. The model was designed and validated by comparing previous experimental data with the simulation data obtained in this study. Nine sets of conditions were designed using three weights (500, 300, and 100 kg) loaded inside a bucket and three heights (1700, 1350, and 1000 mm) of the bucket from ground level. A parametric study was carried out at five locations for two types of parts of a front-end loader. All the safety factors for the five locations under all conditions were calculated and were greater than 1. Thus, the designs of the front-end loaders were structurally safe. Based on this study, front-end loaders attached to tractors can be designed effectively in terms of cost and safety.

• 한국재료학회지
• /
• 제27권10호
• /
• pp.518-523
• /
• 2017

In commercial solar cells, the pattern of the front electrode is critical to effectively assemble the photo generated current. The power loss in solar cells caused by the front electrode was categorized as four types. First, losses due to the metallic resistance of the electrode. Second, losses due to the contact resistance of the electrode and emitter. Third, losses due to the emitter resistance when current flows through the emitter. Fourth, losses due to the shading effect of the front metal electrode, which has a high reflectance. In this paper, optimizing the number of finger on a $4{\times}4$ solar cell is demonstrated with known theory. We compared the short circuit current density and fill factor to evaluate the power loss from the front metal contact calculation result. By experiment, the short circuit current density($J_{sc}$), taken in each pattern as 37.61, 37.53, and $37.38mA/cm^2$ decreased as the number of fingers increased. The fill factor(FF), measured in each pattern as 0.7745, 0.7782 and 0.7843 increased as number of fingers increased. The results suggested that the efficiency(Eff) was measured in each pattern as 17.51, 17.81, and 17.84 %. Throughout this study, the short-circuit current densities($J_{sc}$) and fill factor(FF) varied according to the number of fingers in the front metal pattern. The effects on the efficiency of the two factors were also investigated.

• 한국수산과학회지
• /
• 제47권4호
• /
• pp.424-430
• /
• 2014

Two major temperature fronts, the Subpolar (Gosung, Gang-won-do; $38^{\circ}-41^{\circ}N$) and Thermal (Jukbyun, Gyeong-sang-buk-do; $36^{\circ}-37^{\circ}N$) fronts, are found in the East Sea along the east coast of Korea. These are located roughly where the Tsushima Warm Current and North Korea Cold Current intersect. To clarify the effect of the Thermal Front, we investigated seasonal variation in fish species composition using set nets in two areas located north (Jangho, Gang-won-do) and south (Hupo, Gyeong-sang-buk-do) of Jukbyun, Gyeong-sang-buk-do, and compared the sea water temperature and salinity. We collected a total of 38 fish species in Hupo and 25 in Jangho. Trachurus japonicus was the most common species at both sites, but the subdominant species differed. At Hupo, the subdominant species were Konosirus punctatus and Diodon holocanthus, whereas Clupea pallasii and Scomber japonicus were subdominant at Jangho. Based on Froese and Pauly (2014), subtropical fishes accounted for 55% of fish in Hupo but only for 33% in Jangho. The difference in fish species composition was most obvious in May and August. According to the Korea Hydrographic and Oceanographic Administration, sea surface temperature and salinity were slightly higher at Hupo than at Jangho. Our findings suggest that the oceanographic boundary resulting from the Thermal Front near Jukbyun, Gyeong-sang-bukdo may have a major effect on the distribution of migratory fish species.

• 한국산업정보학회논문지
• /
• 제18권5호
• /
• pp.15-18
• /
• 2013

본 논문은 뇌전도 신호 처리를 위한 아날로그 전단부를 제시한다. 일반적으로 뇌전도 신호는 낮은 주파수 대역에 존재하고 신호의 크기가 미약하므로 이를 처리하기 위한 아날로그 전단부는 높은 전압 이득 및 공통모드 제거비를 가져야 하며 저주파 잡음을 효과적으로 억제해야 한다. 본 논문에서 제시하는 아날로그 전단부는 가변 이득 계측 증폭기와 대역통과 필터로 구성되어 있다. 낮은 주파수의 잡음을 제거하기 위하여 주파수 chopping을 적용하였다. 본 논문의 회로는 0.18um CMOS 공정을 이용하여 제작하였으며 측정 결과 최대 60dB의 전압이득과 100dB 이상의 공통모드 제거비를 내는 것을 확인하였다.