• Journal of Korea Water Resources Association
• /
• v.56 no.4
• /
• pp.285-299
• /
• 2023

Estimating the evapotranspiration is very important factor for effective water resources management, and FAO Penman-Monteith (FAO P-M) model has been applied for reference evapotranspiration estimation by many researchers. However, because various input data are required for the application of FAO P-M model, understanding the effect of each input data on FAO P-M model is necessary. Therefore, in this study, for 56 study stations located in South Korea, the effects of 8 meteorological factors (maximum and minimum temperature, wind speed, relative humidity, solar radiation, vapor pressure deficit, net radiation, ground heat flux), energy and aerodynamic terms of FAO P-M model, and elevation on FAO P-M reference evapotranspiration (RET) estimation were analyzed. The relative sensitivity analysis was performed to determine how 10% increment of each specific independent variable affects a reference evapotranspiration under given set of condition that other independent variables are unchanged. Furthermore, to select the 5 representative stations and perform the monthly relative sensitivity analysis for those stations, 56 study stations were classified into 5 clusters using cluster analysis. The study results showed that net radiation was turned out to be the most sensitive factor in 8 meteorological factors for 56 study stations. The next most sensitive factor was relative humidity, solar radiation, maximum temperature, vapor pressure deficit and wind speed, followed by minimum temperature in order. Ground heat flux was the least sensitive factor. In case of ground surface condition, elevation showed very low positive relative sensitivity. Relativity sensitivities of energy and aerodynamic terms of FAO P-M model were 0.707 for energy term and 0.293 for aerodynamic term respectively, indicating that energy term was more contributable than aerodynamic term for reference evapotranspiration. The monthly relative sensitivities of meteorological factors showed the seasonal effects, and also the relative sensitivity of elevation showed different pattern each other among study stations. Therefore, for the application of FAO P-M model, the seasonal and regional sensitivity differences of each input variable should be considered.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.1
• /
• pp.57-70
• /
• 2009

Considerable advance has been made on research on effect of steel pipe Umbrella Arch Method (UAM) and mechanical reinforcement mechanism through numerical analyses and experiments. Due to long analysis time of three-dimensional analysis and its complexity, un-quantitative two-dimensional analysis is dominantly used in the design and application, where equivalent material properties of UAM reinforced area and ground are used, For this reason, development of reasonable, theoretical, quantitative and easy to use design and analysis method is required. In this study, both field UAM tests and laboratory tests were performed in the residual soil to highly weathered rock; field tests to observe the range of reinforcement, and laboratory tests to investigate the change of material properties between prior to and after UAM reinforcement. It has been observed that the increase in material property of neighboring ground is negligible, and that only stiffness of steel pipe and cement column formed inside the steel pipe and the gap between steel pipe and borehole contributes to ground reinforcement. Based on these results and concept of Convergence Confinement Method (CCM), two dimensional axisymmetric analyses have been performed to obtain the longitudinal displacement profile (LDP) corresponding to arching effect of tunnel face, UAM effect and effect of supports. In addition, modified load distribution method in two dimensional plane-strain analysis has been suggested, in which effect of UAM is transformed to internal pressure and modified load distribution ratios are suggested. Comparison between the modified method and conventional method shows that larger displacement occur in the conventional method than that in the modified method although it may be different depending on ground condition, depth and size of tunnel, types of steel pipe and initial stress state. Consequently, it can be concluded that the effect of UAM as a beam in a longitudinal direction is not considered properly in the conventional method.

• Tuberculosis and Respiratory Diseases
• /
• v.49 no.5
• /
• pp.624-632
• /
• 2000

Background : Home ventilation can decrease hospital-acquired infection, increase physical activity, improve nutritional status, enhance quality of life, and reduce medical costs. The number of patient using home ventilators has been increasing, particularly in Europe and United States. Although the number of patients with home ventilation has been increasing in Korea, the current status of these patients is not well known. This study was undertaken to obtain basic information upon these patients in addition to evaluating any problems related to patients' home care in our country. Methods : A register of 92 patients with home ventilators in Seoul and Kyunggi Province were obtained from commercial ventilator supply companies. The patients were contacted by phone and 29 of them accepted our visit. Information concerning education about home care before discharge, equipment cost, and problems related to home care were documented. The mode and preset variables of the home ventilator were checked; tidal volume (TV), peak airway pressure, and oxygen saturation were measured. Results : There were 26 males (90%) and their mean age was 48.0 (${\pm}20.1$) years. The underlying diseases were : 21 neuromuscular disorders, 2 spinal cord injuries, 6 chronic lung diseases. Among the caregivers, spouses (n=14) predominated. Education for home care before discharge was performed primarily by intensive care unit nurses and the education for ventilator management by commercial companies. Twenty-five of the 29 patients had tracheostomies. Volume targeted type (VTT ; n=20, 69%) was more frequently used than the pressure targeted type (PTT). Twenty-three of the 29 patients purchased a ventilator privately, which cost 7,450,000 (${\pm}$3,290,000) won for a PTT, and 14,280.000 (${\pm}$3,130,000) won for a VTT. Total cost for the equipment was 11,430,000 (${\pm}$634,000) won. The average cost required for home care per month was 1,120,000 (${\pm}$1,360, 000) won. Conclusion : The commonest underlying disease of the patients was neuromuscular disease. The VTT ventilator was primarily used with tracheostomy. Patients and their families considered the financial difficulties associated with purchasing and maintaining equipment for home care an urgent problem. Some patients were aided by a visiting nurse, however most patients were neglected and left without professional medical supervision.

• Journal of Chest Surgery
• /
• v.37 no.4
• /
• pp.313-321
• /
• 2004

Excellent clinical results of the arterial switch operation and the limited availablity of the intraventricular rerouting has recently made an arterial switch operation to become the therapeutic method of choice for the repair of double-outlet right ventricle (DORV) with subpulmonary ventricular septal defect (VSD). The early and midterm outcomes of arterial switch operation for this anomaly were evaluated. Material and Method: Between August 1994 and July 2002, 13 patients underwent an arterial switch operation for the correction of double-outlet right ventricle with subpulmonary VSD at Dong-A university hospital.. The 50% rule was used to define DORV. Median age and mean body weight were 27 days (range, 3-120 days) and 3.8$\pm$0.7kg (range, 2.92-5.3kg) respectively. Aortic arch anomalies were associated in 6 cases (46.2%), which were all repaired through one-stage operation. The relationship of the great arteries were side-by-side in 8 cases (61.5%) and anteroposterior in 5 (38.5%). Coronary artery patterns were 1 LCx-2R in 6 cases, retropulmonary left coronary artery (LCA) in 6, and intramural LCA in 1 respectively. The enlargement of VSD was required in 1 patient and the patch enlargement of right ventricular outflow tract was performed in another one patient. The Lecompte maneuver was used in all but 3 patients with a side by side relationship of the great arteries. Result: Overall postoperative hospital mortality was 23.1 % (3/13). All operative deaths were occurred in the patients with aortic arch anomalies. There was one late death related to the postoperative complication of the central nerve system during the mean follow-up of 41.3$\pm$30.7 months. Pulmonary valvar stenosis (＞30mmHg of pressure gradient) developed in 1 patient (10%) and left pulmonary artery stenosis in 2 (20%), among them, one required reoperation 52 months after repair. There was an asymptomatic patient with moderate aortic regurgitation. 5-year survival rate including operative deaths was 68.3%. Conclusion: Although the operative mortality is high in the patients with aortic arch anomaly, the arterial switch operation for DORV with supbpulmonary VSD can be performed with low operative mortality and low reoperation rate in the patients Without arch anomaly. The arterial switch operation can be considered a good option for this complex anomaly.

• Journal of Chest Surgery
• /
• v.40 no.3 s.272
• /
• pp.193-199
• /
• 2007

Background: Reoperation is usually required for a right ventricle to pulmonary artery conduit obstruction caused by valve degeneration, conduit peel formation or somatic growth of the patient. An autologous tissue reconstruction (peel operation), where a prosthetic roof is placed over the fibrotic tissue bed of the explanted conduit, has been used to manage conduit obstructions at our institute since May 2002. Herein, the early and midterm results are evaluated. Material and Method: Between May 2002 and July 2006, 9 patients underwent obstructed extracardiac conduit replacement with an autologous tissue reconstruction, at a mean of 5.1 years after a Rastelli operation. The mean age at reoperation was $7.5{\pm}2.4$ years, ranging from 2.9 to 10.1 years. The diagnoses included 6 pulmonary atresia with VSD, 2 truncus arteriosus and 1 transposition of the great arteries. The preoperative mean systolic gradient was $88.3{\pm}22.2mmHg$, ranging from 58 to 125 mmHg. The explanted conduits were all Polystan valved pulmonary conduit (Polystan, Denmark). A bioprosthetic valve was inserted in 8 patients, and a monocusp ventricular outflow patch (MVOP) was used in 1 patient. The anterior wall was constructed with a Gore-Tex patch (n=7), MVOP (n=1) and bovine pericardium (n=1). Pulmonary artery angioplasty was required in 5 patients and anterior aortopexy in 2. The mean cardiopulmonary bypass time . was 154 minutes, ranging from 133 to 181 minutes; an aortic crossclamp was not performed in all patients. The mean follow-up duration was 20 months, ranging from 1 to 51 months. All patients were evaluated for their right ventricular outflow pathway using a 3-D CT scan. Resuit: There was no operative mortality or late death. The mean pressure gradient, assessed by echocardiography through the right ventricular outflow tract, was 20.4 mmHg, ranging from 0 to 29.6 mmMg, at discharge and 26 mmHg, ranging from 13 to 36 mmHg, at the latest follow-up (n=7, follow-up duration >1 year). There were no pseudoaneurysms, strictures or thrombotic occlusions. Conclusion: A peel operation was concluded to be a safe and effective re-operative option for an obstructed extracardiac conduit following a Rastelli operation.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.6
• /
• pp.265-274
• /
• 2021

Outlier detection research in ocean data has traditionally been performed using statistical and distance-based machine learning algorithms. Recently, AI-based methods have received a lot of attention and so-called supervised learning methods that require classification information for data are mainly used. This supervised learning method requires a lot of time and costs because classification information (label) must be manually designated for all data required for learning. In this study, an autoencoder based on unsupervised learning was applied as an outlier detection to overcome this problem. For the experiment, two experiments were designed: one is univariate learning, in which only SST data was used among the observation data of Deokjeok Island and the other is multivariate learning, in which SST, air temperature, wind direction, wind speed, air pressure, and humidity were used. Period of data is 25 years from 1996 to 2020, and a pre-processing considering the characteristics of ocean data was applied to the data. An outlier detection of actual SST data was tried with a learned univariate and multivariate autoencoder. We tried to detect outliers in real SST data using trained univariate and multivariate autoencoders. To compare model performance, various outlier detection methods were applied to synthetic data with artificially inserted errors. As a result of quantitatively evaluating the performance of these methods, the multivariate/univariate accuracy was about 96%/91%, respectively, indicating that the multivariate autoencoder had better outlier detection performance. Outlier detection using an unsupervised learning-based autoencoder is expected to be used in various ways in that it can reduce subjective classification errors and cost and time required for data labeling.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.13 no.1
• /
• pp.2206-2217
• /
• 1971

Spillway and discharge channel of reservoirs require the Control of Large volume of water under high pressure. The energies at the downstream end of spillway or discharge channel are tremendous. Therefore, Some means of expending the energy of the high-velocity flow is required to prevent scour of the riverbed, minimize erosion, and prevent undermining structures or dam it self. This may be accomplished by Constructing an energy dissipator at the downstream end of spillway or discharge channel disigned to dissipated the excessive energy and establish safe flow Condition in the outlet channel. There are many types of energy dissipators, stilling basins are the most familar energy dissipator. In the stilling basin, most energies are dissipated by hydraulic jump. stilling basins have some length to cover hydraulic jump length. So stilling basins require much concrete works and high construction cost. Flip bucket type energy dissipators require less construction cost. If the streambed is composed of firm rock and it is certain that the scour will not progress upstream to the extent that the safety of the structure might be endangered, flip backet type energy dissipators are the most recommendable one. Following items are tested and studied with bucket radius, $R=7h_2$,(medium of $4h_2{\geqq}R{\geqq}10h_2$). 1. Allowable upstream channel slop of bucket. 2. Adequate bucket lip angle for good performance of flip bucket. Also followings are reviwed. 1. Scour by jet flow. 2. Negative pressure distribution and air movement below nappe flow. From the test and study, following results were obtained. 1. Upstream channel slope of bucket (S=H/L) should be 0.25<H/L<0.75 for good performance of flip bucket. 2. Adequated lip angle $30^{\circ}{\sim}40^{\circ}$ are more reliable than $20^{\circ}{\sim}30^{\circ}$ for the safety of structures.

• Korean Journal of Agricultural Science
• /
• v.6 no.2
• /
• pp.166-184
• /
• 1979

In order to prevent the water loss in the irrigation canal constructed on the sandy gravel layer or on the other highly permeable ground layer, lining has been practiced. Many studies have been done so far on the lining method to prevent the water loss in the irrigation canal and recently studies on the lining with plastic film or polyethylene film were also reported. However, the plastic film or polyethylene film has low strength and is liable to break, and water loss from pin hole caused by contacting with sand or gravel is highly predicted. This study was then conducted to find proper lining and buring method in canal construction of polypropylene mat after coated with vinyl, as one way to overcome the shortcoming frequently observed when plastic or usual polyehtylene film were used. Eventhough rather longer periods of experiments are needed to attain reliable and accurate results on the variation of durability, the durability of asphalt coated area, or on the damage due to freeze after burial or exposure of polypropylene mat, the experiemental results obtained during one year of period are summarized as follows: 1. The curvature at the area between canal bottom and side slope had increased stability and saved consruction cost. The relationship among the variation of curvature, the reduction of polypropylene mat and the reduced amount of soil cutting at each side slope was presented in Fig. 7 through 9. 2. The depth of covering material to protect polypropylene mat was desired to be over 30cm, considering the water depth, side slope, canal cleaning practices, traffic, or back pressure of irrigation period. 3. In order to increase the canal stability and to prevent slope erosion, sandy soil was required, to be placed under ground, and coarse gravel should cover the surface area of canal. 4. The studies on the stability of side slope in the canal should consider the passive area on the bottom and the slope should be about 1 to 2, considering the slope stability, allowable velocity and tractive force. 5. When compared with earth lining, the lining with polypropylene mat coated with vinyl was responsible to save 28% and 37% of canal lining cost, when the soil carrying distances were 500 and 700m. respectively. 6. The water interception was almost completely attained when the polypropylene mat coated with vinyl was used for lining. But further studies were assumed to be necessary for the use of asphalt since the strength of polypropylene mat connected with asphalt will vary with duration.

• KDI Journal of Economic Policy
• /
• v.12 no.1
• /
• pp.31-68
• /
• 1990

The concentration of economic power takes the form of one or a few firms controlling a substantial portion of the economic resources and means in a certain economic area. At the same time, to the extent that these firms are owned by a few individuals, resource allocation can be manipulated by them rather than by the impersonal market mechanism. This will impair allocative efficiency, run counter to a decentralized market system and hamper the equitable distribution of wealth. Viewed from the historical evolution of Western capitalism in general, the concentration of economic power is a paradox in that it is a product of the free market system itself. The economic principle of natural discrimination works so that a few big firms preempt scarce resources and market opportunities. Prominent historical examples include trusts in America, Konzern in Germany and Zaibatsu in Japan in the early twentieth century. In other words, the concentration of economic power is the outcome as well as the antithesis of free competition. As long as judgment of the economic system at large depends upon the value systems of individuals, therefore, the issue of how to evaluate the concentration of economic power will inevitably be tinged with ideology. We have witnessed several different approaches to this problem such as communism, fascism and revised capitalism, and the last one seems to be the only surviving alternative. The concentration of economic power in Korea can be summarily represented by the "jaebol," namely, the conglomerate business group, the majority of whose member firms are monopolistic or oligopolistic in their respective markets and are owned by particular individuals. The jaebol has many dimensions in its size, but to sketch its magnitude, the share of the jaebol in the manufacturing sector reached 37.3% in shipment and 17.6% in employment as of 1989. The concentration of economic power can be ascribed to a number of causes. In the early stages of economic development, when the market system is immature, entrepreneurship must fill the gap inherent in the market in addition to performing its customary managerial function. Entrepreneurship of this sort is a scarce resource and becomes even more valuable as the target rate of economic growth gets higher. Entrepreneurship can neither be readily obtained in the market nor exhausted despite repeated use. Because of these peculiarities, economic power is bound to be concentrated in the hands of a few entrepreneurs and their business groups. It goes without saying, however, that the issue of whether the full exercise of money-making entrepreneurship is compatible with social mores is a different matter entirely. The rapidity of the concentration of economic power can also be traced to the diversification of business groups. The transplantation of advanced technology oriented toward mass production tends to saturate the small domestic market quite early and allows a firm to expand into new markets by making use of excess capacity and of monopoly profits. One of the reasons why the jaebol issue has become so acute in Korea lies in the nature of the government-business relationship. The Korean government has set economic development as its foremost national goal and, since then, has intervened profoundly in the private sector. Since most strategic industries promoted by the government required a huge capacity in technology, capital and manpower, big firms were favored over smaller firms, and the benefits of industrial policy naturally accrued to large business groups. The concentration of economic power which occured along the way was, therefore, not necessarily a product of the market system. At the same time, the concentration of ownership in business groups has been left largely intact as they have customarily met capital requirements by means of debt. The real advantage enjoyed by large business groups lies in synergy due to multiplant and multiproduct production. Even these effects, however, cannot always be considered socially optimal, as they offer disadvantages to other independent firms-for example, by foreclosing their markets. Moreover their fictitious or artificial advantages only aggravate the popular perception that most business groups have accumulated their wealth at the expense of the general public and under the behest of the government. Since Korea stands now at the threshold of establishing a full-fledged market economy along with political democracy, the phenomenon called the concentration of economic power must be correctly understood and the roles of business groups must be accordingly redefined. In doing so, we would do better to take a closer look at Japan which has experienced a demise of family-controlled Zaibatsu and a success with business groups(Kigyoshudan) whose ownership is dispersed among many firms and ultimately among the general public. The Japanese case cannot be an ideal model, but at least it gives us a good point of departure in that the issue of ownership is at the heart of the matter. In setting the basic direction of public policy aimed at controlling the concentration of economic power, one must harmonize efficiency and equity. Firm size in itself is not a problem, if it is dictated by efficiency considerations and if the firm behaves competitively in the market. As long as entrepreneurship is required for continuous economic growth and there is a discrepancy in entrepreneurial capacity among individuals, a concentration of economic power is bound to take place to some degree. Hence, the most effective way of reducing the inefficiency of business groups may be to impose competitive pressure on their activities. Concurrently, unless the concentration of ownership in business groups is scaled down, the seed of social discontent will still remain. Nevertheless, the dispersion of ownership requires a number of preconditions and, consequently, we must make consistent, long-term efforts on many fronts. We can suggest a long list of policy measures specifically designed to control the concentration of economic power. Whatever the policy may be, however, its intended effects will not be fully realized unless business groups abide by the moral code expected of socially responsible entrepreneurs. This is especially true, since the root of the problem of the excessive concentration of economic power lies outside the issue of efficiency, in problems concerning distribution, equity, and social justice.

• Asia pacific journal of information systems
• /
• v.21 no.4
• /
• pp.63-104
• /
• 2011

The study examines the relationships among employee's goal orientation, IT personnel competency, personal effectiveness. The goal orientation includes learning goal orientation, performance approach goal orientation, and performance avoid goal orientation. Personal effectiveness consists of personal work satisfaction and personal work performance. In general, IT personnel competency refers to IT expert's skills, expertise, and knowledge required to perform IT activities in organizations. However, due to the advent of the internet and the generalization of IT, IT personnel competency turns out to be an important competency of technological experts as well as employees in organizations. While the competency of IT itself is important, the appropriate harmony between IT personnel's business capability and technological capability enhances the value of human resources and thus provides organizations with sustainable competitive advantages. The rapid pace of organization change places increased pressure on employees to continually update their skills and adapt their behavior to new organizational realities. This challenge raises a number of important questions concerning organizational behavior? Why do some employees display remarkable flexibility in their behavioral responses to changes in the organization, whereas others firmly resist change or experience great stress when faced with the need to alter behavior? Why do some employees continually strive to improve themselves over their life span, whereas others are content to forge through life using the same basic knowledge and skills? Why do some employees throw themselves enthusiastically into challenging tasks, whereas others avoid challenging tasks? The goal orientation proposed by organizational psychology provides at least a partial answer to these questions. Goal orientations refer to stable personally characteristics fostered by "self-theories" about the nature and development of attributes (such as intelligence, personality, abilities, and skills) people have. Self-theories are one's beliefs and goal orientations are achievement motivation revealed in seeking goals in accordance with one's beliefs. The goal orientations include learning goal orientation, performance approach goal orientation, and performance avoid goal orientation. Specifically, a learning goal orientation refers to a preference to develop the self by acquiring new skills, mastering new situations, and improving one's competence. A performance approach goal orientation refers to a preference to demonstrate and validate the adequacy of one's competence by seeking favorable judgments and avoiding negative judgments. A performance avoid goal orientation refers to a preference to avoid the disproving of one's competence and to avoid negative judgements about it, while focusing on performance. And the study also examines the moderating role of work career of employees to investigate the difference in the relationship between IT personnel competency and personal effectiveness. The study analyzes the collected data using PASW 18.0 and and PLS(Partial Least Square). The study also uses PLS bootstrapping algorithm (sample size: 500) to test research hypotheses. The result shows that the influences of both a learning goal orientation (${\beta}$ = 0.301, t = 3.822, P < 0.000) and a performance approach goal orientation (${\beta}$ = 0.224, t = 2.710, P < 0.01) on IT personnel competency are positively significant, while the influence of a performance avoid goal orientation(${\beta}$ = -0.142, t = 2.398, p < 0.05) on IT personnel competency is negatively significant. The result indicates that employees differ in their psychological and behavioral responses according to the goal orientation of employees. The result also shows that the impact of a IT personnel competency on both personal work satisfaction(${\beta}$ = 0.395, t = 4.897, P < 0.000) and personal work performance(${\beta}$ = 0.575, t = 12.800, P < 0.000) is positively significant. And the impact of personal work satisfaction(${\beta}$ = 0.148, t = 2.432, p < 0.05) on personal work performance is positively significant. Finally, the impacts of control variables (gender, age, type of industry, position, work career) on the relationships between IT personnel competency and personal effectiveness(personal work satisfaction work performance) are partly significant. In addition, the study uses PLS algorithm to find out a GoF(global criterion of goodness of fit) of the exploratory research model which includes a mediating variable, IT personnel competency. The result of analysis shows that the value of GoF is 0.45 above GoFlarge(0.36). Therefore, the research model turns out be good. In addition, the study performs a Sobel Test to find out the statistical significance of the mediating variable, IT personnel competency, which is already turned out to have the mediating effect in the research model using PLS. The result of a Sobel Test shows that the values of Z are all significant statistically (above 1.96 and below -1.96) and indicates that IT personnel competency plays a mediating role in the research model. At the present day, most employees are universally afraid of organizational changes and resistant to them in organizations in which the acceptance and learning of a new information technology or information system is particularly required. The problem is due' to increasing a feeling of uneasiness and uncertainty in improving past practices in accordance with new organizational changes. It is not always possible for employees with positive attitudes to perform their works suitable to organizational goals. Therefore, organizations need to identify what kinds of goal-oriented minds employees have, motivate them to do self-directed learning, and provide them with organizational environment to enhance positive aspects in their works. Thus, the study provides researchers and practitioners with a matter of primary interest in goal orientation and IT personnel competency, of which they have been unaware until very recently. Some academic and practical implications and limitations arisen in the course of the research, and suggestions for future research directions are also discussed.