• Journal of Practical Agriculture & Fisheries Research
• /
• v.3 no.1
• /
• pp.70-78
• /
• 2001

The objective of this study was to determine effects of corn germ meal(CGM) and condensed molasses fermentation solubles(CMS) as the replacement of rice bran on mycelial growth and density in various mushrooms. The results of this study showed that CGM and CMS might be utilized more efficiently than rice bran in culturing mushrooms. The results are as follows; 1. Mycelial growth of Pleurotus ostreatus was remarkably higher than that of control when the concentration of CGM and CMS was 10%, respectively. However, the mycelial density was lower than that of control. Thus, Considering the mycelial growth as well as density, it was found that 20% supplements of CGM and CMS resulted in the best with 78mm/10d and 71mm/10d, respectively. 2. Mycelial growth of Pleurotus eryngii in the treatment group of 10% CMS and 20% CGM showed 74mm/10d and 67mm/10d, respectively. This result tended to be equal or somewhat lower compared with that of control(74mm/10d). 3. Mycelial growth of Flamulina velutipes was 87mm/10d in the treatment of 10% CMS, 79mm/10d in the treatment of 20% CGM, which showed significantly higher than that of control(56mm/10d). When the contents of CGM and CMS were mixed with the amount of 10-30%, Thus, it was assumed that the quantity of mushrooms may increase with the supplements of CEM and CMS. 4. Mycelial growth of Lentinus edodes in the treatment group of 10-40% CMS and 10-30% CGM showed 58-52mm/10d and 56-49mm/10d, respectively. This result was significantly higher that control(47mm/10d). 5. When CMS and CGM were supplememted with the level of 10-30%, mycelial growth rate of Ganoderma lucidum showed 76-72mm/10d and 74-69mm/10d, respectively, which are higher than those of control.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.419-425
• /
• 2023

This paper presents the research results of analyzing the high-temperature corrosion characteristics of three currently commercialized heat exchanger tube materials under actual operating conditions of a biomass power plant. In order to precisely analyze the high-temperature corrosion characteristics of these materials, a high-temperature corrosion evaluation device was installed in the power plant equipment, which allows for adjusting the surface temperature of the heat exchanger tubes. Experiments were conducted for approximately 300 hours under various temperature and operating conditions. In this study, the commercialized heat exchanger tube materials used were SA213T12, SA213T22, and SA213T91 alloys. In order to objectively analyze the high-temperature corrosion characteristics of each material, an international standard-based process to remove corrosion products was applied to obtain the weight change of the specimens, and the average thickness loss and corrosion rate were derived. Thus, the high-temperature corrosion results for each condition were quantitatively compared and analyzed. In addition, in order to increase the reliability of the high-temperature corrosion evaluation method introduced in this study, the surface and cross-sectional corrosion of the specimens were confirmed by using scanning electron microscopy and energy-dispersive X-ray analysis. Based on these analysis results, it was found that the corrosion resistance of the commercial heat exchanger materials increases as the content of chrome and nickel in the composition increases. Additionally, it was found that the corrosion phenomenon is rapidly accelerated as the surface temperature increases. Finally, the replacement period (lifetime) of the heat exchanger tubes under each condition could be inferred through this study.

• Journal of Convergence Korean Medicine
• /
• v.3 no.1
• /
• pp.5-13
• /
• 2022

Objectives: Smoking had a long negative impact on public health. The ingredients of a cigarette are major risk factors for several diseases. Owing to the problems about economic and quality of life, we need to ensure smoking cessation (SC). There are several approaches for SC including pharmacological therapy, nicotine replacement therapy, education, and behavioral intervention. However, due to some limitations, other alternative approaches are gaining popularity. Acupuncture has been reported to have few side effects and be more effective than some conventional treatments in several articles. However, there are no systematic reviews on the comparison of acupuncture combination treatment with other conventional monotherapies. Methods: Randomized controlled trials that used acupuncture as an adjunct treatment for SC will be searched and data will be summarized according to the predefined criteria. The primary outcome will be the abstinence rate, and secondary outcomes will be adverse events and biochemical indicators. We will use Review Manager to perform a meta-analysis, Cochrane Collaboration Risk of Bias tool for the risk of bias assessment, and the Grades of Recommendation, Assessment, Development and Evaluation approach to determine the quality of evidence. We will investigate the efficacy and safety of acupuncture combination treatment for SC with this study. Ethics and dissemination: This study will provide reliable clinical evidence on additional effect of acupuncture on smoking cessation. We will publish our results in a peer-review journal.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.75-89
• /
• 2006

This paper presents a practical and realistic Life-Cycle Cost (LCC) optimum design methodology of steel bridges considering time effect of bridge reliability under environmental stressors such as corrosion and heavy truck traffics. The LCC functions considered in the LCC optimization consist of initial cost, expected life-cycle maintenance cost and expected life-cycle rehabilitation costs including repair/replacement costs, loss of contents or fatality and injury losses, road user costs, and indirect socio-economic losses. For the assessment of the life-cycle rehabilitation costs, the annual probability of failure which depends upon the prior and updated load and resistance histories should be accounted for. For the purpose, Nowak live load model and a modified corrosion propagation model considering corrosion initiation, corrosion rate, and repainting effect are adopted in this study. The proposed methodology is applied to the LCC optimum design problem of an actual steel box girder bridge with 3 continuous spans (40 m+50 m+40 m=130 m), and various sensitivity analyses of types of steel, local corrosion environments, average daily traffic volume, and discount rates are performed to investigate the effects of various design parameters and conditions on the LCC-effectiveness. From the numerical investigation, it has been observed that local corrosion environments and the number of truck traffics significantly influence the LCC-effective optimum design of steel bridges, and thus realized that these conditions should be considered as crucial parameters for the optimum LCC-effective design.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.208-215
• /
• 1999

The creep behavior of a rapidly solidified and consolidated Al-9.45wt%Fe-4.45wt%Cr alloy were investigated in the stress range 40 to 115 MPa and temperature range 300(0.53Tm) to 441$^{\circ}C$(0.66Tm). It is of use to available aerospace and automobile industries for the improved performance of materials used at high temperature. Because Al alloys with improved creep resistance offer the potential for lower weight and reduced costs in aerospace and automobile components (e.g., structural members and engine parts) through the replacement of heavier and more costly materials, the safety in use at high temperature is good. The alloy is characterized by high stress exponents and activation energies for creep, which are greatly dependent on the stress and temperature. Because the creep stress is seen to cause a strongly significant enhancement of coarsening, the coarsening rate of the dispersed particles in all crept specimens is faster than that in isothermally annealed specimens. Dislocations connecting dispersoids are observed more cofrequently in crept specimens with higher stress and lower temperature. The creep strain rates in the power law creep regime were found to be predicted much better by the Shorty and Rosler/Arzt equation with the inclusion of a threshold stress and dislocation detachment mechanism. The dispersoids in this alloy were acting a source of void nucleation that finally leaded to ductile fracture within the grain so called intergranular. Each void was initiated, grown and failed at the dispersoids in the aluminium matrix. Grain boundary accommodation of the slip produced, which result in initiation of the void and then final transgranular fracture. Therefore, it was confirmed that these dispersoids played an important role in the fracture mechanism by the formation of $Al_{13}Fe_4$, $Al_{13}Cr_2$ and $Al_2O_3$.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.192-201
• /
• 2023

In this paper, the strength properties of porous concrete containing natural fine aggregates and bottom ash aggregates were investigated, The material properties of natural fine aggregates and bottom ash were identified then used as aggregates for porous concrete. The water-binder ratio was constant at 0.25, and the com paction level of 0.5, 1.5, and 2.5 MPa was applied to produce a porous concrete specimen. Test of unit weight, ultrasonic velocity, compressive strength, and flexural tensile strength were perform ed and analyzed. The unit weight, ultrasonic velocity, com pressive strength, and flexural tensile strength increased as the compaction level increased and also the replacement rate of bottom ash with sand(fine aggregate) increased. In addition, through regression analysis, the correlation between the unit weight, compressive strength, and flexural tensile strength of bottom ash porous concrete was presented. Unit weight and strength properties are proportional to each other and showed an increasing correlation. In addition, the correlation coefficient (R²) value of regression analysis was calculated based on the experimental results of this study and those of other research papers.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.425-432
• /
• 2023

In this study, we aim to develop a carbon-reducing concrete technology by incorporating biochar. Performance evaluation experiments were conducted on concrete mixtures containing biochar with insulating and carbon-capturing properties, which are essential for key infrastructure sectors such as construction and tunnels. Concrete mixtures were designed with different biochar incorporation rates of 0 %, 5 %, 10 %, 15 %, and 20 %, as w ell as w ater-to-binder ratios of 0.25, 0.30, 0.35, and 0.40. To assess the physical properties of each mixture, unit weight, total porosity, and permeability were measured, while mechanical properties were determined through the measurement of concrete compressive and flexural strengths. Key factors for enhancing the insulating effect of carbon-reducing concrete containing biochar were identified through regression analysis, indicating a close correlation among biochar incorporation rate, unit weight, concrete strength, and thermal conductivity. It is anticipated that it can be utilized as an insulating material to enhance thermal performance in northern regions with severe winter climates.

• Journal of the Korean Society of Radiology
• /
• v.84 no.6
• /
• pp.1324-1336
• /
• 2023

Purpose This study aimed to compare the diagnostic performance of cardiac CT and transthoracic echocardiogram (TTE) depending on the degree of valvular calcification and bicuspid aortic valve (BAV) subtype. Materials and Methods This retrospective study included 266 consecutive patients (106 with BAV and 160 with tricuspid aortic valve) who underwent cardiac CT and TTE before aortic valve replacement. Cardiac CT was used to evaluate the morphology of the aortic valve, and a calcium scoring scan was used to quantify valve calcium. The aortic valves were classified into fused and two-sinus types. The diagnostic accuracy of cardiac CT and TTE was calculated using a reference standard for intraoperative inspection. Results CT demonstrated significantly higher sensitivity, negative predictive value, and accuracy than TTE in detecting BAV (p < 0.001, p < 0.001, and p = 0.003, respectively). The TTE sensitivity tended to decrease as valvular calcification increased. The error rate of TTE for CT was 10.9% for the twosinus type of BAV and 28.3% for the fused type (p = 0.044). Conclusion Cardiac CT had a higher diagnostic performance in detecting BAV than TTE and may help diagnose BAV, particularly in patients with severe valvular calcification.

• Journal of the Korean Chemical Society
• /
• v.36 no.4
• /
• pp.565-578
• /
• 1992

It has been suggested that Hg$^{2+}$-promoted reaction of a series of cis-[Co(en)$_2$(L)Cl]$^{2+}$ (en = 1,2-diaminoethane) with L = NH$_3$, NH$_2$CH$_3$, glyOC$_2$H$_5$, glyOCH$_3$, dl-alaOC$_2$H$_5$, NH$_2$CH$_2$CONH$_2$, and NH$_2$CH$_2$CN proceeds by dissociative interchange(I$_d$) mechanism from kinetic data, circular dichroism spectra, analyses of products, and the values of m(Grunwald-Winstein plot) using Y (solvent ionizing power) in aqueous solution and in mixed aqueous-organic solvent. It has been found that chloride replacement by water (aquation) for the series with L = NH$_3$ and NH$_2$CH$_3$ and chelation of ligand L to Co(Ⅲ) for the series with L = glyOC$_2$H$_5$, glyOCH$_3$, dl-alaOC$_2$H$_5$, NH$_2$CH$_2$CONH$_2$, and NH$_2$CH$_2$CN occurs, respectively. The rate constants on Hg$^{2+}$-induced reaction of the series except cis-[Co(en)$_2$(NH$_2$CH$_2$CN)Cl]$^{2+}$ were increased with increasing the contents of ethanol in mixed water-ethanol solvents. In mixed water-30${\%}$ organic solvents, the rate constants of the series except cis-[Co(en)$_2$(NH$_2$CH$_2$CN)Cl]$^{2+}$ have also been measured in the order 30${\%}$ 2-propanol-water > 30${\%}$ ethanol-water > water. However, the rate constants of cis-[Co(en)$_2$(NH$_2$CH$_2$CN)Cl]$^{2+}$ were reversed. The rate constants of the series with L= NH$_3$ and NH$_2$CH$_3$ were related to ligand field parameter (${\Delta}$), but those of the series with L = glyOC$_2$H$_5$, glyOCH$_3$, dl-alaOC$_2$H$_5$, NH$_2$CH$_2$CONH$_2$, NH$_2$CH$_2$CN were not. The reaction between the series and Hg2+ in aqueous media containing NO$_3^-$ has been investigated. The results for the reaction do not alter the mechanism, but the rate only was altered.

• Journal of Chest Surgery
• /
• v.40 no.4 s.273
• /
• pp.280-287
• /
• 2007

Background: We retrospectively evaluated the clinical results of surgically managing patients with Ebstein's anomaly. Material and Method: Between Feb. f 984 and June 2006, 50 patients who underwent surgical treatment for Ebstein's anomaly at Yonsei Cardiovascular Center were retrospectively reviewed. The mean age of the patients was 26.9 years and 19 patients were male, Associated anomalies included atrial septal defect (33), patent ductus arteriosus (2), ventricular septal defect (1), and pulmonary stenosis (4), and 90%, (45/50) of the patients had more than a moderate degree of tricuspid regurgitation. Carpentier type A was present in 6 patients, type B in 26, type C in 14 and type D in 4. Ten patients were associated with WPW syndrome. Conservative surgery was possible in 31 patients (tricuspid annuloplasty, plication of the atrialized RV), Fontan's operation was peformed in 4 patients, tricuspid valve replacement was done in 12 and palliative surgery was done in 2 patients. Thirteen patients were associated with hi-directional cavopulmonary shunt (BCPS: one and a half ventricular repairs): 10 patients with WPW syndrome and 4 patients with atrial fibrillation underwent concomitant ablation. Result: The postoperative median NYHA functional class $(3{\rightarrow}1)$ and the mean cardio-thoracic ratio $(0.65{\rightarrow}0.59)$ were decreased significantly (p<0.001, p=0.014). The mean oxygen saturation $(86.6{\rightarrow}94.1%)$, and median TR grade $(4{\rightarrow}1)$ were also significantly improved (p=0.004, p<0.001). For comparison of BCPS and conservative surgery, the preoperative right ventricular pressure (33.0 vs. 41.3 mmHg), the ICU stay (2.80 vs. 1.89 days), the hospital say (10.6 vs. 16.8 days), and the left ventricular ejection fraction (64.3 vs. 72.8%) were statistically different. Postoperative mortality occurred in 3 patients (6%) due to biventricular failure in 2 patients and sepsis in the other patient. The mean follow up duration was 101.5 months, and one patient died of Fontan failure and 6 patients required reoperation (bioprosthetic degenerative change (2) and Fontan conversion (4)). The overall survival rate at 10 years was 90.2%, the freedom from reoperation rate and rate of cardiac related events were 78.9% and 49.2%, respectively. Conclusion: Surgical management of Ebstein's anomaly can be performed safely, and the associated BCPS may be helpful for high-risk patients. Adequate application of surgical management may increase the long-term survival with a reduced rate of reoperation.