• Journal of Microbiology and Biotechnology
• /
• v.22 no.3
• /
• pp.400-406
• /
• 2012

To improve the hydrogen yield from biological fermentation of organic wastewater, a co-culture system of dark- and photo-fermentation bacteria was investigated. In a pure-culture system of the dark-fermentation bacterium Clostridium butyricum, a pH of 6.25 was found to be optimal, resulting in a hydrogen production rate of 18.7 ml-$H_2/l/h$. On the other hand, the photosynthetic bacterium Rhodobacter sphaeroides could produce the most hydrogen at 1.81mol-$H_2/mol$-glucose at pH 7.0. The maximum specific growth rate of R. sphaeroides was determined to be 2.93 $h^{-1}$ when acetic acid was used as the carbon source, a result that was significantly higher than that obtained using either glucose or a mixture of volatile fatty acids (VFAs). Acetic acid best supported R. sphaeroides cell growth but not hydrogen production. In the co-culture system with glucose, hydrogen could be steadily produced without any lag phase. There were distinguishable inflection points in a plot of accumulated hydrogen over time, resulting from the dynamic production or consumption of VFAs by the interaction between the dark- and photo-fermentation bacteria. Lastly, the hydrogen production rate of a repeated fed-batch run was 15.9 ml-$H_2/l/h$, which was achievable in a sustainable manner.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.4
• /
• pp.473-482
• /
• 2013

The desulfurization ability of Sphingomonas subarctica T7b was evaluated using resting and immobilized cells with dibenzothiophene (DBT), alkyl DBTs, and commercial light gas oil (LGO) as the substrates. The resting cells of S. subarctica T7b degraded 239.2 mg of the initial 250 mg of DBT/l (1.36 mM) within 24 h at $27^{\circ}C$, while 127.5 mg of 2-hydroxybiphenyl (2-HBP)/l (0.75 mM) was formed, representing a 55% conversion of the DBT. The DBT desulfurization activity was significantly affected by the aqueous-to-oil phase ratio. In addition, the resting cells of S. subarctica T7b were able to desulfurize alkyl DBTs with long alkyl chains, although the desulfurization rate decreased with an increase in the total carbon number of the alkylated DBTs. LGO with a total sulfur content of 280 mg/l was desulfurized to 152 mg/l after 24 h of reaction. Cells immobilized by entrapment with polyvinyl alcohol (PVA) exhibited a high DBT desulfurization activity, including repeated use for more than 8 batch cycles without loss of biodesulfurization activity. The stability of the immobilized cells was better than that of the resting cells at different initial pHs, higher temperatures, and for DBT biodesulfurization in successive degradation cycles. The immobilized cells were also easily separated from the oil and water phases, giving this method great potential for oil biodesulfurization.

• Geomechanics and Engineering
• /
• v.37 no.1
• /
• pp.49-64
• /
• 2024

Rocks undergoing repeated loading and unloading over an extended period, such as due to earthquakes, human excavation, and blasting, may result in the gradual accumulation of stress and deformation within the rock mass, eventually reaching an unstable state. In this study, a CNN-CCM is proposed to address the mechanical behavior. The structure and hyperparameters of CNN-CCM include Conv2D layers × 5; Max pooling2D layers × 4; Dense layers × 4; learning rate=0.001; Epoch=50; Batch size=64; Dropout=0.5. Training and validation data for deep learning include 71 rock samples and 122,152 data points. The AI Rock Constitutive Model learned by CNN-CCM can predict strain values(ε₁) using Mass (M), Axial stress (σ₁), Density (ρ), Cyclic number (N), Confining pressure (σ₃), and Young's modulus (E). Five evaluation indicators R², MAPE, RMSE, MSE, and MAE yield respective values of 0.929, 16.44%, 0.954, 0.913, and 0.542, illustrating good predictive performance and generalization ability of model. Finally, interpreting the AI Rock Constitutive Model using the SHAP explaining method reveals that feature importance follows the order N > M > σ₁ > E > ρ > σ₃.Positive SHAP values indicate positive effects on predicting strain ε₁ for N, M, σ₁, and σ₃, while negative SHAP values have negative effects. For E, a positive value has a negative effect on predicting strain ε₁, consistent with the influence patterns of conventional physical rock constitutive equations. The present study offers a novel approach to the investigation of the mechanical constitutive model of rocks under cyclic loading and unloading conditions.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.5
• /
• pp.596-610
• /
• 2024

Since the creation of the first submarine telegraph cable connecting England and France in 1850, today, due to the rapid development of the Internet and Communications fields, the demand for submarine communication cables has increased and continues to develop. Submarine cables are designed and manufactured to be suitable for the maritime environment, and many parts are imported from overseas, and several domestic cable manufacturers are producing them for commercial purposes. Field-proven and reliable commercial submarine communication cable technology is also being applied to the military field, and is especially actively utilized in naval surface ships and submarines. This paper is about the design of an underwater cable applicable to submarine(KSS-III Bach-II) navigation radar and also is to secure the performance of an underwater cable with bending durability in extreme marine environments, emergency diving, and repeated mast raising and lowering. Finally, we hop that the domestic development of underwater cables will help improve the performance of navigation radars for submarines.

• Economic and Environmental Geology
• /
• v.48 no.6
• /
• pp.491-500
• /
• 2015

Batch experiments were performed to determine the feasibility of the surfactant-enhanced soil washing process at various washing conditions for the Kuwait soil seriously contaminated with the crude oil. The soil was sampled at a dried oil pond in Kuwait and its average TPH concentration was 223,754 mg/kg, which was too high to apply the conventional remediation process. Nine commercialized non-ionic surfactants were used for the batch experiment to measure the surfactant solubility for the crude oil because it was reported that they have worked for the soil remediation. Among them, three surfactants having high crude oil solubility were used for the soil washing experiment. From the result of batch experiment, 5% TritonX-100 washing solution showed the highest TPH removal efficiency (67%) for the crude oil contaminated soil. However, because the residual TPH concentration in the washed soil was still higher than the clean-up level in Kuwait (10,000 mg/kg), the repeated soil washing was performed. After five washings with 2% surfactant solution, the cumulative TPH removal efficiency was higher than 96% and the residual TPH concentration in the soil went down below the clean-up level. To measure the desorption capacity of TritonX-100 remained in the soil after the soil washing, the silica beads and the soil were washed five times with 2% TritonX-100 surfactant solution and then they were washed again with distilled water to detach the surfactant adsorbed on beads or soil. After five washings with surfactant solution, 7.8% and 19.6% of the surfactant was adsorbed on beads and soil, respectively. When additionally washed with distilled water, most of the residual surfactant were detached from beads and only 4.3% of surfactant was remained in soil. From the results, it was investigated that the surfactant-enhanced soil washing process with TritonX-100, Tergitol S-15-7, and Tergitol S-15-9 has a great capability for the remediation of the Kuwait soil seriously contaminated by crude oil (more than 220,000 mg/kg).

• Clean Technology
• /
• v.26 no.3
• /
• pp.221-227
• /
• 2020

When the waste solid fuel (SRF, Bio-SRF) is burnt in a boiler, a problem occurs in the combustion process involving the alkali components (Na, K) contained in large amounts in the fuel. The alkaline component has a low melting point, which usually forms low melting point salt in the temperature of the furnace, with the resulting low melting point salts attaching to the heat pipe to form a clinker. Various additives are used to suppress clinker generation, and the additive based on the kaolinite has alkali-aluminum-silica to inhibit the clinker. In this study, the reactivity of the additives based on the kaolinite was compared. The additives utilized were R-kaolinite, B-kaolinite, and A-kaolinite. Also silica and MgO were sourced as the comparison group. The experimental group was employed as a laboratory-scale batch horizontal reactor. The additive and alkaline salts were reacted at a weight ratio of 1 : 1, and the reaction temperature was performed at 900 ℃ for 10 hours. The first measurement of HCl occurring during the experiment was performed 30 minutes after the detection tube was used, and the process was repeated every hour after the experiment. After the reaction, solid residues were photographed for characterization analysis by means of an optical microscope. The reaction characteristics of the kaolinite were confirmed based on the analysis results.

• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.73-86
• /
• 1999

The ion-exchange method for the purification of primary coolant has been used broadly in PWR(pressurized water reactor)-type nuclear power plants due to its high decontamination efficiency, simple system, and easy operation. However, its non-selective removal of metal and non-radionuclides shortens its life, resulting in the generation of a large amount of waste ion-exchange resin. In this study, the feasibility of electrodeionization (EDI) was investigated for the purification of primary cooling water using synthetic solutions under various experimental conditions as an alternative method for the ion exchange. The results shows that as the feed flow-rate increased, the removal efficiency increased and the power consumption decreased. The removal rate was observed as a 1000 decontamination factor(DF) at a nearly constant level. For the synthetic solution of 3 ppm TDS (Total Dissolved Solid), the power consumption was 40.3 mWh/L at 2.0 L/min of feed flow rate. The higher removal rate of metal species and lower power consumption were obtained with greater resin volume per diluting compartment. However, the flow rate of the EDI process decreased with the elapsed time because of the hydrodynamic resistivity of resin itself and resin fouling by suspended solids. Thus, the ion-exchange resin was replaced by an ion-conducting spacer in order to overcome the drawback. The system equipped with the ion-conducting spacer resolved the problem of the decreasing flow rate but showed a lower efficiency in terms of the power consumption, the removal rate of metal species and current efficiency. In the repeated batch operation, it was found that the removal efficiency of metal species was stably maintained at DF 1000.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.4
• /
• pp.25-33
• /
• 2019

Operating characteristics of a 30 L microbial electrolysis cell (MEC) for producing biogas from sewage sludge was studied. During the 32-day inoculation period, carbon dioxide concentration decreased and methane concentration increased with operating time, and the overall methane content of biogas was 69.1% with a production rate of 171.6 mL CH₄/L·d. In fed-batch experiments for 6 operating cycles, CH₄ concentration of 66.5~77.2% was obtained at a production rate of 184.9~372.9 mL CH₄/L·d, COD, TS and VS removal efficiency ranged from 28.2 to 42.1%, 20.7 to 37.5% and 18.5 to 36.9%, respectively. The MEC system was observed to be stabilized as operating cycles were repeated after inoculation. In the last operating cycle, 5221 mL/L of methane was produced with CH₄ yield of 316.7 L CH₄/kg COD_rem, and the energy recovery was 73%.

• Journal of Korean Society on Water Environment
• /
• v.27 no.6
• /
• pp.926-931
• /
• 2011

Among various techniques for hydrogen production from organic wastewater, a dark fermentation is considered to be the most feasible process due to the rapid hydrogen production rate. However, the main drawback of it is the low hydrogen production yield due to intermediate products such as organic acids. To improve the hydrogen production yield, a co-culture system of dark and photo fermentation bacteria was applied to this research. The maximum specific growth rate of R. sphaeroides was determined to be $2.93h^{-1}$ when acetic acid was used as a carbon source. It was quite high compared to that of using a mixture of volatile fatty acids (VFAs). Acetic acid was the most attractive to the cell growth of R. sphaeroides, however, not less efficient in the hydrogen production. In the co-culture system with glucose, hydrogen could be steadily produced without any lag-phase. There were distinguishable inflection points in the accumulation of hydrogen production graph that resulted from the dynamic production of VFAs or consumption of it by the interaction between the dark and photo fermentation bacteria. Lastly, the hydrogen production rate of a repeated fed-batch run was $15.9mL-H_2/L/h$, which was achievable in the sustainable hydrogen production.

• Economic and Environmental Geology
• /
• v.53 no.5
• /
• pp.529-542
• /
• 2020

The cesium (Cs) sorption characteristics of a bead-type polysulfone carrier contained HNO₃-treated bamboo charcoal (3 - 5 mm in diameter) in water system were investigated and its Cs removal efficiency as an adsorbent from water was also identified by various laboratory experiments. From the results of batch sorption experiments, the bead-type polysulfone carrier with only 5% HNO₃-treated bamboo charcoal (P-5NBC) represented the high Cs removal efficiency of 57.8% for 1 hour sorption time. The Cs removal efficiency of P-5NBC in water after 24 hours reaction maintained > 69% at a wide range of pH and temperature conditions, attesting to its applicability under various water systems. Batch sorption experiments were repeated for P-5NBC coated with two cultivated microorganisms (Pseudomonas fluorescens and Bacillus drentensis), which were typical indigenous species inhabited in soil and groundwater. The Cs removal efficiency for two microorganisms coated polysulfone carrier (BP-5NBC) additionally increased by 19% and 18%, respectively, compared to that of only P-5NBC without microorganisms coated. The average Cs desorption rate of P-5NBC for 24 h was lower than 16%, showing the Cs was stably attached on HNO₃-treated bamboo charcoal in so much as its long-term use. The maximum Cs sorption capacity (q_m) of P-5NBC calculated from the Langmuir isotherm model study was 60.9 mg/g, which was much higher than those of other adsorbents from previous studies for 1 h sorption time. The results of continuous column experiments showed that the P-5NBC coated with microorganisms packed in the column maintained > 80% of the Cs removal efficiency during 100 pore volumes flushing. It suggested that only 14.7 g of P-5NBC (only 0.75 g of HNO₃ treated bamboo charcoal included) can successfully clean-up 7.2 L of Cs contaminated water (the initial Cs concentration: 1 mg/L; the effluent concentration: < 0.2 mg/L). The present results suggested that the Cs contaminated water can be successfully cleaned up by using a small amount of the polysulfone carrier with HNO₃-treated bamboo charcoal.