• Magazine of the Korean Society of Agricultural Engineers
• /
• 제34권1호
• /
• pp.49-56
• /
• 1992

This study was carried out to investigate the mechanical behaviour of the plate on a Winkler's foundation according to the soil-structures relative stiffness and the applicability of the conventional analysis method. For the above purpose, Winkler's constant of 4, 15, 25 and 100kg/$cm^2$/cm was considered and the plate thickness of 20, 30, 50, 100 and 150cm was adopted. Results obtained from the numerical examples are summarized as follow: 1. The effects of elastic foundation is considerable for plates with small flexural rigidity. 2. As the Winkler's constant increases, the bending moment in the plate becomes localized near the loading point. 3. The stresses evaluated by the conventional method not correct even for rigid ground such as rock. 4. If the relative stiffness of the plate is very large, for example the plate thickness is larger than 100cm, the conventional analysis method can be justified for the design purposes. 5. On assumption the flexural rigidity of the plate is infinite, the interaction of soil and plate can be ignored in design consideration. The numerical examples in this paper show that when the plate thickness is more than 100cm, the effects of elastic foundation almost disappear. In practical design, soil-plate interaction should be taken into account, because the 100cm-thickness of the plate will not be practical value in usual sites.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• 제40권4호
• /
• pp.54-59
• /
• 2003

In this paper, a cylindrical dielectric antenna with dielectric clad is designed and analyzed. Design parameters of a cylindrical dielectric resonator antenna are calculated from the wave equation of cylindrical dielectric. The variations of characteristics of the antenna are analyzed as varying the thickness and the relative permittivity of its clad. From the results, when the ratio of the outside radius of the dielectric clad to the radius of the cylindrical dielectric is 1.3 and the relative permittivity of the dielectric clad is one-third of the cylindrical dielectric resonator antenna, the relative bandwidth of the antenna is 49%, which is improved by 2.3 times than the cylindrical dielectric resonator antennas. However, the thickness and the relative permittivity of the dielectric clad have not effect on the radiation pattern, beamwidth and gain of the antenna.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제28권6호
• /
• pp.659-666
• /
• 2015

In this paper, various influence factors on the impact-echo test which is an effective method in characterizing defects such as such as the delamination in the concrete structures were studied. The side to thickness ratio(a/h), the relative position of impacting and sensing points over the delamination that have great effects on the flexural and impact-echo(thickness) modes were investigated and examined by the parametric finite element analysis. As a result, the flexural modes dominate in the case of a/h > 2 and the thickness mode was more evident when a/h < 2. With regard to the relative position of impact source and sensing point to the defect, the flexural modes dominate even when either the loading or sensing point was over the delamination defect. However, the thickness mode prevails when both the impacting and sensing points are over the solid region beyond the delamination area.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• 제34권1호
• /
• pp.41-51
• /
• 2018

In case of evaluating the bond stress of a void deck plate using a wire steel, there is no standard formula considering both the influence on the void and the type of the reinforcing bar. Therefore we proposed a model equation considered the bond characteristics of the void deck plate. A total of 46 specimens was carried out a direct pull-out test and the test variables were the presence of a void body, type of reinforcing bar, the inner cover thickness according to the location of reinforcing bars and bond region. As a result of the comparison between the steel bar and steel wire, the bond stress of the steel wire with the relative rib area of 0.071 is 4.5 ~ 28.58% lower than that of the steel bar with 0.092 and the bond stress reduction rate increases when the inner cover thickness is insufficient. In the case of the inner cover thickness of $1.7d_b$ and $2.7d_b$, the bond stress was reduced to 48.7 ~ 68.4%. In the inner cover thickness was $4.9d_b$ and $5.2d_b$, the bond stresses were equivalent to those of the solid specimens. It was confirmed that the average bond stress and strain were affected by the inner cover thickness. Therefore the predicted model for one module of the void deck plate is proposed and verified by considering the bond characteristics of the void deck plate.

• Journal of Ocean Engineering and Technology
• /
• 제16권3호
• /
• pp.40-45
• /
• 2002

In this study, the effects on hydraulic characteristics are discussed as the permeable underlayer thickness of the rubble mound structure changes. A series of hydraulic experiments were performed and wave run-up, reflection and set-up were investigated. Result indicated that wave run-down was affected by the water out from the permeable underlayer during down-rush. As the thickness increased, relative wave run-up decreased.

• Journal of Nutrition and Health
• /
• 제24권4호
• /
• pp.308-313
• /
• 1991

This study attempted to measure subcutaneous fat thickness by the use of ultrasonic wave in age and sex matched Korean subjects, and to observe correlation between fat thick-ness and physical indices. In male, fat thickness of suprailiac area showed the highest value of $9.40{\sim}9.51mm$ and then subscapular was $6.60{\sim}6.84mm$, femoral was $6.48{\sim}7.04mm$ and triceps regions was $3.48{\sim}3.69mm$. In female, femoral subcutaneous fat thickness was the higher. $11.85{\sim}12.15mm$and then suprailiac was $8.79{\sim}9.87mm$ subscapular was $6.20{\sim}6.91mm$ and triceps fat thickness was $4.80{\sim}4.93mm$. In male, fat thickness of triceps and relative body weight(RBW). body mass index(BMI), triceps or $R\ddot{o}hrer$ index were positively correlated. Correlations between suprailiac and weight, relative body weight(RBW). body mass index(BMT), $R\ddot{o}hrer$ index or subscapular were positively significant. In female. there were positive correlations between fat thickness of femoral and RBW, BMI, or $R\ddot{o}hrer$ index. And there were no positive correlations in other parts of the body.

• The Korea Journal of Herbology
• /
• 제20권4호
• /
• pp.83-94
• /
• 2005

Objectives : The present study attempted to reveal the effects of Morindae Radix extracts on the sciatic nerve neurectomized osteoporotic ddy mice model. Methods : Thickness of hind limbs and their differences, absolute and relative tibia weight and thickness, bone failure load, bone mineral density (BMD), histomorphometrical index, serum osteocalcin level, tibia calcium and phosphorus contents were monitored. Results : In sciatic neurectomized mice, thickness of hind limb, absolute and relative weights, thickness, failure loads, BMD of tibia, trabecular bone volume (TBV), thickness of trabecular bone and cortical bone thickness, length were significantly decreased. However, these changes of those dose-dependently reduced in MR extract-dosing group. Conclusions : it is considered that MR extracts have some favorable effect to prevent, the osteoporosis induced by sciatic neurectomy. However, the exact mechanism and the possibility of MR extract were remains unknown. In addition, the potential toxicity of these MR extracts were also unknown. So the further studies were needed about toxicological and pharmacological aspects.

• The Journal of Korean Society for Radiation Therapy
• /
• 제31권1호
• /
• pp.57-65
• /
• 2019

Purpose: The purpose is to clarify the effect of additional scattering ratio on the edge of the block according to the increasing block thickness with low melting point lead alloy and pure lead in electron beam therapy. Methods and materials: $10{\times}10cm^2$ Shielding blocks made of low melting point lead alloy and pure lead were fabricated to shield mold frame half of applicator. Block thickness was 3, 5, 10, 15, 20 (mm) for each material. The common irradiation conditions were set at 6 MeV energy, 300 MU / Min dose rate, gantry angle of $0^{\circ}$, and dose of 100 MU. The relative scattering ratio with increasing block thickness was measured with a parallel plate type ion chamber(Exradin P11) and phantom(RW3) by varying the position of the shielding block(cone and on the phantom), the position of the measuring point(surface ans depth of $D_{max}$), and the block material(lead alloy and pure lead). Results : When (depth of measurement / block position / block material) was (surface / applicator / pure lead), the relative value(scattering ratio) was 15.33 nC(+0.33 %), 15.28 nC(0 %), 15.08 nC(-1.31 %), 15.05 nC(-1.51 %), 15.07 nC(-1.37 %) as the block thickness increased in order of 3, 5, 10, 15, 20 (mm) respectively. When it was (surface / applicator / alloy lead), the relative value(scattering ratio) was 15.19 nC(-0.59 %), 15.25 nC(-0.20 %), 15.15 nC(-0.85 %), 14.96 nC(-2.09 %), 15.15 nC(-0.85 %) respectively. When it was (surface / phantom / pure lead), the relative value(scattering ratio) was 15.62 nC(+2.23 %), 15.59 nC(+2.03 %), 15.53 nC(+1.67 %), 15.48 nC(+1.31 %), 15.34 nC(+0.39 %) respectively. When it was (surface / phantom / alloy lead), the relative value(scattering ratio) was 15.56 nC(+1.83 %), 15.55 nC(+1.77 %), 15.51 nC(+1.51 %), 15.42 nC(+0.92 %), 15.39 nC(+0.72 %) respectively. When it was (depth of $D_{max}$ / applicator / pure lead), the relative value(scattering ratio) was 16.70 nC(-10.87 %), 16.84 nC(-10.12 %), 16.72 nC(-10.78 %), 16.88 nC(-9.93 %), 16.90 nC(-9.82 %) respectively. When it was (depth of $D_{max}$ / applicator / alloy lead), the relative value(scattering ratio) was 16.83 nC(-10.19 %), 17.12 nC(-8.64 %), 16.89 nC(-9.87 %), 16.77 nC(-10.51 %), 16.52 nC(-11.85 %) respectively. When it was (depth of $D_{max}$ / phantom / pure lead), the relative value(scattering ratio) was 17.41 nC(-7.10 %), 17.45 nC(-6.88 %), 17.34 nC(-7.47 %), 17.42 nC(-7.04 %), 17.25 nC(-7.95 %) respectively. When it was (depth of $D_{max}$ / phantom / alloy lead), the relative value(scattering ratio) was 17.45 nC(-6.88 %), 17.44 nC(-6.94 %), 17.47 nC(-6.78 %), 17.43 nC(-6.99 %), 17.35 nC(-7.42 %) respectively. Conclusions: When performing electron therapy using a shielding block, the block position should be inserted applicator rather than the patient's body surface. The block thickness should be made to the minimum appropriate shielding thickness of each corresponding using energy. Also it is useful that the treatment should be performed considering the influence of scattering dose varying with distance from the edge of block.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.323-326
• /
• 2003

This paper presents a new algorithm that can refine hexahedral elements while maintaining the appropriate connectivity. In the algorithm, at first the regions of mesh to be refined are defined and, then, the zero-thickness element layers inserted into the interfaces between the regions. All the meshes in the regions, in which the zero-thickness layers are inserted, are to be regularized in order to improve the shape of the slender elements on the interfaces. This algorithm is applied to the analysis of plastic deformation process. The results show that the refined mesh gives smaller relative errors than the original mesh.

• Transactions of Materials Processing
• /
• 제14권3호
• /
• pp.277-281
• /
• 2005

LTCC(Low temperature co-fired ceramic) is being recognized as a significant packaging material of electrical devices for the advantages such as relatively low temperature being needed for process, low conductor resistance and high printing resolution. In the process of LTCC electrical devices, the punched via-hole quality is one of the most important factors on the performance of the device. However, its mechanism is very complicated and optimization of the process seems difficult. In this paper, to clarify the process, via-hole punching experiments were carried out and the punched holes were examined in terms of their burr formation. The effects of thickness of PET sheet, ceramic sheet and punch-to- die clearance on via-hole quality were also discussed. Optimum process conditions are proposed and a factor $\kappa$ is introduced to express effect of the process variables.