• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.47 no.6
• /
• pp.1014-1025
• /
• 2014

We measured the concentrations of various geochemical parameters [grain size, ignition loss (IL), chemical oxygen demand (COD), acid volatile sulfide (AVS), and trace metals (Fe, Cu, Cd, Pb, Cr, Mn, As, Zn, and Hg)] in the surface sediments of two intertidal oyster Crassostrea gigas farming areas (Iwon and Mongsan tidal flats) on the Taean Peninsula, Korea, to evaluate the pollution level of organic matter and trace metals in sediment. The intertidal sediments in the study region comprise mostly sand with a mean grain size of 2.5-3.5 Ø. The concentrations of IL, COD, AVS, and trace metals in the sediment of two study regions were either similar or lower in oyster farming areas relative to non-farming areas, apparently due to biological uptake or physical and biological sediment reworking. Based on the results for the pollution evaluation of organic matter and trace metals derived from sediment quality guidelines, enrichment factor, and geoaccumulation index, our results suggest that the sediment in these two intertidal oyster farming regions is not polluted by organic matter and trace metals.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1183-1189
• /
• 2015

This study focuses on the design of the tapered joints of a wind power turbine. The main variables of the tapered joint are the transmitted torque, shaft diameter, contact area of the tapered ring, and tightening torque of the bolts, which applies a compressive pressure from the hub to the shaft. The stress distribution of the taper fit was calculated under axisymmetric plane strain conditions because of the small taper angle. The axial displacement of the clamp can be calculated from the radial elastic deformation and the taper angle. The stress field of each ring is obtained from the cylinder stress equation. To verify the accuracy of the calculation, finite element (FE) analysis was performed, and the results of the calculation and FE analysis were compared. The hoop stress of the tapered surface showed a discrepancy of approximately 10, but the trends of the stress distributions of each component and the relative movement obtained by FE analysis were in good agreement with the analytical calculation results.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.715-723
• /
• 2006

Perovskite oxide materials are very important for the electronics industry, because they exhibit promising properties. With an interest in the obvious applications, significant effort has been invested in the growth of highly crystalline epitaxial perovskite oxide thin films in our laboratory. And the desired structure of films was formed to achieve excellent properties. $Y_1Ba_2Cu_3O_{7-x}$ (YBCO) superconducting thin films were simultaneously deposited on both sides of 3 inch wafer by inverted cylindrical sputtering. Values of microwave surface resistance R$_2$ (75 K, 145 GHz, 0 T) smaller than 100 m$\Omega$ were reached over the whole area of YBCO thin films by pre-seeded a self-template layer. For implementation of voltage tunable high-quality varactor, A tri-layer structured SrTiO$_3$ (STO) thin films with different tetragonal distortion degree was prepared in order to simultaneously achieve a large relative capacitance change and a small dielectric loss. Highly a-axis textured $Ba_{0.65}Sr_{0.35}TiO_3$ (BST65/35) thin films was grown on Pt/Ti/SiO$_2$/Si substrate for monolithic bolometers by introducing $Ba_{0.65}Sr_{0.35}RuO_3$ (BSR65/35) thin films as buffer layer. With the buffer layer, the leakage current density of BST65/35 thin films were greatly reduced, and the pyroelectric coefficient of $7.6\times10_{-7}$ C $cm^{-2}$ $K^{-1}$ was achieved at 6 V/$\mu$m bias and room temperature.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 1998.10a
• /
• pp.313-335
• /
• 1998

If the atmospheric concentrations of greenhouse gases double, the annual temperature increase in mean surface temperature relative to 1990 will be about 2.0 to $2.5^{\circ}C$ and the annual precipitation increase about $15{\%}$ by 2100 in Korea. When the temperature rises $2^{\circ}C$, the annual temperature will be $13^{\circ}C,\;15^{\circ}C,\;and\;16^{\circ}C$ in Western Central, Yeongnam Basin, and Southern Coastal respectively. Consequently the crop period could be prolonged $10{\~}29$ days. In the case of gradual global warming, annual crops could be adapted to the changed environment by breeding, and the perennial crops should be shifted to ether area. If global warming happens suddenly over the threshold of atmospheric greenhouse gases concentration, then we shall have disturbance of ecosystem. When $2^{\circ}C$ higher than present, the optimum flowering date of rice plant delayed about 10 days, so it may not possible to adopt the fate with present japonica rices, therefore, the recommended characteristics of rice varieties are longer basic vegetative period, more late maturing and higher ripening temperature. Barley and wheat crops could be shifted to northern coastal areas and apple production areas should be shifted to those areas under $13.5^{\circ}C$ in annual mean temperature at global warming. Ideotypes of crops under climate changes should have such ecological characteristics that are indispensable to accomplish the sustainable agriculture under increased $CO_{2}$ and temperature condition as the diversification of genetic resources from yield-oriented to biomass-oriented characteristics with the higher potentials of $CO_{2}$ absorption and Primary production. In addition, a heat-tolerance, a pest resistance, an environmental adaptability and a production stability should be also incorporated collectively into our integrated agroecosystem.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.194-194
• /
• 2016

Gansu, located in the northwestern region, is a typical agricultural province of arid, semiarid in China. The shortage of water resources is the biggest obstacle of Gansu Province's development, and the dry farming water-saving is the eternal theme of Gansu agricultural sustainable development. In recent years, intensify reform in Gansu, has walked out a successful way in the agricultural water-saving. Using the integrated river basin governance as opportunity, the total water-using quantity was regarded as rigidity to retrain, distributed to counties (districts), irrigated areas, towns, associations, groups step by step. Agricultural water price was substantially increased, with the surface water price from about $0.1RMB/m^3$ to more than $0.2 RMB/m^3$, and the ground water from zero to more than $0.1RMB/m^3$. Simultaneously, the difference water prices and over-quota water progression price markup were carried out. The transaction of water rights was encouraged to impel the peasant to establish the consciousness of saving-water. The regulatory documents were formulated to standardize the scope, condition, mode, program etc. of agriculture water-rights transaction, to guarantees the transaction of water rights is carries out in order. The pattern of farming was optimized and adjusted, reducing the high water-consumption crop, increasing economic crops with high benefit and low water-consumption, developing industrialized agricultures such as green house. The relative engineering and measuring facility were comprehensively improved, with the anti-seepage of canal system and the enforcement of dynamo-electric well, developing high-efficient water-saving irrigation and overall metering facilities. The water fine-grained management has realized, and obvious water-saving effect has obtained: water-using rate in the irrigation area by river water has brought up to 0.57 from 0.52, and by well water up to 0.84 from 0.76. Although the water price has increased, the proportion that the water rate expenditure accounted for the cost lasts decline, and the farmers' income has gone up. The peasants express, the used water is few, and it is few to till land, but the income is many, and life is better.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.743-750
• /
• 2008

Asymmetric tip clearance in an axial compressor induces pressure and velocity redistributions along the circumferential direction in an axial compressor. This paper presents the mechanism of the flow redistribution due to the asymmetric tip clearance with a simple numerical modeling. The flow field of a rotor of an axial compressor is predicted when an asymmetric tip clearance occurs along the circumferential direction. The modeling results are supported by CFD results not only to validate the present modeling but also to investigate more detailed flow fields. Asymmetric tip clearance makes local flow area and resultant axial velocity vary along the circumferential direction. This flow redistribution 'seed' results in a different flow patterns according to the flow coefficient. Flow field redistribution patterns are largely dependent on the local tip clearance performance at low flow coefficients. However, the contribution of the main flow region becomes dominant while the tip clearance effect becomes weak as the flow coefficient increases. The flow field redistribution pattern becomes noticeably strong if a blockage effect is involved when the flow coefficient increases. The relative flow angle at the small clearance region decreases which result in a negative incidence angle at the high flow coefficient. It causes a recirculation region at the blade pressure surface which results in the flow blockage. It promotes the strength of the flow field redistribution at the rotor outlet. These flow pattern changes have an effect on the blade loading perturbations. The integration of blade loading perturbation from control volume analysis of the circumferential momentum leads to well-known Alford's force. Alford's force is always negative when the flow blockage effects are excluded. However when the flow blockage effect is incorporated into the modeling, main flow effects on the flow redistribution is also reflected on the Alford's force at the high flow coefficient. Alford's force steeply increases as the flow coefficient increases, because of the tip leakage suppression and strong flow redistribution. The predicted results are well agreed to CFD results by Kang and Kang(2006).

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.2
• /
• pp.33-39
• /
• 2010

The moisture absorption properties such as diffusion coefficient and moisture content ratio of liquid type epoxy resin systems with the filler were investigated. Bisphenol A type and Bisphenol F type epoxy resin, Kayahard MCD as hardener and 2-methylimidazole as catalyst were used in these epoxy resin systems. The nano-sized spherical type fused silica as filler were used in order to study the moisture absorption properties of these liquid type epoxy encapsulant according to the change of filler size. The temperature of glass transition (Tg) of these epoxy resin systems was measured using Dynamic Scanning Calorimeter (DSC), and the moisture absorption properties of these epoxy resin systems according to the change of time were observed at $85^{\circ}C$ and 85% relative humidity condition using a thermo-hygrostat. The diffusion coefficients in these systems were calculated in terms of modified Crank equation based on Ficks' law. An increase of Tg and diffusion coefficient with filler size in these systems can be observed, which are attributed to the increase of free volume with Tg. The change of maximum moisture absorption ratio according to the filler size and filler content cannot be observed; however, the diffusion coefficients of these systems decreased with filler content. The diffusion via free volume is dominant in the epoxy resin systems with low nano-sized filler content; however, the diffusion with the interaction of absorption according the increase of the filler surface area is dominant in the liquid type epoxy encapsulant with high nano-sized filler content.

• Journal of Korean Society on Water Environment
• /
• v.37 no.1
• /
• pp.10-19
• /
• 2021

In the flotation process to remove microplastic (MP) particles, the attachment and separation efficiency is determined by the basic physicochemical characteristics of MP particles as well as bubbles. To evaluate the flotation characteristics of MP particles, we carried out a series of simulations using the population balance (PB) model. The initial attachment coefficient (αo) of MP particles was in the range of 0.2-0.275, and it was slightly lower than that of typical particles, such as clay, debris and algae particles, which exist in water bodies, αo, 0.3-0.4. The relative bubble number (RBN) attached to the surface of the typical number of bubbles was 0.30 and 0.32 for MP 30 ㎛ and MP 58 ㎛, respectively. In comparison, the RBN of larger MP particles (138 ㎛) was as high as 0.53. Furthermore, smaller microbubbles were required to separate properly or additional treatment needed to be applied to enhance collision and attachment efficiency since the flotation of MP particles was found to be difficult to treat as high-rate. As a result of comparing the removal rate (experimental value) of MP particles obtained from the batch-type flotation apparatus and the flotation removal rate (predicted value) of MP obtained through the PB model, the final particles by the particle size of MP overall except for the initial separation time area. With respect to the removal efficiency, the observed and predicted values were similar, and it was confirmed that the floating separation characteristics and evaluation of the MP particles through the PB model could be possible.

• Ecology and Resilient Infrastructure
• /
• v.9 no.1
• /
• pp.59-67
• /
• 2022

The purpose of this study is to provide essential data necessary to assess ecological flow requirements by understanding habitat conditions for fish species through monitoring an ecological environment in the Korea stream (Dal Stream) and building related database. On-site surveys were conducted for identifying ecological and habitat conditions at the four monitoring sites. Fish sampling was carried out at the selected four sites (St.) during the period ranging from September, 2008 to September, 2009. At the four sampling sites, we measured water surface elevation, depth and velocity at the cross-sections. Optimal Ecological Flowrates (OEFs) were estimated using the Habitat Suitability Index (HSI) established for four fish species Zacco koreanus (St.1), Pungtungia herzi (St.2), Coreoleuciscus splendidus (St.3), and Zacco platypus (St.4) selected as icon species using the Physical HABitat SIMulation system (PHABSIM). Eighteen species (56.3%) including Odontobutis interrupta, Coreoperca herzi and C. splendidus were found endemic out of the 32 species in eight families sampled during this study period. The endangered species was collected Acheilognathus signifier, Pseudopungtungia tenuicorpa and Gobiobotia macrocephala, and this relative abundance was 9.4%. The most frequently found one was Z. platypus (31.3%) followed by C. splendidus (17.6%) and Z. koreanus (15.7%). The estimated IBI values ranged from 27.3 to 34.3 with average being 30.3 out of 50, rendering the site ecologically poor to fair health conditions. For C. splendidus (St.3), the dominant fish species in the stream, the favored habitat conditions were estimated to be 0.3-0.5 m for water depth, 0.4-0.7 m/s for flow velocity and sand-cobbles for substrate size, respectively. An OEFs of 8.5 m³/s was recommended for the representative fish species at the St.3.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.5
• /
• pp.547-558
• /
• 2023

This research delves into the fabrication of an ultra-high-strength concrete, enriched with oxidized graphene nanoplatelet(GO) and hollow glass powder(HGP), notably eschewing the conventional inclusion of silica fume(SF). The primary objective was to scrutinize the autogenous shrinkage characteristics of this innovative formulation. It was discerned that the NewMix specimen, which incorporated the cGO(sourced from Company C) and HGP, and intentionally bypassed SF, showcased a commendable 13% reduction in autogenous shrinkage relative to the benchmark(Ref) specimenthat incorporated SF. Moreover, the proclivity for crack formation owing to autogenous shrinkage in the NewMix was observed to manifested by NewMix at the juncture of cracking emerged as the apex value. Attributed to the expansive specific surface area and exemplary dispersibility of cGO, it was postulated that the concrete's pore structure benefitted from enhanced infill, leading to a reduction in autogenous shrinkage. Additionally, the cGO integration fortified the concrete's resistance to crack initiation. Consequently, such an enhancement is posied to be pivotal in mitigating crack propagation resulting from autogenous shrinkage in ultra-high-strength concrete.