• Journal of the Korea Safety Management & Science
• /
• v.4 no.4
• /
• pp.137-146
• /
• 2002

In order to investigate the effect of irradiation by $^{60}Co-\gamma$rays as well as the e thermal treatment on the dielectric deterioration in ethylene propylene rubber, insulating material for electric cables used in atomic power plants, charging discharging current, residual built- up voltage and dielectric properties are measu discussed in this study. Variance in the characteristic of relative dielectric constant as a function of tem was observed in relatively high dose of irradiation. Since glass transition tem appeared at tens of degree Celsius below zero, the characteristic is attributed orientation polarization. Dielectric loss is generally increased, with increasing d irradiation in the characteristic of dielectric loss as a function of temperature, No d loss by thermal treatment was observed. Dielectric resistance decreases with increa of irradiation in the characteristic of charging current as a function of temperature be considered that dielectric resistance seems to be recovered by thermal treatm characteristic of discharging current as a function of time in the specimen less ir become similar to that of the unirradiated, when thermal treated. A peak is shown residual built- up voltage as a function of time, and the corresponding time of the shorten as increasing dose of irradiation. It is also observed that the corresponding the peak is lengthened by thermal treatment.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.7
• /
• pp.287-291
• /
• 2002

We fabricated the crosslinked films using p-hexadecoxyphenol (p-HP), which is amphiphilic and can form polyion complexes with formaldehyde at the air-water interface. The behavior of polyion complexation at the air-water interface and the surface structure of LB films was investigated by Brewster angle microscope(BAM) and scanning Maxwell-stress microscope (SMM), respectively. Also, the electrical properties for crosslinking in phenol-formaldehyde LB films were investigated by measuring conductivity and dielectric constant. The conductivities of p-HP LB films are as follows: heat-treatment of 1% formaldehyde subphase(3.76$\times$10$^{-15}$ ~4.76$\times$10$^{-1}$5[S/cm])$\times$10$^{-14}$ ~1.74$\times$10$^{-14}$ [S/cm]). Also, relative dielectric constants of p-HP LB films were reduced from 6.76~7.84 (pure water) to 2.97~3.25 (heat-treatment of 1% formaldehyde subphase))

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.583-590
• /
• 1997

The effects of Mn2O3 and Y2O3 additives on the microstructure and dielectric properties of Sr(Zr, Ti)O3 have been investigated. Powders with Sr(Zr1-xTix)O3(0$\leq$x$\leq$0.1) composition were prepared by the conventional solid state processing from commercial TiO2 and precipitation-processed ZrO2. The powders containing sintering additives of Mn2O3 and Y2O3 were compacted and then sintered at 1,55$0^{\circ}C$ for 4 h to get>97% relative density. Mn2O3 suppressed the grain growth and Y2O3 enhanced the density of sintered body. The oxidation state of Mn ions were determined by a chemical wet method and EPR spectroscopy. Mn ions were present as Mn2+ and Mn4+ in SrZrO3, while as Mn3+ and Mn4+ in Ti-substituted Sr(Zr, Ti)O3. With the substitution of Ti, the lattice parameters of SrZrO3 decreased and its dielectric constant increased with remarkable decrease in Q value. The dielectric constant of Sr(Zr, Ti)O3 was in the range of 30 to 40, Q values 1,200~5,400 at 6 GHz and temperature coefficient of resonant frequency -67~100 ppm/K.

• Korean Journal of Remote Sensing
• /
• v.10 no.2
• /
• pp.17-35
• /
• 1994

A semi-empirical model for microwave polarimetric radar backscattering from bare soil surfaces was developed using polarmetric radar measurements and the knowledge based on the theoretical and numerical solutions. The microwave polarimetric backscatter measurements were conducted for bare soil surfaces under a variety of roughness and moisture conditions at L-, C-, and X-band frequencies at incidence angles ranging from 10` to 70`. Since the accrate target parameters as well as the radar parameters are necessary for radar scattering modeling, a complete and accurate set of ground truth data were also collected using a laser profile meter and dielectric probes for each surface condition, from which accurate measurements were made of the rms height, correlation length, and dielectric constant. At first, the angular and spectral dependencies of the measured radar backscatter for a wide range of roughnesses and moisture conditions are examined. Then, the measured scattering behavior was tested using theoretical and numerical solutions. Based on the experimental observations and the theoretical and numerical solutions, a semi-empirical model was developed for backscattering coeffients in terms of the surface roughness parameters and the relative dielectric constant of the soil surface. The model was found to yield very good agreement with the backscattering measurements of this study as well as with independent measurements.

• The Journal of Engineering Geology
• /
• v.13 no.4
• /
• pp.405-418
• /
• 2003

Measurements of volumetric water content and saturation of porous media are very important factors in understanding the physical characteristics of soil, groundwater recharge by rainfall, pollutant movement, and slope failure. To measure such physical parameters, a permittivity method using electromagnetic wave is applied and use is made of the special permittivity response of understand to water and ethanol. In particular, the estimation is required because permittivity is influenced by the nature of the underground environment. In this study, we carried out experiments on the relative dependency of soil density, temperature and salinity of standard sand and granitic weathered soil using FDR-V system (Frequency domain reflectometry with vector network analyzer) within a frequency range of 1 - 18 GHz. The results of the study showed that the dielectric constants of standard sand and granitic weathered soil increased with increased volumetric water content of soil. However, the dependency of soil density was found to be a little low. Changes of dielectric constant with temperature appeared definitely in the real part of 1 GHz. That is, the dielectric constant of real part at 1 GHz of water and standard sand increased with the rise of temperature. However, ethanol showed decreased tendency. The study also showed that dielectric constant increased with increase in salinity at imaginary part of 1 GHz. It could be concluded from this study FDR-V system can adequately measure the physical properties of soil and the degree of salinity concentration of porous media within 1 GHz frequency range using dielectric constant.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.4
• /
• pp.46-54
• /
• 2002

A dielectric pellets bedded parallel plates with a membrane centered have been proposed as an ion separation and collection system in water. and effects of the relative dielectric constant and the applied square wave pulse voltage on the characteristics of ion separation and collection in tap water and NaCl dissolved tap water have been investigated. As a result, electrolyzed water of pH 3.1 and 10.6 were obtained with only tap water at the pulse current of 1.0[A] and flow rate of 0.5[LPM]. And the higher ionized water of pH 2.8 and pH 11.7 ware obtained in 0.1[%wt] NaCl dissolved water. When the dielectric pellets of BaTiO$_3$ having the highest dielectric constant were bedded in the ion separation and collection cell, the ionized water of pH 2.7 and pH 11.7 were obtained with only tap water. And the ionized water of pH 2.4 and pH 12.0 were obtained in 0.1[wt%] NaCl dissolved tap water with the dielectrics pellets bedded ones.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.819-829
• /
• 1997

The microwave dielectric materials of the BaO-Nd$_2$O$_3$-TiO$_2$and BaO-(Sm, Nd)$_2$O$_3$-TiO$_2$system were synthesized by conventional ceramic processing and sintered 1220 to 140$0^{\circ}C$ for 2 hours respectively. Their crystallization and dielectric properties were examined. In the BaO-Nd$_2$O$_3$-TiO$_2$ and BaO-(Sm, Nd)$_2$O$_3$-TiO$_2$system. Nd$_2$Ti$_2$O$_{7}$ and (Sm, Nd)$_2$Ti$_2$O$_{7}$ were observed as a second phase respectively. The maximum relative dielectric constant were 79,99 for the BaO-Nd$_2$O$_3$-TiO$_2$system and 105.07 for the BaO-(Sm,Nd)$_2$O$_3$-TiO$_2$system and their Q-value were over 2000 at 3GHz.GHz.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.11
• /
• pp.1174-1177
• /
• 2004

The dielectric and piezoelectric properties of silver added 0.96 Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_3$-0.04 Pb(Mn,W,Sb,Nb)$_3$ ceramics were examined. By varying the contents of silver(0.0, 0.4, 1.0 mol%), the effect of silver addition on PZT-PMWSN ceramics was investigated at various sintering temperature(900, 1000, 1100 $^{\circ}C$). As increasing silver contents, the relative dielectric constant was increased and sinterability was enhanced. At the specimen with 0.4 mol% Ag and sintered at 1000 $^{\circ}C$, electromechanical coupling factor( $k_{p}$), mechanical quality factor( $Q_{m}$), dielectric constant($\varepsilon$$_{r}$) and dielectric loss were 0.502, 811, 991, 0.006, respectively. The results showed that the PZT-PMWSN/Ag composites have enhanced piezoelectic and dielectric properties and sintering temperature was lowered.red.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.2
• /
• pp.47-52
• /
• 2019

In this paper, TE(transverse electric) scattering problems by a conductive strip grating between a double dielectric layer are analyzed by applying the FGMM(Fourier-Galerkin moment method) known as a numerical method of electromagnetic fileld. The boundary conditions are applied to obtain the unknown field coefficients, and the conductive boundary condition is applied to analysis of the conductive strip. The numerical results for the normalized reflected and transmitted power are analyzed by according as the width and spacing of conductive strip, the relative permittivity and thickness of the double dielectric layers, and incident angles. Generally, as the value of the dielectric constant increases, the reflected power increases and the transmitted power decreases, respectively. As the dielectric constant increases, the current density induced in the strip increases as it goes to both strip ends. The numerical results for the presented structure of this paper are shown in good agreement compared to those of the existing papers.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.65-74
• /
• 1993

A miniature size electrostatic induction motor has been fabricated and studied with emphasis on the role of the surface resistivity, the relative dielectric constant and the charge relaxation time constant of the rotor surface materials and the rotor liner materials, which, however, control the surface charge induction and relaxation on the rotor material surface and the field intensity between the rotor and the stator of the motor. It is found that the surface resistivity and/or the relative dielectric constant, and the charge relaxation time constant of the rotor surface material enfluenced significantly to motor speed controlled by the surface charge induction and relaxation on the rotor surface depending on the applied voltage and/or frequency changing. The resistivity of the rotor liner material is also found to be effected to the motor speed greatly by control of the field intensity between the rotor and the stator and of the surface charge distribution of the induced charge on the rotor. As a result, a maximum no load rotor speed of the motor tested was about 5500 rpm at the applied voltage of 4.5 kV and the frequency of 220 Hz for the case of the rotor surface material of $BaTiO_{3}$ 80% in the resin binder layered on the copper-foil rotor liner material.