• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.11a
• /
• pp.71-74
• /
• 2005

The viscosity of high-flowability paste is very high compared to normal concrete for the low water-binder ratio(W/B). Therefore, high-flowability concrete is positively necessary to high-range water reducing agent. High-Flowability paste can make much higher fluidity with no occurrence of segregation, by its higher viscosity and lower yield value than normal concrete. The flowability of high-flowability paste must be evaluated not only by convention consistency test such as slump test but also by the base of the rheological properties of the fresh concrete. The purpose of this study is to analyze the fluidity of high-flowability paste according to the addition ratio of the Melamine Sulphonate high-range water reducing agent.; high-flowability paste is considered as Bingham plastic fluid with the rheology parameters of the plaste viscosity and yield value.

• Journal of the Korea Concrete Institute
• /
• v.11 no.4
• /
• pp.95-105
• /
• 1999

When superplasticizer is added to manufacture flowing concrete, the base concrete usually needs the adjustment to assure the sufficient fines contained to obtain flowable consistency without excessive bleeding or segregation. However, this may not only increase the cost, but also cause inconvenience in producing the base concrete. In this paper, the experiments are performed on normal base concrete to achieve a segregation-reducing flowing concrete by adding superplasticizer mixed with viscosity agents and AE admixtures. Three kinds of superplasticizer and two kinds of viscosity agent are selected. According to the results, with regard to the performance and cost of the admixtures, melamine type superplasticizer combined with the PEO viscosity agent and AE admixtures at the ratio 1:0.28:0.001 can acquire good quality and reduce the cost in producing the flowing concrete. With proper addition of combined superplasticizer, even though water to cement ratios of the base concrete are different, the segregation-reducing flowing concrete could be also achieved without reproportioning of the base concrete. However, it would be more desirable if the superplasticizer could be adjusted, before it is put into the practical use in order not to cause some other problems, such as rapid rate of slump loss and retarding of setting time.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.8
• /
• pp.720-724
• /
• 1996

Catecholalane (1,3,2-Benzodioxaluminole, CA) prepared from catechol and aluminum hydride in tetrahydrofuran (THF) is found to be a selective reducing agent. The systematic study in order to characterize the reducing properties of the reagent under practical conditions (THF, 0 or 25 ℃, the quantitative amount of reagent to compound) has been done. The reagent reduces aldehydes, ketones, esters and acid chlorides to the corresponding alcohols, and primary amides to the corresponding amines. Especially noteworthy is that the reagent can convert both aromatic and aliphatic nitriles to the corresponding aldehydes in very high yields.

• Journal of the Korea Institute of Building Construction
• /
• v.4 no.2
• /
• pp.129-136
• /
• 2004

High fluidity concrete(HFC) requires high dosage of superplasticizer to acquire sufficient fluidity, and high contents of fine powder and viscosity enhancing admixtures to resist segregation. The use of high amount of admixtures to make HFC at batcher plant in ready mixed concrete company is one of the reasons to raise the manufacturing cost of HFC. For this reason, new type of manufacturing method of HFC are described using both flowing concrete method and segregation reducing superplasticizer(SRS) in order to gain economical profit and offer the convenience for quality control.. As dosage of melamine based superplasticizer increases, it shows that fluidity and bleeding increase, while air contents and ratio of segregation resistance decrease. It also shows that addition of viscosity agent into superplasticizer reduce bleeding and improve segregation resistance of concrete. Dosage of AE agent into superplasticizer containing viscosity agent recovers loss of air contents during flowing procedure. Combination of proper contents of superplasticizer, viscosity agent and AE agent make possible to develope segregation reducing type superplasticizer. Compressive strength of high fluidity concrete applying flowing method with it is higher than that of base concrete. No differences of compressive strength between compacting methods are found. For the estimation of construction cost of high fluidity concreting using segregation reducing type superplasicizer, under same strength levels, although material cost of high fluidity concrete is somewhat higher than that of plain concrete due to segregation reducing type superplasticizer cost, labor cost and equipment cost of high fluidity concrete is cheaper than that of plain concrete. However, based on the strength differences, high fluidity concrete shows lower material cost, labor cost and equipment cost than that of plain concrete due to decreasing in size of member and re-bar caused by high strength development of concrete.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.1
• /
• pp.51-60
• /
• 2006

This study was conducted to investigate experimentally the drying shrinkage and the strength properties of redispersible SBR and PAE powder-modified mortars. Polymer-cement ratio, content of shrinkage-reducing agent and antifoamer content were manipulated as the experimental variables. The peculiarity of this study is to obtain a high early-age strength by using the portland cement and alumina cement with the ratio of 8 : 2. Until 7 days of age, the drying shrinkage remarkably increased up to $1\~2\times10^{-4}$, while it tended to decrease as the ratio of polymer to cement ratio and the content of shrinkage-reducing agent increased. Polymer-cement ratio was effective in improving the flexural, tensile and adhesive strengths: As the ratio increased, the strengths correspondingly increased. The flexural strength was in the range of $7\~11$ MPa, the tensile strength was $3.5\~5$ MPa and the adhesive strength was $1.2\~3.9$ MPa. On the other hand, the compressive strength tended to decrease as the polymer-cement ratio increased, and it was in the range of $23\~39$ MPa. All strengths, flexural, tensile, adhesive and compressive strengths, decreased as the content of powder shrinkage-reducing agent increased. It turned out that the polymer-cement ratio influenced more on the behavior of drying shrinkage and the properties of strength than the powder shrinkage-reducing agent did.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.1
• /
• pp.181-188
• /
• 2005

Generally, high performance concrete has characteristics such as low water-cementitous material ratio, lots of unit binder powder, thus the drying shrinkage and autogenous shrinkage are tend to be increased. The purpose of this study is to investigate the effect of the glyclos based shrinkage reducing agent on the drying shrinkage and autogenous shrinkage of high performance concrete with 30% of water-cemetitious material ratio as a study to develop the technology to reduce the concrete shrinkage. Test results show that the drying and autogenous shrinkage of high performance concrete are reduced by about 20~35% at the mixing ratio of shrinkage reducing agent of 0.5%, and 1.0%, compared with plain concrete. Therefore, it analyze that the using of shrinkage reducing agent is effective to reduce the drying shrinkage and autogenous shrinkage of high performance concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.23-26
• /
• 1999

The properties of concrete can be affected by high range water reducing agent and cement. The data for compatibility and effect of fluidity is reported already according to the mixing proportion of kinds of cements and high range water reducing agents. Moreover, the international market of construction has been opened, the international standard of capability has been promoted and the international exchange of construction materials has been brisked. This study investigated fluidity properties of mortar due to kinds of cements and high range water reducing agents which are producted in different nations. Also studied were the compatibility effect of cements and high range water reducing agents.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.275-282
• /
• 2002

High fluidity concrete needs high dosage of superplasticizer to acquire sufficient fluidity and high contents of fine powder and viscosity agents to prevent segregation. But it requires high manufacturing cost and has difficult in quality control. Therefore, in this paper, determination of optimal mixture proportion of segregation type superplasticizer for high fluidity concrete and manufacturing high fluidity concrete by applying developed segregation reducing type superplasticizer are discussed using flowing concrete method. According to test results, as dosage of superplasticizer increases, it shows that fluidity and bleeding increase, while air contents and ratio of segregation resistance decrease. It also shows that adding viscosity agent into it reduce bleeding and improve segregation resistance. Dosage of AE agent into it containing viscosity agent recovers loss of air contents during flowing procedure. Combination of proper contents of superplasticizer, viscosity agent and AE agent make possible to develope segregation reducing type superplasticizer Compressive strength of high fluidity concrete applying flowing method with it is higher than that of base concrete. No differences of compressive strength between compacting methods are found.

• The Research Journal of the Costume Culture
• /
• v.24 no.6
• /
• pp.777-787
• /
• 2016

This study was carried out in order to provide useful data for planning fabrics of summer eco-friendly fashion products. The fabrics used in this study were four cellulose fibers: cotton, cotton/mulberry blended, flax, and flax/lyocell blended. Dyeing with natural indigo was carried out under three different reducing conditions (i.e., general, eclectic, and eco-friendly) that have different reducing agent and pH levels, and hydrosulfite and glucose were used as a reducing agent. The dye uptake (K/S value) of fabrics dyed with natural indigo by a reducing condition was the highest at 660nm. Regardless of the fabrics, dye uptake was the highest under the general reducing condition and the lowest under the eco-friendly reducing condition. Under different reducing conditions, the dye uptake of natural indigo fabrics with the maximum absorption wavelength indicated a difference. The colorfastness of cellulose fabrics that were dyed with natural indigo had a rate of 4 to 5 except for rubbing fastness, which indicated good colorfastness. Additionally, natural indigo-dyed cotton and flax fabrics had good antibiosis. When the color characteristics of fabrics dyed with natural indigo were measured, all of the three reducing conditions created purple blue (PB) colors, and the color characteristics of dyed fabrics by reducing condition and fabric showed significant differences.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10a
• /
• pp.362-367
• /
• 1998

The purpose of this study is to examine the influences of polystyrene content and St/UP on the setting shrinkage and strengths of polymer mortar with waste expanded polystyrene resin as a shrinkage-reducing agent, and to recommend the optimum binder formulations for product of low-shrinkage polymer mortar. In this paper, polymer mortar is prepared with waste expanded polystyrene content and St/UP, and tested for setting shrinkage, flexural and compressive strengths. From the test results, irrespective of increasing of waste expanded polystyrene resin, the strengths reduction of polymer mortar with waste expanded polystyrene(EPS) resin is not recognized. And the setting shrinkage is reduced with EPS resin content. The waste expanded polystyrene resin as a shrinkage-reducing agent can be used in the same manner as commercial polystyrene resin. In this study, we can obtain the optimum mix proportions of polymer mortar using EPS resin.