• Resources Recycling
• /
• v.17 no.2
• /
• pp.16-29
• /
• 2008

According to the statistical data of the Ministry of Environment, 47million tons of construction waste were generated, and 96.7% of them was recycled in 2005. However, the recycled products seem to be remained under low quality. Because mixed demolition and construction waste, so called DC Waste, including concrete, brick, plaster, lumber, plastics building materials, paper and some dirt and stone, is very variable and difficult to estimate its exact composition, it is regarded as having little or no value to the construction industry. 'The Research group on recycling of construction waste' was started by the Housing & Urban Research Institute(KNHC), which is sponsored as a large scale national project by the Ministry of Construction and Transportation. This research group intends to establish recycling system through planing, processing, developing practical technology, and eventually contribute to save natural resource and to vitalize the industry. In this paper an overview of DC waste management and recycling technology is given in some detail. Particularly, "recycling law of construction waste" and recent research trends on recycling of construction waste are discussed.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.4
• /
• pp.41-48
• /
• 1999

This study was intended to investigated the effect of pulp type and intital calendering on the properties of recycled fiber. As the number of recycling is increased, at least by the fourth recycling , the freeness of the SW-BKP and HW-BKP increased. And then that decrease after the fifth recycling. Especially the freeness of CTMP increased more rapidly than any other pulp in first recycling. And there was no difference of freeness in all kind of pulp by initial calendering . The speed of dewatering in making sheet consistetly became slow by proceeding recycling on condition of all calendering. and the order of the speed of dewatering was as followed. CTMP>HW-BKP>SW-BKP. However in case of HW-BKP, which was low -yield pulp, the tendency of the speed of dewatering was similar to that of CTMP which was high-yield pulp and had high content lignin . There was no change of fiber length and no effect of calendering by recycling of HW-BKP and CTMP. Howeverfiber length of SW-BKP generally decreased, especially in calendering of high temperature and high pressure conditions. The WRV of SW-BKP diminished by proceeding recycling but that of HW-BKP and CTMP diminished in the first recycling and then there was no change of the WRV of HW-BKP and CTMP. The contents of fines of HW-BKP consistently decreased by the fourth recycling and then increased in the fifth recycling . On the other hand there was no tendency in the content of fines of SW-BKP and CTMP by the number of recycling.

• Resources Recycling
• /
• v.21 no.4
• /
• pp.16-25
• /
• 2012

There are several kinds of batteries such as zinc-air battery, lithium battery, Manganese dry battery, silver oxide battery, sodium-sulphur battery, lead acid battery, metal hydride secondary battery, nickel-cadmium battery, lithium ion battery, alkaline battery, etc. These days it has been widely studied for the recycling technologies of the used battery from view points of economy and efficiency. In this paper, patents and published papers on the recycling technologies of the used battery were analyzed. The range of search was limited in the open patents of USA (US), European Union (EU), Japan (JP), Korea (KR) and SCI journal articles from 1972 to 2011. Patents and journal articles were collected using key-words searching and filtered by filtering criteria. The trends of the patents and journal articles were analyzed by the years, countries, companies, and technologies.

• Ceramist
• /
• v.14 no.2
• /
• pp.7-14
• /
• 2011

This paper has investigated physicochemical properties and conventional and environmental-friendly treatment methods of paper mill sludge to emphasize the importance and necessity of the sludge recycling. The paper mill sludge generally shows high contents of calcium and water, and is mostly discharged by landfill after incineration process rather than being recycled due to technical or economical problems. In recent years, however, several possible methods for recycling the paper mill sludge have been suggested for its sustainable process as follows; compost, raw material for the construction and paper industry, new energy source for reducing fossil fuel use and raw material of activated carbon for treating paper mill wastewater. Thus the authors suggest that practical recycling technologies of the paper mill sludge must be developed for substantiality in the paper industry through comprehending physicochemical compositions and generation status of the sludge and actively performing various related studies. Furthermore, this investigation could be used as preliminary information for the study on recycled paper development using paper mill sludge incineration ash.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.361-365
• /
• 1999

This study examined the effects of multiple recycling on deinkability and properties of recycled paper from laser computer printout (LCPO). First, alkaline paper with a 20% printed area was disintegrated by TAPPI standard disintegrator at room temperature. After dewatering, the pulp was flotated and dried in oven at80$^{\circ}C$ for 24 hrs. A sequence of wetting, disintegrating, flotating and drying was one recycling cycle and this cyclic treatment was repeated from zero to five times. The recycled handsheet dropped to 90% of the original brightness after five cycles, and lost the most brightness after five cycles, and lost the most brightness in the first two cycles. However, it had a gain of 10% in opacity after five cycles as the same as the case of nonprinting. And, in this study, the method for determining residual ink(toner) content in recycled handsheets ere established by means of SEM-EDX and Py-GC. The change of residual ink percentage on recycled paper showed the effect of recycling numbers on deinkability of waste paper. A slight decrease in deinkability was noted for the recycled handsheets, which may be due to the change of fiber surface free energy connected with fiber swelling.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.3
• /
• pp.42-47
• /
• 2008

For the purpose of reduction of production cost in the industrial papermaking process, the use of waste paper has been more and more increased as a fibrous raw material, and the closed system of white water became closed more than ever. "Scum" indicates the floated sludge by a flotation during primary wastewater treatment process in paper mills. If the scum is used as the raw material, it could reduce both the raw material and solid waste treatment cost with even small quantity. In this study, the element survey and the toxicity measurement was carried out for recycling scum. A load factor of stock preparation process in paper mills was measured by somerville screen. Physical properties of paper sheet containing the accepted scum from the stock of AOCC or KOCC were evaluated. The result of this study shows that recycling scum has potential to be used in paper making system. It also might be able to reduce the required energy used by the pressing or drainage process, the raw material cost, and solid waste treatment cost due to the recycling of scum.

• Resources Recycling
• /
• v.19 no.2
• /
• pp.63-72
• /
• 2010

The patents were searched to investigate the trend of recycling technologies about plastic waste. Database was collected from WIPS site and the range of the search was limited to patents opened in U.S.A (US), European Union (EU), Japan (JP) and Korea (KR) to september 2009. In this paper, 4,795 patents were selected by investigation abstracts and the trend of the recycling technologies relating to waste plastic were investigated through the analyzing by the years, countries, companies. The patents were occupied 65% by Japan and the most of the patents were about chemical recycling. In the case of Korea, material recycling was major in the patents of waste plastic recycling.

• Resources Recycling
• /
• v.10 no.2
• /
• pp.3-12
• /
• 2001

Nowadays, countries all over the world are deeply concerned about pollution in the global environment, so they are seeking various ways to adequately disposal of waste. Still, the environmental situation seems to be getting worse and worse. It is evident that such wastes and pollution have been endangering human life nestled in this globe up to the end of the 20th century. We should not, however, tolerate such human misconduct and mal-management of resources any more in the new millenium. For realizing a society that is sustainable for generations to come, it is important to establish a social system for minimizing wastes, promote re-use and recycling, and develop technology for improving recycling efficiencies, including product designs that facil-itate re-use and recycling and innovative technologies for processing wastes. In this paper, reviewing the current status of Korean waste problems, the governmental policy and specific approach for the establishment for recycling society is considered.

• Resources Recycling
• /
• v.14 no.3
• /
• pp.3-5
• /
• 2005

On July 5,2002 the Law Concerning Recycling of End-of Life Vehicles popularly known as the "Automobile Recycling Law" was enacted in Japan. This paper examines the features of this Law, reasons why the Law was brought into existence, and its predicted impacts on the automobile industry. Pursuant to the Law, the current automobile recycling system was replaced by a new one in January 1, 2005.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.5-14
• /
• 2000

The treatment of technical consumer products after using is important for the conservation of our environment. In this paper the demanufacturing technology that is required to maximize the recycling rate of end-of-life products is introduced, The definitions including types of the recycling are described. The factors that have to regard in the design stage of products in order to maximize the recycling rate of the products are introduced. The objective assessment methods for the design for environment are described. Finally disassembly process and future prospect of the automations are discussed.