• Journal of Advanced Navigation Technology
• /
• v.14 no.5
• /
• pp.655-660
• /
• 2010

This paper examines RF-to-DC conversion efficiency of rectifying circuit for wireless power transmission. The rectifying circuit consists of low pass filter, diode circuits and dc pass filter. All these components may be effect on the conversion efficiency. Using the simulation, we study these components how to effect on the conversion efficiency. On the basis of the simulation results, the 912MHz rectifying circuit with 50% efficiency at low input power such as 0dBm is fabricated and its characteristics are measured.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.368-371
• /
• 2020

In this paper, we propose a linear tapered slot rectifying antenna for a portable UHF-band RFID system. Since the proposed rectifying antenna does not use a dielectric substrate, the planar antenna is implemented with a thin metal thickness. The rectifier circuit converts input RF power into output DC voltage using a voltage doubler circuit based on two anti-parallel schottky diodes. The rectifying antenna is integrated by the voltage doubler circuit into a linear tapered slot antenna. For conjugate impedance matching of the rectifying circuit and the linear tapered slot antenna, the source-pull method was utilized by adjusting the angle of the tapered slot and the length of the antenna feed line. The proposed antenna prototype has been verified with the electrical and radiation characteristics through RF-DC conversion and far-field radiation test in open space measurement environment. Finally, the proposed antenna is realized to 0.23-wavelength (75 mm) and 0.18-wavelength (60 mm) at 915 MHz center frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.12
• /
• pp.2642-2648
• /
• 2010

The design of coupling and rectifying circuits for the maritime VHF digital modem is investigated in this paper. To monitor the transmitting power of the modem, a directional coupler which is used to extract a small fraction of the transmitter signal power, and a rectifying circuit which make DC voltage proportional to the coupled rf power are designed and fabricated. The parallel-coupled line coupler with directivity of above 25 dB at 160 MHz bands is designed and it is shown that the output voltage of the rectifying circuit is linearly changing from 0.85 V to 1.6 V when the transmitting power of the modem is varying from 1 W to 25 W. The proposed coupler and rectifying circuits are expected to be suitable for maritime VHF digital modem.

• Journal of Korea Society of Industrial Information Systems
• /
• v.16 no.4
• /
• pp.1-7
• /
• 2011

In this paper, we design rectifing circuits at 910MHz, which is used for passive RFID system, for wireless power transmission system by using two types of schottkey diodes HSMS_2822 and HSMS 2852, and the RF-DC conversion efficiencies for the curcuits are compared and analyzed in terms of input power and load resistance. When the input power is -20 to 17dBm, the conversion efficiency for HSMS_2852 is larger than in case of HSMS_2822. The output voltage and current at the load of the fabricated rectifying circuit are measured through a dipole antenna when input power is transmitted by a RFID reader and the diatance varies. The measured ouput volatge and current for the distance of 50cm are 2.5V and 5.75mA.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.3
• /
• pp.208-216
• /
• 2018

In this paper, an LLC resonant converter employing two coupled inductors on the secondary side of the converter is proposed. The conventional LLC converter exhibits serious power loss during secondary winding of the transformer because of generation of tremendous output current ripples. To overcome this problem, an LLC resonant converter with a current doubler as a rectifying circuit was recently proposed. However, the current-doubler rectifying circuit requires coupled inductors with a high coupling ratio to retain the designed resonance characteristics. Therefore, an additional hardware filter is required at the output stage to address large output current ripples. Additional design procedures are also necessary because the inductance component of the added filter affects the designed resonant network. To solve this issue, an LLC resonant converter employing two coupled inductors is proposed in this paper. Mathematical analysis shows that the proposed secondary-side current-doubler circuit does not affect the designed resonance characteristics. The operating principles and theoretical analyses are proven through a simulation and experiments with a 54 V/28 A prototype.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.267-271
• /
• 1990

This paper describes a 3-Phase Quasi-Resonant DC Link Inverter (3-phase QRI), which has two operating modes, ie. inverting mode and rectifying mode. First the 3-Phase QRI is simplified and the resonant circuit is analyzed in comparison with two resonant DC-to-DC converters. This analysis shows that the maximum voltage of resonant capacitor is limited to twice the input voltage irrespective of operating modes. A new simple control method in rectifying mode is suggested, which does not require any other element in power circuit. The characteristic of 3-Phase Quasi Resonant Inverter has been verified by simulation using the proposed control method.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.559-562
• /
• 2000

The problem of noise generation due to PWM switched-mode power converter has been widely noticed from the viewpoint of Electromagnetic Interference(EMI). Many kings of topologies for resonant converters have been developed both to overcome this noise problem and to attain high power efficiency. It is reported in references that resonant converters which are derived from PWM converter using resonant switch show much lower noise characteristics than PWM converter, and that current-mode resonant converter is more sensitive to stored charge in rectifying diode than voltage-mode counterpart concerning surge generation at diode’s turn-off. On the other hand, above mentioned resonant converters have defect of high-voltage stress on semiconductor switch and complicated circuit configuration. Hence, the simplified Forward-type resonant converter has been proposed and investigated due to its prominent features of simplicity of circuit configuration, low voltage stress and high stability. However, its noise characteristics still remain unknown. The purpose of this paper is to study quantitatively the noise characteristics of this simplified Forward-type resonant converter by experiment and analysis. The influence of parasitic elements and stored charge in rectifying diode on noise generation has been clarified.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.6
• /
• pp.916-926
• /
• 1994

A high frequency and soft-switched AC-to-DC rectifier employing a series-type resonant circuit is proposed to overcome the disadvantages of the conventional peak-rectifying circuit. Using the proposed rectifier, the high power factor and low harmonic currents are obtained in the AC line. Furthermore, several advantages such as the high power density and wide output voltage range can be available. Through the simulation and experimental results, the usefulness of the proposed rectifier is verified.

• Korean Journal of Materials Research
• /
• v.26 no.2
• /
• pp.84-89
• /
• 2016

We present the rectifying and nitrogen monoxide (NO) gas sensing properties of an oxide semiconductor heterostructure composed of n-type zinc oxide (ZnO) and p-type copper oxide thin layers. A CuO thin layer was first formed on an indium-tin-oxide-coated glass substrate by sol-gel spin coating method using copper acetate monohydrate and diethanolamine as precursors; then, to form a p-n oxide heterostructure, a ZnO thin layer was spin-coated on the CuO layer using copper zinc dihydrate and diethanolamine. The crystalline structures and microstructures of the heterojunction materials were examined using X-ray diffraction and scanning electron microscopy. The observed current-voltage characteristics of the p-n oxide heterostructure showed a non-linear diode-like rectifying behavior at various temperatures ranging from room temperature to $200^{\circ}C$. When the spin-coated ZnO/CuO heterojunction was exposed to the acceptor gas NO in dry air, a significant increase in the forward diode current of the p-n junction was observed. It was found that the NO gas response of the ZnO/CuO heterostructure exhibited a maximum value at an operating temperature as low as $100^{\circ}C$ and increased gradually with increasing of the NO gas concentration up to 30 ppm. The experimental results indicate that the spin-coated ZnO/CuO heterojunction structure has significant potential applications for gas sensors and other oxide electronics.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.4
• /
• pp.506-511
• /
• 2011

In this paper, a rectenna for wireless power transmission at 900MHz is proposed. Rectenna is a device transforming RF power into DC power and it may consist of a antenna, rectifying and charging circuits. In this paper, we designed a slot antenna to receive 900MHz signal, a rectifying circuit of about 40% efficiency at 0dBm input, and a charging circuit to store a weak power signal and supply constant voltage to load. From the experiment using a RFID reader as a transmitter for 1W power, it was found that the proposed rectenna receiving about 0dBm power can supply 3.3V constant voltage to 50$k{\Omega}$ load during 280sec.