• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.88-91
• /
• 2005

Although the MEMS element is made through a very precise manufacturing process, usually there is the difference between the modeling design and the actual product. So tuning is required. Through the frequency tuning(changing the characteristics of device), we can calibrate the fabrication error and uncertainty. I'll propose the method of changing the natural frequency through the imposing the axial force on the anchor part to separate the sensing part and the tuning part. When the shape of section is the form of rectangular, the degree of the natural frequencies' change under axial force appears D be different. Applying a tuning force of 30 $\mu$N, the natural frequencies' difference can be reduced by 5 percent.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.104-113
• /
• 1993

Characteristics of fiber-reinforced thermoplastic sheet depend on the quantity and shape of fibers. During a molding process of composites, the fiber-maxtrix separation and fober orientation are caused by the flow during the molding process. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation-orientation and molding conditions. The correlation between the separation and the orientation have to be clarified for designing the fiber structure. In this paper, the degree of nonhomogeneity which is a measure of the separation is obtained using one-dimensional rectangular shaped part compression molding. And the orientation function is defined and measured by the image processing using soft X-rayed photograph and image scammer. Correlation between the degree of nonhomogeneity and the orientation function is discussed.

• Journal of Digital Convergence
• /
• v.11 no.8
• /
• pp.199-204
• /
• 2013

Computational fluid dynamics (CFD) is used to reduce number of experiments. The CFD tools are widely used for engine design and flow pattern analysis to reduce experiments. In this study the performance of a PEMFC single cell was analyzed by using STAR-CD, product of CD-ADAPCO. The effect of cell design and flow pattern on the performance of a PEMFC was analyzed with the 3-D simulation. As a result the performance of rectangular cell was the higher than that of square cell, while the flow direction scarcely affected on the performance of a PEMFC. Also the current density according to different excess ratio of air flow rate was compared and analyzed. The difference between maximum and minimum current density of flip-flow was lower than that of co-flow.

• Progress in Medical Physics
• /
• v.13 no.1
• /
• pp.27-31
• /
• 2002

Output factors for 6MeV electron were directly measured under the condition of an individual beam cutout and these factors were compared with the output factors by 1D method which is an easy means to predict the output factors of electron beam. Output factors by 1D method are defined as output factors of rectangular fields where one side is always equal to the side of the square reference field and the output of an arbitrary rectangular field X, Y is given by the product of the 1D output factors. The output of very large square fields is overestimated using 1D method for the 6MeV electron, but it results in agreement with measured data under the condition of an individual cutout within 1% error adopting a correction factor $CF=C\times$[(X-10)(Y-10)/$\mid$(X-10)(Y-10)$\mid^{1/2}]$.

• Korean Journal of Materials Research
• /
• v.6 no.8
• /
• pp.768-778
• /
• 1996

Iron oxide (hematite, $\alpha$-${Fe}_{2}{O}_{3}$) particles were prepared directly from aqueous solution using a crystal growth controller. Paticles properties and reaction mechanisum of products as a function of basicity, formation process and mechanism of needle-lkie hematite were investigated. hexagonal hermatite particles were formed in teh range below pH 9.0, ellipsoidal or rectangular hematite particles in the range of pH 10.75-11.75 respectively. In the range above pH 12.50, acicular $\alpha$-FeOOH was formed. Basicity of product solution produced in the range of pH 10.7511.75 was increased slightly as compared with basicity of reastants due to hydroxly ion(OH-) formed by dissociation crystal growth controller. Citric acid which is acted as a crystal growth controller was adsorbed in the form of itrate anion(R-COO-) on the ferric hydroxide and exerted important role on the formation to the needle-like $\alpha$-${Fe}_{2}{O}_{3}$ particles in this reaction system.

• Journal of Ship and Ocean Technology
• /
• v.10 no.2
• /
• pp.24-36
• /
• 2006

Ship hullform is usually designed with a curve network, and smooth hullform surfaces are supposed to be generated by filling in (or interpolating) the curve network with appropriate surface patches. Tensor-product surfaces such as B-spline and $B\'{e}zier$ patches are typical representations to this interpolating problem. However, they have difficulties in representing the surfaces of irregular topological type which are frequently appeared in the fore- and after-body of ship hullform curve network. In this paper, we proposed a method that can automatically generate discrete $G^1$ continuous B-spline surfaces interpolating given curve network of ship hullform. This method consists of three steps. In the first step, given curve network is reorganized to be of two types: boundary curves and reference curves of surface patches. Especially, the boundary curves are specified for their surface patches to be rectangular or triangular topological type that can be represented with tensor-product (or degenerate) B-spline surface patches. In the second step, surface fitting points and cross boundary derivatives are estimated by constructing virtual iso-parametric curves at discrete parameters. In the last step, discrete $G^1$ continuous B-spline surfaces are generated by surface fitting algorithm. Finally, several examples of resulting smooth hullform surfaces generated from the curve network data of actual ship hullform are included to demonstrate the quality of the proposed method.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.373-377
• /
• 2009

Most of the plastics products are being manufactured by injection molding. Warpage in injection molded affects the product dimension and it causes assembling problem. In this study, warpages in the injection molded part been studied. Specimens are rectangular flat shapes with and without ribs. Amorphous polymers (PC and ABS) and crystalline polymers (PP and PA66) were used for material. Flat shape with ribs showed higher warpage than flat shape without ribs by 6 to 9%. The specimens with ribs that are located parallel to the flow direction has higher warpage than specimens with ribs that are located perpendicular to the flow direction by 25 to 39%. Crystalline polymers have higher warpage than amorphous polymers by 23 to 67%. Warpage decreases as packing time increases and it increases as injection temperature increases.

• Journal of Adhesion and Interface
• /
• v.21 no.3
• /
• pp.93-100
• /
• 2020

3D printing technology enables proper objects to be made through an additive manufacturing method, but resulting in dimension deviation of the product due to contraction phenomenon as cooling melted filament resin injected from high-temperature use environment. In this research, we studied on acrylic adhesives for 3D printer build sheet in order to fabricate high-quality products with a precise shape and to well-mount without distortion. The solvent-free UV-curable acrylic adhesive formulation was designed by adding 4-acryloylmorpholine (ACMO) with high adhesion, toughness, glass transition temperature so that adhesion properties are stable at high temperature and products are easily mounted/detached from the adhesives. The designed formulation was polymerized through two-steps using post-addition of monomers. Using this, the acrylic adhesive was coated to make a film and then analyzed using various experimental techniques. As a result, the fabricated adhesive exhibited high glass transition temperature and there was little gap in peel strength before and after thermal treatment. Moreover, it was confirmed by rheological analysis that this adhesive can provide great bonding/debonding ability without distortion. We demonstrated the fabrication of a rectangular product using a 3D printing method using our acrylic adhesive as a build sheet. Mounting ability and workability were satisfactory and dimension deviation of the product was tiny. Because the product is easily detachable from the acrylic adhesive developed here than conventional build sheets, it is expected that this will provide work convenience to users who use the 3D printer.

• Science of Emotion and Sensibility
• /
• v.13 no.1
• /
• pp.91-102
• /
• 2010

This study investigates the dominant degree of product design factors through the process of change of design factors. The previous research suggested a concrete measurement method of dominant designs, but it did not investigate empirically the degree of dominance due to the limited data for changes of designs. In this research, thus, after collecting design data of mobile phones and we measured the dominance and structure change of the designs by year. The analyses showed the following two things. First, in design factors of mobile phone the dominance on the body form and the edge grows more and both of them as dominant design factors tend to converge into the rectangular body form and the round edge, respectively. Second, the dominance on other design factors(e.g. the button type, the open type, whether or not to have digital multimedia broadcasting(DMB) and video telephony functions, the combination of colors and the body color) increases and decreases; and hence, design levels tend to diverge. In conclusion, the measurement of dominance on product design factors contributes to marketing managers and designers who are required to establish a strategy for products under the rapidly changing circumstances of market. This research aims to provide those managers and designers with a guide line for a successful development of new product to prepare for the dominant design from this empirical study.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.67-72
• /
• 2012

Most of the plastics products have been manufactured by injection molding. Molding trouble in injection-molded parts is caused by changing a molding product and molding process condition, etc. In this study, warpage in the injection molded part have been studied. Specimens are rectangular flat shape with and without ribs. Non-crystalline resins (ABS+GF30%, PC+GF30%) and crystalline resins (PP+GF30%, PA66+GF30%) were used for material. Flat shape ribs showed higher warpage than flat shape without rib by 10 to 41%. the specimens with ribs that are located parallel to flow direction has higher warpage than the specimens with rib that are located perpendicular to flow direction by 11 to 50%. crystalline resins have higher warpage than non-crystalline resins by 22 to 78%. Warpage decreases as packing time increases as injection temperature increases.