• 콘크리트학회논문집
• /
• 제29권2호
• /
• pp.179-187
• /
• 2017

철근콘크리트 휨 부재의 최대철근비에 대한 설계 규정은 일반적으로 부재 파괴 시 철근이 항복하도록 하여 충분한 연성과 경제성을 보장 하도록 하고 있다. 콘크리트구조기준(2012)에서 최대철근비는 인장 철근의 순인장변형률 항으로 표현되고, 고강도 재료가 사용되는 경우 매우 높은 철근비를 나타낸다. 따라서 이는 콘크리트 타설시 시공성 확보에 어려움을 야기할 수 있다. 이에 반해, 도로교설계기준(한계상태설계)에서는 최대중립축 깊이비가 0.4가 되도록 최대철근비를 규정하고 있다. 이 결과로부터 시공성 및 연성을 확보할 수 있는 최대철근비에 대한 합리적인 모델을 제시하였다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.189-195
• /
• 2000

New concept of LNG-FPSO ship with moonpool and bilge step in bottom is considered and investigated in the point of motion reduction and sloshing phenomena of the cargo and operation tanks. The cargo capacity of the ship of which principle dimensions is L x B x D x t(design) =270.0 x 51.0 x 32.32 x 13.7(m) 16K at 98% loading condition. The two moonpools and rectangular step at bilge part are setted up specially for getting the effect of motion decrease. For the motion analysis, linearized three dimensional diffraction theory with the simplified boundary conditions is used. The six-degree of freedom coupled motion responses are calculated for the LNG-FPSO ship. Viscous effects on the roll motion responses of a vessel are taken into account in this calculation program using an empirical formula suggested by Ikeda, Himeno and Tanaka is used. The case study for the moonpool size had been carried out by theoretical estimation and experimental method. For the optimization of the moonpool size and effect of the step, 9 cases of its size and with and without step are considered. From the results of calculation and experiment, it can be concluded that this designed LNG-FPSO ship have possibility to carry out her missions in the rough sea as for the owner's demand waves condition. The motion responses, especially roll motion, for the designed LNG-FPSO ship are much lower than those of another drillship and shuttle tanker and limit criterions are satisfied. For the check of the cargo tank and operation tank sizes we have performed sloshing analysis in the irregular waves which focuses on the pressure distribution on the tank wall and the time history of pressure and free surface for No.2 and No5. tanks of LNG-FPSO with chamfers. Finally we got the tank size which has no resonance and no impact pressure in all filling in the bow quartering and beam sea.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.28-37
• /
• 1999

This investigation is the result of the structural analysis by finite element method and test for considering stress distribution and stress concentration to be generated according to the change of attached shape and method of the bracket to pipe in welding structure. Generally, members that consist structures are subjected to various forces and are jointed each other with a number of bracket. In this case, circular pipe was adapted in order to weld these members easily and to study the optimal design which is used a beam with shape section as main components of the structure, According to attached shape and method, distributed stress on circular pipe is appeared so differently. This may result deeply effects with respect to thickness, material properties. So a study on attaching shape and method of bracket to circular pipe is needed. In this paper, to obtain the maximum equivalent stress or stress concentration was used experimental and F.E.M. analysis. First five parameter was defined with respect to attached a shape and method to circular pipe i.e. the variation of the attached area, the variation of the attached shape, the variation of the attached length, the variation of both directin angles, the variation of the upper angle. Afterward the experimental analysis was practiced as the variation of the both direction angel and the finite element analysis was practiced as each parameters. We can discover stress distribution and stress concentration according to the change of form of bracket. And the result can be referenced for a design of similar structure.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.54-65
• /
• 1997

To quantify the LII signals from soot particle of flames in diesel engine cylinder, a new method has been proposed for correcting LII signal attenuated by soot particles between the measuring point and the detector. It has been verified by an experiment on a laminar jet ethylene-air diffusion flame. Being proportional to the attenuation, the ratio of LII signal at two different detection wavelengths can be used to correct the measured LIIsignal and obtain the unattenuated LII signal, from which the soot volume fraction in the flame can be estimated. Both the 1064-nm and frequency-doubled 532-nm beams from the Nd : YAG laser are used. Single-shot, one-dimensional(1-D) line images are recorded on the intensified CCD camera, with the rectangular-profile laser beam using 1-mm-diameter pinhole. Two broadband optical interference filters having the center wavelengths of 647 nm and 400 nm respectively and a bandwidth of 10 nm are used. This two-wavelength correction has been applied to the ethylene-air coannular laminar diffusion flame, previously studied on soot formation by the laser extinction method in this laboratory. The results by the LII measurement technique and the conventional laser extinction method at the height of 40 nm above the jet exit agreed well with each other except around outside of the peaks of soot concentration, where the soot concentration was relatively high and resulting attenuation of the LII signal was large. The radial profile shape of soot concentration was not changed a lot, but the absolute value of the soot volume fraction around outside edge changed from 4ppm to 6.5 ppm at r=2.8mm after correction. This means that the attenuation of LII signal was approximately 40% at this point, which is higher than the average attenuation rate of this flame, 10~15%.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권2호
• /
• pp.82-89
• /
• 2014

이 연구에서는 고로슬래그 미분말을 사용한 프리캐스트 보의 전단성능에 대하여 평가하였다. 실험체는 고로슬래그 미분말 치환율에 따라 총 4체의 실험체를 제작하였다. 모든 실험체는 전단경간비 2.5, 보의 폭 200mm, 유효깊이 300mm이며, 3점 가력을 받는 단순보로 계획하였다. 또한 이 연구에서는 실험체의 전단강도를 예측하기 위하여 기존 전단강도 예측식을 이용하여 실험결과와 비교하였으며, 총 89개의 기존 전단 실험결과를 이용하여 실험결과와 비교 분석하였다. 실험결과, 고로슬래그 미분말을 치환한 실험체는 포틀랜드 시멘트만을 사용한 실험체와 비교분석한 결과 유사한 전단성능을 나타내었다.

• 한국방재학회 논문집
• /
• 제8권3호
• /
• pp.67-75
• /
• 2008

본 논문은 형강을 이용한 강-콘크리트 합성복공판 기술개발에 관한 것이다. 기존의 롤포밍 단면을 배제하고 형강을 이용하여 효율적인 강합성 단면을 구성함으로써 제작성과 경제성을 확보하고, 전단연결재의 개선을 통해 합성성능 뿐만 아니라 차후 콘크리트와 강재의 분리에 용이한 구조를 개발하였다. 성능검증 실험결과 기존의 전단연결재만으로는 강재와 콘크리트의 합성거동을 이루는데 한계가 있음을 확인하였다. 나아가 개발 복공판은 설계하중대비 5배 이상의 극한 내하력을 확보하고 있으며, 200만회 피로성능시험에 대해서도 손상이 거의 발생하지 않으며 우수한 구조성능을 나타냈다. 따라서, 형강을 이용한 합성단면 구성을 통해 구조성능 확보뿐만 아니라 기존 합성복공판 대비 약 27% 정도의 강재량 감소가 가능함을 확인하였다.

• 해양환경안전학회지
• /
• 제13권3호
• /
• pp.219-222
• /
• 2007

본 논문에서는 800MHz대역의 TRS(Trunked Radio System)대역을 비롯한, GSM(Global System for Mobile telecommunication), CDMA(Code Division Multiple Access)대역을 통합할 수 있는 광대역 마이크로스트립 안테나를 설계하고자 한다. 선박 및 해상 안전에 상용 가능한 선박 기지국 중계기용 안테나를 설계하였다. 마이크로 스트립 안테나의 협대역을 개선하기 위해서 직사각형 패치에 L형 급전구조를 갖으며, 평행 L-슬롯을 추가하여 이중 공진 효과를 이용하였다. 또한 이득의 개선을 위해 수직으로 적층 하였다. 설계된 안테나의 주파수 대역폭(VSWR 2:1)은 748MHz${\sim}$1.04GHz로 292MHz(36%)의 양호한 특성을 보였으며, 또한 E-평면과 H-평면 모두 이득은 6.4Bi 이상, 3dB 빔폭은 E-평면 $44.7^{\circ}와 H-평면 $61.8^{\circ}이상의 개선된 특성을 보였다.

• Restorative Dentistry and Endodontics
• /
• 제24권4호
• /
• pp.604-613
• /
• 1999

This study was performed to evaluate the effect of resin and filler type on the fracture toughness of light-activated composites. Experimental composites were prepared using urethane tetramethacrylate(UTMA) and bisphenol glycidylmethacrylate(Bis-GMA) monomers and five different types of silica fillers. Fracture toughness was measured by a single edge V-notched beam(SEVNB) method, which was discussed from ASTM E399-78. Rectangular bars of $2.5{\times}5{\times}26mm$ were prepared with experimental composites and a notch about 2.25mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed of 0.05mm/min and fracture surfaces were observed under scanning electron microscope. The results obtained were summarized as follows: 1. The fracture toughness values of UTMA-based composites were relatively higher than those of Bis-GMA-based composites. 2. The highest fracture toughness value was observed in the UTMA-based composite containing the $1.5{\mu}m$-spherical fillers. 3 Aging in the distilled water at $37^{\circ}C$ for 10 days showed the increase of fracture toughness, which was severer in the Bis-GMA-based composites than those of UTMA-based composites. 4. The AE amplitude occurring during the fracture toughness tests was the highest at the point of macroscopic fracture.

• 전산구조공학
• /
• 제10권4호
• /
• pp.315-325
• /
• 1997

본 논문에서는 이산성 연속형 최적성규준방법을 이용하여 다지간 부분프리스트레스트 콘크리트보의 최적설계 알고리즘을 유도하였고, 최적설계프로그램을 개발하였다. 목적함수로서 건설 경비는 콘크리트 경비, 긴장재 경비, 철근 경비, 그리고 거푸집 경비를 포함하였으며 이를 최소화하였다. 설계제약조건으로는 시방서상의 최대처짐제약, 휨 및 전단강도제약, 연성제약 그리고 설계변수에 대한 상.하한계제약을 고려하였다. Kuhn-Tucker 필요조건을 이용하여 최적성규준을 설계변수의 항으로 명시적으로 유도하였으며, 이때 설계변수로는 보의 유효깊이, 긴장재의 편심거리 그리고 철근비를 취하였다. 긴장재의 형상은 포물선함수로 고려하였으며, 구조물 자중의 영향은 긴장력에 의한 이차효과와 마찬가지로 실제시스템의 평형방정식에서 고려하였다. 설계변수들의 개선을 위한 반복과정과 컴퓨터프로그램을 개발하였으며, 수치예를 들어 개발된 기법의 응용성 그리고 효율성을 보였다.

• Structural Engineering and Mechanics
• /
• 제53권2호
• /
• pp.311-324
• /
• 2015

The purpose of this study was to investigate experimentally the fatigue performance of reinforced concrete (RC) beams with hot-rolled ribbed fine-grained steel bars of yielding strength 500MPa (HRBF500). Three rectangular and three T-section RC beams with HRBF500 bars were constructed and tested under static and constant-amplitude cyclic loading. Prior to the application of repeated loading, all beams were initially cracked under static loading. The major test variables were the steel ratio, cross-sectional shape and stress range. The stress evolution of HRBF500 bars, the information about crack growth and the deflection developments of test beams were presented and analyzed. Rapid increases in deflections and tension steel stress occured in the early stages of fatigue loading, and were followed by a relatively stable period. Test results indicate that, the concrete beams reinforced with appropriate amount of HRBF500 bars can survive 2.5 million cycles of constant-amplitude cyclic loading with no apparent signs of damage, on condition that the initial extreme tensile stress in HRBF500 steel bars was controlled less than 150 MPa. It was also found that, the initial extreme tension steel stress, stress range, and steel ratio were the main factors that affected the fatigue properties of RC beams with HRBF500 bars, whose effects on fatigue properties were fully discussed in this paper, while the cross-sectional shape had no significant influence in fatigue properties. The results provide important guidance for the fatigue design of concrete beams reinforced with HRBF500 steel bars.