• Resources Recycling
• /
• v.29 no.6
• /
• pp.27-34
• /
• 2020

In order to remove sulfate(SO42-) and purify the Li2CO3, dissolution and recrystallization of crude Li2CO3 using distilled water and HCl solution was performed. When Li2CO3 was dissolved using distilled water, the amount of dissolved Li2CO3(wt.%) increased as the solution temperature decrease and showed about 1.50 wt.% at 2.5℃. In addition, when Na2CO3 was added and the Li2CO3 solution was recrystallized, the recrystallization(%) increased with increasing temperature, resulting in a 49.00 % at 95 ℃. On the other hand, when Li2CO3 was dissolved using HCl solution, there was no effect of reaction temperature. As the concentration of HCl solution increased, the amount of dissolved Li2CO3(wt.%) increased, indicating 7.10 wt.% in 2.0 M HCl solution. When the LiCl solution was recrystallized by adding Na2CO3, it exhibited a recrystallization(%) of 86.10 % at a reaction temperature of 70 ℃, and showed a sulfate ion removal(%) of 96.50 % or more. Finally, more than 99.10 % of Na and more than 99.90 % of sulfate were removed from the recrystallized Li2CO3 powder through water washing, and purified Li2CO3 with a purity of 99.10 % could be recovered.

• Advances in materials Research
• /
• v.3 no.4
• /
• pp.217-225
• /
• 2014

In this study, a forging steel alloyed with both Nb and V was used as experimental material and the hot deformation behavior has been studied for this steel by conducting the compressive deformation test at temperature of $900-1150^{\circ}C$ and strain rate of $0.01-0.01s^{-1}$ in a MMS-300 thermo-mechanical simulator. The microstructure evolution, particularly the dynamically recrystallized microstructure, of the experimental steel at elevated temperatures, strain rates and strain levels, was characterized by optical microstructural observation and the constitutive equation in association with the activation energy and Zener-Hollomon parameter. The curves of strain hardening rate versus stress were used to determine the critical strain and peak strain, and their relation was connected with Zener-Hollomon parameter. Under the conditions of processing temperature $900^{\circ}C$ and strain rate $0.01s^{-1}$, the dynamic recrystallization took place and the austenite grain size was refined from $164.5{\mu}m$ to $28.9{\mu}m$.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.5
• /
• pp.346-354
• /
• 2000

Effect of Nb addition on the phase transformation behavior was studied through continuous cooling transformation tests after reheating(reheating CCT) and deforming(deforming CCT) the 0.07%C-1.3%Mn-0.015%Ti-(0~0.08)% Nb steels. Transformation temperatures for deforming CCT were lower than those for reheating CCT, and the critical cooling rate for bainite transformation during deforming CCT was lower than that during reheating CCT. These enhanced hardenability for deforming CCT was considered to come from the sufficient solid solution of Nb in austenite during high temperature reheating before deformation. With Nb addition, the phase transformation temperature decreased, the bainite formation was enhanced, and the hardness of steel increased. Furthermore, these phenomena were more remarkable for deforming CCT than for reheating CCT. From the results, Nb-Ti bearing low carbon steel was considered to be a very favorable alloy system with good strength/toughness balance by recrystallization control rolling process.

• Transactions of Materials Processing
• /
• v.3 no.4
• /
• pp.427-439
• /
• 1994

The high temperature deformation behavior of $SiC_p/Al-Si$ composites and Al-Si matrix was studied by hot torsion test in a range of temperature from $270^{\circ}C$ to $520^{\circ}C$ and at strain rate range of $1.2{\times}10_{-3}~2.16{\times}10_{-1}/sec$. The hot restoration mechanisms for both matrix and composites were found to be dynamic recrystallization(DRX) from the investigation of flow curves and microstructural evolutions. The Si precipitates and SiC particles promoted DRX, and the peak strain$({\varepsilon}_p)$ of the composites was smaller than that of the matrix. Flow stresses of $SiC_p/Al-Si$ composites were found to be generally higher than the matrix, but the difference was quite small at higher temperature due to the decrease of capability of load transfer by SiC particles. With increasing temperature, failure strain of matrix and composites are inclined to increase, the increasing value of failure strain for the $SiC_p/Al-Si$ composites was small compared to that of matrix. The stress dependence of both materials on strain rate() and temperature(T) was examined by hyperbolic sine law, $\.{\varepsilon}=A_1[sinh({\alpha}{\cdot}{\sigma})]_n$exp(-Q/RT)

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.453-459
• /
• 2004

25Cr-20Ni series strainless steels have an excellent high temperature strength high oxidation and high corrosion resistance. However, further improvement can be expected of creep strength by work hardening prior creep. In the present study, the effect of prestraining at room temperature on the creep behavior of a Class M(STS310S) and a Class A(STS310J1TB) alloy containing precipitates have been examined. Prestaining was carried out at room temperature and range of prestrain was 0.5-2.5 % at STS310J1TB and 2.0-7.0% at STS310S. Creep behavior and creep rate of pre-strained specimens were compared with that of virgin specimens. Room temperature prestraining produced the creep life that is longer than that of a virgin specimen both for STS310J1TB and STS310S when creep test was carried out at the temperature lower than recrystallization temperature. The reason for this improvement of creep life was ascribable to the interaction between dislocations and precipitates in addition to the dislocation-dislocation interaction in STS310J1TB and the dislocation-dislocation interaction in STS310S. The beneficial effect of prestraining in STS310J1TB was larger than that of STS310S.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.143-146
• /
• 2001

The evolution of dynamic recrystallization (DRX) was studied with torsion test for AISI 304 stainless steel in the temperature range of $900-1000^{\circ}C$ and strain rate range of 0.05-5/sec. The evolution of DRX was investigated with microstructural analysis and change of flow stress curve slope. The investigation of serrated grain boundaries using electron back scattered diffraction (EBSD) analysis indicated that the nucleated new DRX grain size was similar to the size of bulging part. Before the steady state, the dynamically recrystallizing grains do not remain a constant size and gradually grow to the size of fully DRX grain at steady state. The calculation of grain size was based on $X_{DRX}$ and the assumption, which the nucleated DRX grains are growing to the steady state, continuously. It was found that the calculated results agreed with the microstructure of the alloy.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.100-123
• /
• 1995

The relationship between plastic deformation and crystal grain change in warm forging processes of SM100 carbon steel is studied. If the carbon steel is deformed in warm forging temperature (about recrystallization range), the crystal grain and cementite of the internal part are changed, so material properties are changed. Some experimental values, such as the elliptic degree of cementite, the grain size of cementitie and ferrite grain size, are investigated. When the plastic deformation proceeds, the elliptic degree of cementite becomes large, the grain size of cementite particle is small, and the size of ferrite grain appears fine by recrystallization. The elliptic degree of cementite has a considerable effect on formability. The distribution of effective strain in the forging is calculated by the rigid visco-plastic FEM analysis. The effective strain distribution obtained from the FEM simulation is compared with the experimental result. At effective strain 0.3 dynamic recovery and dynamic recrystallization begin, over 2.5 the organization of material has better quality that is suitable for the following cold forming.

• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.331-335
• /
• 2018

This study investigates the directional recrystallization behavior of Ni based oxide dispersion strengthened (ODS) alloy according to the zone annealing velocity. The zone annealing temperature is set as $1390^{\circ}C$, while the zone velocities are set as 2.5, 4, 6, and 10 cm/h, respectively. The initial microstructure observation of the as-extruded sample shows equiaxed grains of random orientation, with an average grain size of 530 nm. On the other hand, the zone annealed samples show a large deviation in grain size depending on the zone velocities. In particular, grains with a size of several millimeters are observed at 2.5-cm/h zone velocity. It is also found that the preferred orientation varies with the zone annealing velocity. On the basis of these results, this study discusses the role of zone velocities in the directional recrystallization of Ni base ODS alloy.

• Transactions of Materials Processing
• /
• v.7 no.5
• /
• pp.450-458
• /
• 1998

The high temperature deformation behavior of Al 5083 alloy has been studied in the temperature range of 350 to 520 ${\circ}C$ and strain rate range of 0.2 to 3.0/sec by torsion test. The strain rate sensitivity(m) of the material was evaluated and used for estabilishing power dissipation maps following the dynamic material model. These maps show the variation of efficiency of power dissipation(${\eta}$=2m/(2m+1)) with temperature and strain rate. Hot restoration of dynamic recrystallization (DRX) was analyzed from the flow curve, deformed microstructure, and processing maps during hot deformation. Also, the effect of deformation strain on the efficiency of power dissipation of the alloy was analysed using the processing maps. Moreover relationship between the hot-ductility and efficiency of power dissipation of the alloy depending on thmperature and strain rate was studied using the Zener-Hollomon parameter(Z=${\varepsilon}$exp(Q/RT) It is found that the maximum efficiency of power dissipation for DRX in Al 5083 alloy is about 74.6 pct at the strain of 0.2. The strain rate and temperature at which the efficiency peak occurred in the DRX domain is found to be ∼0.1/sec and ∼450${\circ}C$ respectively.

• Food Science of Animal Resources
• /
• v.32 no.5
• /
• pp.627-634
• /
• 2012

This study was carried out to investigate the physical and thermal properties of ${\kappa}$-carrageenan (${\kappa}$-car) gel added whey protein isolate (WPI) as a cryoprotectant. The concentration of ${\kappa}$-carrageenan was fixed at 0.2 wt%. The mean ice crystal size of the WPI/${\kappa}$-car was decreased according to increasing whey protein isolate concentration. The temperature of gel-sol (Tg-s) and sol-gel (Ts-g) transition of WPI/${\kappa}$-car maxtrix was represented in the order of 3.0, 0.2, 5.0 and 1.0 wt%. In addition, the transition temperature of gel-sol of WPI in sucrose solution were showed in order of 1.0, 5.0, 0.2 and 3.0 wt% depending on whey protein isolate concentration. The shape of ice crystal was divided largely into two types, round and rectangular form. 1.0 wt% WPI/${\kappa}$-car matrix at pH 7 and 9 showed minute and rectangular formation of ice crystals and whey protein isolate in sucrose solution at a concentration of 1.0 wt% WPI/${\kappa}$-car matrix at pH 3 and 5 showed relatively large size and round ice crystals. The ice recrystallization characteristics and cryprotective effect of ${\kappa}$-carrageenan changed through the addition of different concentrations of whey protein isolate. It seems that the conformational changes induced interactions between whey protein isolate and ${\kappa}$-carrageenan affected ice recrystallization.