• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.296-299
• /
• 2001

Data on the oil spill recovery from the water surface by light floating electromagnetic plants using a new magnetic adsorbent are given. The feasibility scope for further oil recovery from such gathered mixtures(oil+adsorbent), reuse of this magnetic adsorbent and its properly reclaiming and recycling were shown. The basic conception of the oil spill recovery and efficiency of this method were set forth.

• Journal of the Korean Institute of Gas
• /
• v.21 no.5
• /
• pp.27-35
• /
• 2017

The amount and quality of waste heat from a resource recovery facility were measured. The temperature of exhaust gas was $176.6^{\circ}C$ and the amount of that was 13.8 kg/s. This research designed a waste heat recovery system whose working fluid is R-245fa. It simulated three study cases as follows. In simulation of a basic ORC system, the turbine power output and thermal efficiency were respectively 96.56 kW, 14.3%. In simulation of a superheater connection, 0.09% of efficiency could be improved due to the increase of enthalpy by overheating of working fluid, but the obtained output was decreased with 16.58kW because of the decrease of working fluid mass. In simulation of a process heater connection, efficiency was increased up to 38.51%.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.11
• /
• pp.627-634
• /
• 2016

We investigated the characteristics of heavy metal desorption and recovery from carbon foam after plating wastewater treatment. The heavy metal desorption depends on solution chemistry because desorption occurred in HCl and $H_2SO_4 $ solution but did not occur in distilled water. Heavy metal desorption efficiency was increased using ultrasonication with desorption solution. The higher ultrasonic power and the longer reaction time improve efficiency. The copper plating rinse solution was treated reliably by carbon foam adsorbent during 200 bed volume. The adsorbed copper was dissolved using desorption solution and recovered by DC power supply. After copper recovery, the reuse efficiency of desorption solution was 84.2%.

• Journal of Animal Reproduction and Biotechnology
• /
• v.34 no.4
• /
• pp.300-304
• /
• 2019

This study was conducted to examine the oocyte recovery efficiency through having an OPU session once and twice a week. Also, the oocyte recovery efficiency was examined by using OPU after two and three months of rest period. Six cows were used for oocytes collection and were randomly divided into two groups. In experiment 1, OPU sessions were conducted once and twice a week to collect oocytes. The collected oocytes between once and twice OPU groups were classified into four groups (grade 1, 2, 3 and 4) according to the quality of cumulus cells and ooplasm. Based on the result, the percentage of collected oocytes per aspirated follicle number was similar between once and twice OPU session groups (65.5 ± 1.9 and 68.7 ± 1.4 vs.). However, the percentage of grade 1 oocytes from the twice OPU session group was significantly high compared with that of the once a week OPU session group (25.3 ± 0.9 and 32.5 ± 1.2% vs. once and twice session group, respectively, p < 0.05). In experiment 2, the group with three months of rest period tended to have a high percentage of collected oocyte compared with the group with two months of rest period (64.6 and 70.9% vs. 2 and 3 months rest group, respectively, p = 0.62). The percentage of grade 4 in the group with three months of rest period was significantly low compared with the group with two months of rest period group (27.3 and 36.5% vs. two and three months rest group, respectively, p = 0.05). In conclusion, twice a week OPU session is suitable for collection of high quality oocytes by using OPU, and three months of rest period is needed for the recovery of oocyte quality of a donor cow.

• Journal of Biosystems Engineering
• /
• v.42 no.4
• /
• pp.283-292
• /
• 2017

Purpose: Japanese Apricot, a type of plum, has various medicinal and economical applications. Plums are quite popular worldwide, but their deseeding remains a serious impediment to their processing. Therefore, a plum (Japanese Apricot) seed remover (PSR) was developed that can use various types of cutters according to the purpose of the plum processing, and its performance was evaluated. Methods: The proposed PSR, which allows multipurpose cutters, namely, zero-, two-, and four-blade cutters, to be installed, was first designed and manufactured. To identify appropriate parameters related to the cutting pressure, plums were harvested from three regions during three harvesting periods, and their geometrical and mechanical properties were measured. After application of the parameters related to the cutting pressure, a performance test was carried out on both fresh and frozen plums by identifying the ratios of the flesh recovery, seed recovery, seed breakage, deseeding efficiency, and machine efficiency. Results: The results show that, using the proper calculation of the processing parameters, 100% deseeding efficiency was facilitated regardless of the type of cutter used. However, in the case of a four-blade cutter, there are significant differences in the flesh recovery ratio according to the plum setting angle. Between the fresh and frozen plums, all cutters showed a significantly better flesh recovery ratio for the case of fresh plums. Conclusions: This machine will advance the plum processing technology, and eventually help the plum industry flourish.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.7
• /
• pp.557-564
• /
• 2009

The objective of this study is to efficiently recover phosphorus contained in sewage sludge by a struvite-forming method. The performances were evaluated under various operating conditions(elution with the kind of acid, Mg-compound and temperature) in order to reach the optimum conditions of struvite-forming. As a result, as an elution solution, the elution efficiency of $H_2SO_4$ was 2.65 times higher than that of HCl. Also, the precipitation efficiency of struvite was the highest (97.4%) in case of using $MgCl_2{\cdot}6H_2O$ as Mg-compounds at $25^{\circ}C$. However, the side reaction by Fe, Al and Zn appeared in process of phosphorus recovery. To solve some problems caused by side reacton, large quantities of co-precipitation materials produced by side reaction were removed by precipitating phosphorus compounds in pH 7. Consequently, the recovery efficiency of phosphorus by a struviteforming method was 82.99%, and purity of the recovered struvite product was high.

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.2
• /
• pp.131-143
• /
• 2018

Phosphorus (P) is a limited, essential, and irreplaceable nutrient for the biological activity of all the living organisms. Sewage sludge ash (SSA) is one of the most important secondary P resources due to its high P content. The SSA has been intensively investigated to recover P by wet chemicals (acid or alkali). Even though $H_2SO_4$ was mainly used to extract P because of its low cost and accessibility, the formation of $CaSO_4$ (gypsum) hinders its use. Heavy metals in the SSA also cause a significant problem in P recovery since fertilizer needs to meet government standards for human health. Therefore, P recovery process with selective heavy metal removal needs to be developed. In this paper some of the most advanced P recovery processes have been introduced and discussed their technical characteristics. The results showed that further research is needed to identify the chemical mechanisms of P transformation in the recovery process and to increase P recovery efficiency and the yields.

• Journal of ILASS-Korea
• /
• v.28 no.3
• /
• pp.126-133
• /
• 2023

This study analyzes the flow characteristics and sponge ball recovery performance in a ball strainer according to vortex promoter design variables through flow-particle analysis based on actual experiments to derive a method for improving the recovery rate of cleaning sponge balls of CTCS applied to existing power plants. Based on the ball strainer in CTCS used in the power plant, the experiment was conducted by changing the design factor of the improved shape. In addition, flow and particle analysis were performed under the same conditions as the experiment to numerically the flow characteristics and recovery rate in the ball strainer according to the design factor of the vortex promoter. As a result of the study, it was confirmed that the recovery performance was improved by about 3% by changing the design height of the Vortex promoter. And when comparing the difference between maximum and minimum recovery rate, it was found that the effect on the recovery performance increased slightly according to the distance condition compared to the vortex promoter design height condition.

• Journal of Wellbeing Management and Applied Psychology
• /
• v.7 no.3
• /
• pp.1-11
• /
• 2024

Purpose: The purpose of this study is to present an efficient emission reduction ratio of plastic to reduce carbon dioxide, the main cause of greenhouse gases. Research design, data and methodology: This study calculated the absolute value of carbon dioxide by setting an equation through the emission coefficient using the US EPA's WARM model. Results: In the recycling ratio of 70%, it was found that the energy recovery ratio was 15.6%, which was the energy recovery ratio without generating carbon dioxide. When carbon dioxide is generated by changing plastic waste emissions, optimal efficiency is achieved by reducing emissions by 10% to 30% of energy recovery ratio, 20% to 50% of energy recovery ratio, and 30% to 80% or more of energy recovery ratio. Conclusions: The recycling rate should be set at a minimum of 70%, so that a carbon dioxide-free energy recovery rate could be obtained during the recycling process, supporting an eco-friendly basis for environmental policies aimed at this rate. In addition, it was possible to suggest that it is essential to reduce emissions by at least 30% for eco-friendly recycling measures that can achieve both economic and environmental feasibility in the energy recovery process through incineration during recycling in Korea.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.4
• /
• pp.41-49
• /
• 2023

This study examined the effect of input substrate concentration on hydrogen production of microbial electrolysis cells. To compare the performance of MEC according to the input substrate concentration, six laboratory-scale MEC reactors were operated by sequentially increasing the input substrate concentration from 2 g/L of sodium acetate, to 4 g/L, and 6 g/L. The current density, hydrogen production, and SCOD removal rate were analyzed, and energy efficiency and cathodic hydrogen recovery were calculated to compare the performance of MEC. The maximum volumetric current density was obtained at 4 g/L condition (76.3 A/m³) and it decreased to 19.0 A/m³, when the input concentration was increased to 6 g/L, which was a 75% decrease compared to the 4 g/L input condition. Maximum hydrogen production was obtained also at 4 g/L condition (47.3 ± 16.8 mL), but maximum hydrogen yield was obtained at 2 g/L input condition (1.1 L H₂/g COD_in). Energy efficiencies were also highest in 2 g/L condition; the lowest result was observed at 6 g/L condition. Maximum electrical energy efficiency was 76.4%, and the maximum overall energy efficiency was 39.7% at 2 g/L condition. However, when the substrate concentration increased to 6 g/L, the performance was drastically decreased. Cathodic hydrogen recovery also showed a similar tendency with energy efficiency, with the lowest concentration condition showing the best performance. It can be concluded that operating at low input substrate concentration might be better when considering not only hydrogen yield but also energy efficiency.