• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1352-1354
• /
• 1997

Transparent conductive thin films have found many application in many active and passive electronic and opto-electronic devices as like flat Panel display electrode and window heat mirror, etc. Low resistivity and high transmittance of this films can be obtained by controlling deposition parameters, which are oxygen partial Pressure, substrate temperature and dopant concentration. In this study, We prepared non-stoichiometric and Sb-doped thin films of tin dioxide by reactive DC magnetron sputtering technology. The lowest resistivity of about $3.0{\times}10^{-3}\;{\Omega}cm$ and 80% transmittance in the visible light region have heed obtained at optimal deposition condition.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1411-1413
• /
• 1997

The thin film that is electrically conductive and optically transparent is called conductive transparent thin film. ITO(Indium-Tin Oxide) which is a kind of conductive transparent thin film has been widely used in solar cell, transparent electrical heater, selective optical filter, FDP(Flat Display Panel) such as LCD (Liquid Crystal Display), PDP(Plasma Display Panel) and so on. Especially in PDP, ITO films is used as a transparent electrode in order to maintain discharge and decrease consumption power through the improvement of cell structure. In this study, we prepared ITO by reactive r.f. sputtering with indium-tin(Sn wt 10%) alloy target instead of indium-tin oxide target. The ITO films deposited at low temperature $150^{\circ}C$ and 8% $O_2$ partial pressure showed about $3.6{\Omega}/{\square}$. At the end of firing, the resistance of ITO was decreased, the optical transparence was improved above 90%.

• Korean Journal of Materials Research
• /
• v.17 no.2
• /
• pp.61-67
• /
• 2007

The magnetron reactive sputtering was adopted to deposit CuO buffer layers on the polyimide surfaces for increasing the adhesion strength between Cu thin films and polyimide, varying $O_2$ gas flow rate from 1 to 5 sccm. The CuO oxide was formed through all the $O_2$ gas flow rates of 1 to 5 sccm, showing the highest value at the 3 sccm $O_2$ gas flow rate. The XPS analysis revealed that the $Cu_2O$ oxide was also formed with a significant ratio during the reactive sputtering. The adhesion strength is mainly dependent on the amount of CuO in the buffer layers, which can react with C-O-C or C-N bonds on the polyimide surfaces. The adhesion strength of the multi-layered Cu/buffer layer/polyimide specimen decreased linearly as the heating temperature increased to $300^{\circ}C$, even though there showd no significant change in the chemical state at the polyimide interface. This result is attributed to the decrease in surface roughness of deposited copper oxide on the polyimide, when it is heated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.231-231
• /
• 2013

반사방지막 코팅(Anti-reflection coating)은 태양전지(Solar cell), 발광다이오드(LED) 등의 반사율을 낮추어 효율을 증대시키기 위하여 사용되고 있다. 본 실험에서는 유리 기판 위에 실리콘 타겟을 이용한 Reactive magnetron sputtering 장비를 활용하여, 50~100 mTorr의 높은 공정 압력(High pressure)에서 Ar：O2 유량비를 변화시키며 증착하여 SiO2 반사방지막 코팅층을 형성하였다. Ellipsometer를 이용하여 SiO2 박막층의 굴절률(Refractive index)을 측정한 결과, 공정 압력과 Ar：O2 유량비에 따라 SiO2 박막이 다양한 굴절률을 가지는 것을 확인할 수 있었다. 또한, UV-Vis spectrometer를 이용하여, 190~1,100 nm 파장에서의 반사율(Reflectance)과 투과율(Transmittance)을 측정하여 비교, 분석하였다. 나아가 증착된 SiO2 반사방지막을 비정질 실리콘 박막 태양전지에 적용하여 효율 향상 효과를 실험하였다. 이를 활용하여 낮은 굴절률을 갖는 반사방지용 SiO2 코팅층을 형성하여 태양전지의 광 변환 효율을 상승 시킬 수 있고, 발광다이오드의 광 추출 효율을 증가시킬 있을 것으로 여겨진다.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.1
• /
• pp.27-31
• /
• 2013

Copper-oxide (CuO) thin films were prepared by reactive sputtering of Cu onto Si wafers and characterized using a statistical design of experiments approach. The most significant factor in controlling the electrical resistivity and deposition rate was determined to be the $O_2$ fraction. The deposited CuO thin films were characterized in terms of their physical and chemical properties, using X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), X-ray diffraction (XRD), and 4-point resistance measurements. The deposited copper thin films were characterized by XPS and XRD analyses to consist of $Cu^{2+}$. The CuO thin films of highest resistivity exhibited superior rectifying responses with regard to n-type Si wafers, with a current ratio of $3.8{\times}10^3$. These superior responses are believed to be associated with the formation of a charge-depletion region originating from the p-type CuO and n-type Si materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.393-394
• /
• 2008

$TiO_2$ is a wide band-gap semiconductor (3.4 eV) and can only absorb about 5% of sun light in the ultraviolet light region, which largely limits its practical applications because of the lower utility of sun light and quantum yield. In order to move the absorption edge of $TiO_2$ films to visible spectrum range, we have made the impurity level within a band-gap of $TiO_2$ thin film by introduction of oxygen vacancy. Oxygen-defected $TiO_2$ thin film have prepared by reactive sputtering with the partial pressure of Ar:$O_2$=10:90~99.33:0.66 ratio. As a result, we could have the impurity level of about 2.75 eV on condition that oxygen partial pressure is below 7%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.367-367
• /
• 2008

Aluminum nitride (AlN) thin films have been deposited on Si substrate by using reactive RF magnetron sputtering method in a gas mixture of Ar and $N_2$ at different $N_2$ concentration. It was found that $N_2$ concentration was varied in the range up to 20-100%, highly c-axis oriented film can be obtained at 50% $N_2$ with full width at half maximum (FWHM) $4.5^{\circ}$. Decrease in surface roughness from 7.5 nm to 4.6 nm found to be associated with decrease in grain size, with $N_2$ concentration; however, the AlN film fabricated at 20% $N_2$ exhibited a granular type of structure with non-uniform grains. The absorption peak was observed around 675 $cm^{-1}$ in fourier transform infrared spectroscopy (FTIR). It is concluded that the AlN film deposited at $N_2$ concentration of 50% exhibited the most desirable properties for the application of high-frequency surface acoustic devices.

• Journal of the Korean Magnetics Society
• /
• v.8 no.3
• /
• pp.138-143
• /
• 1998

We have investigated the magnetic properties of FeBN and FeSiN films deposited by RF magnetron reactive sputtering system. It was investigated that the compositions of B, Si and N were the main factors influencing the soft magnetic properties and film resistivity. The addition of small amount of N significantly improve the soft magnetic properties and electrical resistivity. The FeBN and FeSiN films were showed good soft magnetic properties which were Hc<1 Oe, Bs:19~19 kG and $\mu$'>1000 values. The composition of films were $Fe_{75}(BN)_{25},\;Fe_{78}(SiN)_{22}$ and resistivity was 100~120 $\mu$$\Omega$-cm. but, futher increase in B, Si and N concentration degraded the soft magnetic properties due to formation of nitride such as $Fe_4N$ compound.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.7
• /
• pp.288-292
• /
• 2003

AlM thin film has been deposited on A1$_2$O$_3$ substrate by reactive radio frequency(RF) magnetron sputtering method under various operating conditions such as working pressure, fraction of nitrogen partial pressure, and substrate temperature. Scanning Electron Microscope(SEM), X-ray Diffraction(XRD), and Atomic Force Microscope(AFM) have been measured to find out structural properties and preferred orientation of AlN thin films. SAW velocity of IDTs/AlN/Si structure was about 5038［㎧］ at the center frequency of 251.9［MHz］ and insertion loss was measured to be relatively low value of 35.6［dB］. SAW velocity of IDTs/AlN/A1$_2$O$_3$ structure was improved to be about 5960［㎧］ at the center frequency of 296.7［MHz］.

• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.525-531
• /
• 1996

(Ti1-xAlx)N films were deposited on high speed steel and silicon substrates by reactive sputtering in mixed $Ar-N_2$ discharges. Crystalline phases and microhardness of ($Ti_1_xAl_x$)N films were investigated with variation of the film composition and substrate RF bias voltage. With Al content x of about 0.6, crystalline phase of ( $Ti_1_xAl_x$N films was changed from single-phase NaCl structure to two phase mixture of NaCl and wurtzite structures: Microhardness of ($Ti_1_xAl_x$)N films was largely improved by applying RF bias voltage above 50 V during deposition. Hardness of ($Ti_1_xAl_x$)N films reached a maximum value for Al content x of about 0.4, and 1900 kg/$mm^2$ was obtained for 1$\mu m$-thick ($Ti_{0.6}Al_{0.4}$)N films.