• 접착 및 계면
• /
• 제6권4호
• /
• pp.1-6
• /
• 2005

본 실험에서는 화학적 표면처리된 탄화규소의 첨가가 탄화규소(SiC)/에폭시 복합재료의 critical strain energy release rate mode II ($G_{IIC}$) 특성에 미치는 영향에 대하여 알아보았으며, 표면처리된 SiC의 표면특성은 산 염기도와 FT-IR을 사용하여 알아보았다. 또한 복합재료의 기계적 계면물성은 $G_{IIC}$를 통하여 알아보았다. 실험결과, 산성 용액으로 표면처리한 SiC (A-SiC)의 표면 산도가 염기성(B-SiC) 또는 표면처리 하지 않은 SiC (V-SiC)보다 높으며, $G_{IIC}$의 크랙저항 특성은 A-SiC가 향상되었는데, 이러한 결과는 SiC 충전재와 에폭시 수지간의 분자간 계면결합력의 향상 때문으로 판단된다.

• 한국환경보건학회지
• /
• 제23권1호
• /
• pp.95-104
• /
• 1997

The objectives of this study are to investigate the effect of media on the removal efficiency of nitrate-nitrogen and the biofilm thickness in the fluidized bed biofilm reactor(FBBR) used for the high rate denitrification of nitric acid wastewater. Granular activated carbon(GAC) of 1.274 mm diameter and sand of 0.455 mm diameter were used as the media in the FBBR of 0.05 m diameter and 1.5 m height. As the nitrate-nitrogen concentration of the influent was increased stepwise from 600 to 4800 mg/l, the nitrate- and nitrite-nitrogen concentration of the effluent, biofilm thickness and biofilm dry density were measured to study the effects of media on the denitrification efficiency. The biofilm thickness increased with the substrate loading rate, and the biofilm dry density decreased with the increase of the biofilm thickness. At the influent nitrate-nitrogen concentration of 2400 mg/l, the removal efficiency in the FBBR with GAC was 88%, while that in the FBBR with sand was 99.6%. The biofilm in the FBBR with GAC was so thick, 754.9 $\mu$m, as to increase the mass transfer resistance, compared to that, 143.7 $\mu$m, in the FBBR with sand. The maximum specific denitrification rate in the FBBR with GAC was 15.0 kg-N/m$^3\cdot$ day, while that in the FBBR with sand was 18.0 kg-N/m$^3\cdot$ day. The biomass concentration in the FBBR with sand exhibited the high value 37 kg/m$^3$.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.352-355
• /
• 2007

Polycrystalline materials such as steels(BCC) and aluminum alloys(FCC) show the strain hardening and the strain rate hardening during the plastic deformation. The strain hardening is induced by deformation resistance of dislocation glide on some crystallographic systems and increase of the dislocation density on grain boundaries or inner grain. However, the phenomenon of the strain rate hardening is not demonstrated distinctly. In this paper, tensile tests for various strain rates are performed in the rage of $10^{-2}$ to $10^2s^{-1}$ then, specimens are extracted on the same strain position to investigate the microscopic behavior of deformed materials. The extracted specimen is investigated by using the electron backscattered diffraction(EBSD) and transmission electron microscopy(TEM) results which contain grain size, grain shape, aspect ratio and dislocation substructure.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2048-2053
• /
• 2003

The present study investigated the effect of the transversal vibration on the flow characteristics for non-Newtonian fluids. The effect was tested by experiment and numerical analysis. For Newtonian fluids, both of experiment and numerical analysis results showed that mechanical vibration did not affect the flow rate. For non-Newtonian fluids, however, there was significant disagreement between experiment and numerical results. The numerical results showed a negligibly small effect of vibration on the flow rate whereas experimental results showed a significant flow rate increase associated with transversal vibration. The results implied that the increased flow rate was caused not only by imposed shear rates at the wall but also by the changes of rheological characteristics due to the transversal vibration.

• 한국수소및신에너지학회논문집
• /
• 제33권6호
• /
• pp.803-807
• /
• 2022

In this study, the battery performance change according to the change of electrolyte flow rate. With increase of electrolyte flow rate the energy efficiency showed tendency of decrease. The electrochemical impedance spectroscopy results showed the increased resistance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.42-44
• /
• 2005

Many cellular phone volunteer studies have been conducted since such a social issue is raised that the long time usage of cellular phone may increase health risk. While there were various volunteer studies using GSM cellular phone on heart rate and blood pressure at abroad, very few studies using CDMA phone were conducted in domestic and abroad. In this study, the volunteer groups of 21 adults were exposed at 300 mW for half an hour, and the physiological parameters such as blood pressure, heart rate, respiration rate, and skin impedance were measured. All the parameters' results did not reveal any differences between exposure and non-exposure conditions in adults.

• Journal of Microbiology and Biotechnology
• /
• 제31권5호
• /
• pp.733-739
• /
• 2021

Acinetobacter strains are widely present in the environment. Some antimicrobial-resistant strains of this genus have been implicated in infections acquired in hospitals. Genetic similarities have been reported between Acinetobacter strains in nosocomial infections and those isolated from foods. However, the antimicrobial resistance of Acinetobacter strains in foods, such as meat, remains unclear. This study initially aimed to isolate Campylobacter strains; instead, strains of the genus Acinetobacter were isolated from meat products, and their antimicrobial resistance was investigated. In total, 58 Acinetobacter strains were isolated from 381 meat samples. Of these, 32 strains (38.6%) were from beef, 22 (26.5%) from pork, and 4 (4.8%) from duck meat. Antimicrobial susceptibility tests revealed that 12 strains were resistant to more than one antimicrobial agent, whereas two strains were multidrug-resistant; both strains were resistant to colistin. Cephalosporin antimicrobials showed high minimal inhibitory concentration against Acinetobacter strains. Resfinder analysis showed that one colistin-resistant strain carried mcr-4.3; this plasmid type was not confirmed, even when analyzed with PlasmidFinder. Analysis of the contig harboring mcr-4.3 using BLAST confirmed that this contig was related to mcr-4.3 of Acinetobacter baumannii. The increase in antimicrobial resistance in food production environments increases the resistance rate of Acinetobacter strains present in meat, inhibits the isolation of Campylobacter strains, and acts as a medium for the transmission of antimicrobial resistance in the environment. Therefore, further investigations are warranted to prevent the spread of antimicrobial resistance in food products.

• Corrosion Science and Technology
• /
• 제3권6호
• /
• pp.251-256
• /
• 2004

Exposure of zinc samples in simulated acid rain solution (SARS) was investigated under a periodic wet-dry conditions using an AC impedance technique. The periodic wet and dry exposure consisted of the immersion of zinc samples in SARS for one hour followed by exposure to 7 hours drying at 60% RH. Phases of the corrosion products were indentified by X-ray diffraction (XRD). The influence of relative humdiity (RH), temperature, and surface inclination on the atmospheric corrosion of zinc is described. The reciprocal of polarization resistance (1/Rp) decreases rapidly during the initial stages then slowly and eventually attains a steady state as exposure time progresses. The average of reciprocal of polarization resistance per cycle, (ARPR) was calculated and found to decrease as number of exposure cycle increases. An increase of temperature enhances the corrsion rate of zinc. The values of ARPR, of a sample inclined at 30 o are lower than those for a sample oriented horizontally. The experiment result shows a pronounced dependence of reciprocal of polarization resistance on RH. Exposure in the presence of carbonate anions gives rise to more protective corrosion products than in nitrate anion solution. The corrosion mechanism during the initial stages of atmospheric zinc corrosion under wet-dry cyclic conditions is suggested.

• Advances in concrete construction
• /
• 제16권5호
• /
• pp.269-276
• /
• 2023

In order to study the effect of rubber particle size and admixture on the frost resistance of self-compacting concrete, three self-compacting concrete specimens with equal volume replacement of fine aggregate by rubber particles of different particle sizes were prepared, while conventional self-compacting concrete was made as a comparison specimen. The degradation law of rubber aggregate self-compacted concrete under freeze-thaw cycles was investigated by fast-freezing method test. The results show that the rubber aggregate has some influence on the mechanical properties and freeze-thaw durability of the self-compacting concrete. With the increase of rubber aggregate, the compressive strength of self-compacting concrete gradually decreases, and the smaller the rubber aggregate particle size is, the smaller the effect on the compressive strength of the matrix; rubber aggregate can improve the frost resistance of self-compacting concrete, and the smaller the rubber particle size is, the more obvious the effect on the improvement of the frost resistance of the matrix under the same dosage. Through the research of this paper, it is recommended to use 60~80 purpose rubber aggregate and the substitution rate of 10% is chosen as the best effect.

• 한국표면공학회지
• /
• 제28권3호
• /
• pp.142-151
• /
• 1995

In this research, a thin layer of Cr was coated on the pure Ni and Inconel 601 by PECVD (Plasma Enhanced Chemical Vapor Deposition) in order to study the effect of Cr on the oxidation behavior at high temperature. Cr coated Inconel 601, which was oxidized at $1100^{\circ}C$ for 24 hours, formed a protective $Cr_2O_3$ oxide layer and the resistance to isothermai oxidation was improved. On the other hand, oxidation resistance of Cr coated Inconel 601 at 100$0^{\circ}C$ was not significantly improved, probably due to the formation or insufficient $Cr_2O_3$ layer. But, when oxidized at $1000^{\circ}C$ and $1100^{\circ}C$ for 100 hours, Cr coated Inconel 601 improved isothermal oxidation resistance by the formation of continuous $Cr_2O_3$ external scale and by the development of $Al_2O_3$ subscales. Cr coated Ni formed inner layer of $Cr_2O_3$ within almost pure NiO, which provided additional cation vacancies, thus increasing the mobility of Ni ions in this region. It is believed that this doping effect resulted in an increase in the observed oxidation rate compared with pure Ni and did not improve the oxidation resistance.