• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.3
• /
• pp.423-446
• /
• 1993

Titanium and its alloys are finding increasing use in medical devices and dental implants. The strong selling point of titanium is its resistance to the highly corrosive body fluids in which an implant must survive. This corrosion resistance is due to a tenacious passive oxide or film which exists on the metal's surface and renders it passive. Potentiodynamic polarization measurement is one of the most commonly used electro-chemical methods that have been applied to measure corrosion rates. And the potentiodynamic polarization test supplies detailed information such as open circuit, rupture, and passivation potential. Furthermore, it indicates the passive range and sensitivity to pitting corrosion. This study was designed to compare the corrosion resistance of the commonly used dental implant materials such as CP Ti, Ti-6A1-4V, Co-Cr-Mo alloy, and 316L stainless steel. And the effects of galvanic couples between titanium and the dental alloys were assessed for their useful-ness-as. materials for superstructure. The working electrode is the specimen , the reference electrode is a saturated calomel electrode (SCE), and the counter electrode is made of carbon. In $N_2-saturated$ 0.9% NaCl solutions, the potential scanning was performed starting from -800mV (SCE) and the scan rate was 1 mV/sec. At least three different polarization measurements were carried out for each material on separate specimen. The galvanic corrosion measurements were conducted in the zero-shunt ammeter with an implant supraconstruction surface ratio of 1:1. The contact current density was recorded over a 24-hour period. The results were as follows : 1. In potential-time curve, all specimens became increasingly more noble after immersion in the test solution and reached between -70mV and 50mV (SCE) respectively after 12 hours. 2. The Ti and Ti alloy in the saline solution were most resistant to corrosion. They showed the typical passive behavior which was exhibited over the entire experimental range. Therefore no breakdown potentials were observed. 3. Comparing the rupture potentials, Ti and Ti alloy had the high(:st value (because their break-down potentials were not observed in this study potential range ) followed by Co-Cr-Mo alloy and stainless steel (316L). So , the corrosion resistance of titanium was cecellent, Co-Cr-Mo alloy slightly inferior and stainless steel (316L) much less. 4. The contact current density sinks faster than any other galvanic couple in the case of Ti/gold alloy. 5. Ag-Pd alloy coupled with Ti yielded high current density in the early stage. Furthermore, Ti became anodic. 6. Ti/Ni-Cr alloy showed a relatively high galvanic current and a tendency to increase.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.318-325
• /
• 2023

The detection of antibiotics in treated wastewater is a global concern as it enters water bodies and causes the development of antibiotic resistance genes in humans and marine life. The study specifically aims to explore the potential of ferrate (VI) in eliminating tetracycline (TCL). The degradation of TCL is optimized with parametric studies, viz., the effect of pH and concentration, which provide insights into TCL elimination. The increase in pH (from 7.0 to 10.0) favors the percentage removal of TCL; however, the increase in TCL concentrations from 0.02 to 0.3 mmol/L caused a decrease in percentage TCL removal from 97.4 to 29.1%, respectively, at pH 10.0. The time-dependent elimination of TCL using ferrate (VI) followed pseudosecond-order rate kinetics, and an apparent rate constant (kapp) was found at 1978.8 L² /mol² /min. Coexisting ions, i.e., NaNO₃, Na₂HPO₄, NaCl, and oxalic acid, negligibly affect the oxidation of TCL by ferrate (VI). However, EDTA and glycine significantly inhibited the elimination of TCL using ferrate (VI). The mineralization of TCL using ferrate (VI) was favored at higher pH, and it increased from 18.57 to 32.52% when the solution pH increased from pH 7.0 to 10.0. Additionally, the real water samples containing a relatively high level of inorganic carbon spiked with TCL revealed that ferrate (VI) performance in the removal of TCL was unaffected, which further inferred the potential of ferrate (VI) in real implications.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.4
• /
• pp.551-561
• /
• 1998

This paper was studied to understand the characteristics of heat transfer coefficients and surface temperature distributions around a circular combustion chamber within the heat-intercept duct of kerosene fan heater. The experiment was carried out in the heat-intercept duct of kerosene fan heater attached to the blow-down-type subsonic wind tunnel with a test section of 240 mm * 240 mm * 1200 mm. The purpose of this paper was to obtain the basic data related with normal combustion for new design from conventional kerosene fan heater, and to investigate the effect of surface temperature, local and mean heat transfer coefficients versus flow-rate of convection axial fan according to the variations of heat release conditions from kerosene fan heater during normal combustion. Consequently it was found that (i) the revolution of convection axial fan during combustion had a smaller value than that of non-combustion because of the thermal resistance due to the high temperature in the heat-intercept duct, (ii) the pressure ratio P$_{2}$/P$_{1}$ had a comparatively constant value of 0.844 according to the revolution increase of turbo fan and the heating performance of kerosene fan heater had a range of 1,494 ~ 3,852 kcal/hr, (iii) the local heat transfer coefficient around a circular combustion chamber had a comparatively larger scale in the range of 315 deg. < .theta. < 45 deg. than that in the range of 90 deg. < .theta. < 270 deg. as a result of heat transfer difference between front and back of a circular combustion chamber, and (iv) the mean heat transfer coefficient around a circular combustion chamber increased linearly like a H$_{m}$=95.196Q+104.019 in condition of high heat release according to the increase of flow-rate of axial fan.n.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.556-563
• /
• 1999

The corrosion behavior of heat-resistant alloys, More 1 and Super 22H in molten salts of LiCl and $LiCl-Li_2$O was investigated in the temperature range of $650~850^{\circ}C$. In a molten salt of LiCl, a dense protective oxide scale of $LiCrO_2$ was formed, following growth of oxide scale with parabolic kinetics. But in a mixed molten salt of LiCl, a dense protective oxide scale of $LiCrO_2$ was formed, following growth of oxide scale with parabolic kinetics. But in a mixed molten salt of $LiCl-Li_2$O, a porous non-protective scale of Li\ulcorner(Cr, Ni, Fe)\ulcornerO$_2$was formed, following growth of oxide scale with linear kinetics. The corrosion rate increased slowly with the increase of temperature up to $750^{\circ}C$, but above $750^{\circ}C$ rapid increase in corrosion rate observed. The corrosion behavior of Super 22H alloy was similar to that of More 1 alloy, but Super 22H showed higher corrosion resistance than More 1.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.281-286
• /
• 2000

To analyze the shape of the net mouth of bottom trawl which is composed with 6 seams net, the field experiment was carried out on the sea near Kokunsan Is, Western sea of Korea. The distance of otter board, net height, trawl speed and resistance of the fishing gear were respectively measured according to the change of warp length and towing speed. The results obtained are summarized as follows : 1. The spreading distance of the otter board has been increased straightly according to the increment of towing speed and warp length. The rate of increase by the warp length has been greatly higher than the rate of increase by the towing speed. The total variation of the spreading distance was 57.0-82.8m, and it was occupied 43-62% of the hand rope, net pendent and the length of nets. 2. The height of net mouth has been decreased straightly according to the increment of towing speed and warp length. The rate of decrease by the towing speed has been greatly higher than the decrease rate of the warp length. The total variation of the net height was 3.1-4.0m. 3. When the distance of wing tip is increased, the height of net mouth is decreased, but the ratio of the decreasing rate of the height of net mouth for the increasing rate of the distance of wing tip was gradually low according to the increment of warp length. 4. The ratio of the distance of both wing tip for the height of net mouth has been increased gradually according to the increment of towing speed and warp length, and the total variation of the ratio was 4.17-7.81 times.

• Journal of Chest Surgery
• /
• v.16 no.2
• /
• pp.199-212
• /
• 1983

The inhibition/influences of adenine compounds on the heart have been described repeatedly by many investigators, since the first report by Druny and Szent-Gyorgyi [1929]. These studies have shown that adenosine and adenine nucleotides have an over-all effect similar to that of acetylcholine [ACh] by slowing and weakening the heartbeat. The basic cellular and membrane events underlying the inhibitory action of adenosine on sinus rate, however, are not well understood. Furthermore, the physiological role of adenosine in regulation of the heartbeat remains still to be elucidated. Therefore, this study was undertaken in order to examine the response of rabbit SA node to adenosine and to compare the response to that of ACh. Isolated SA node preparation, whole atrial pair, or left atrlal strip was used in each experiment. Action potentials of SA node were recorded through the intracellular glass microelectrodes, which were filled with 3M KCI and had resistance of 30-50 M. All experiments were performed in a bicarbonate-buffered Tyrode solution which was aerated with 3% $CO_2-97%$ $O_2$ gas mixture and kept at $35^{\circ}C$. Spontaneous firing rate of SA node at 35C [Mean + SEM, n=16] was 154 + 3.3 beats/min. The parameters of action potentials were: maximum astolic potential [MDP], -731.7mV: overshoot [OS], 9 + 1.4mV; slope of pacemaker potential [SPP], 94 3.0mV/sec.Adenosine suppressed the firing rate of SA node in a dose dependent manner. This inhibitory effect appeared at the concentration of $10^{-6}M$ and was potentiated in parallel with the increase in adenosine concentration. Changes in action potential by adenosine were dose-dependent increase of MDP and decrease of SPP until $10^{-4}$. Above this concentration, however, the amplitude of action potential decreased markedly due to the simultaneous decrease of both MDP and OS. All these effects of adenosine were not affected by pretreatment of atropine [2mg/l] and propranolol [$5{\times}10^{-6}M$]. ACh [$10^{-6}M$] responses on action potential were similar to those of adenosine by increasing MDP and decreasing SPP. These effects of ACh disappeared by pretreatment of atropine [2mg/1]. Inhibition/effects of adenosine and ACh on sinus rate were enhanced synergistically with the simultaneous administration of adenosine and ACh. Marked decrease of overshoot potential was the most prominent feature on action potential. Dipyridamole [DPM], which is known to block the adenosine transport across cell membrane, definitely potentiated the action of adenosine . Adenosine suppressed the sinus rate and atrial contractility in the same dosage range, even in the reserpinized preparation. Above` results suggest that adenosine suppresses pacemaker activity, like ACh, by acting directly on the membrane of SA node, increasing MDP and decreasing SPP.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.05a
• /
• pp.83-86
• /
• 2008

The concrete used most in construction materials. There is an overcrowded iron dimensions use of the concrete at time of the other concrete theory on the reinforcing rod back which did congestion and compares it with this, and there are more few dimensions of the aggregate than concrete, and quantity of aggregate passage is superior in mortar than concrete. If a volume rate of the aggregate writes mortar than concrete against this, therefore, unit amount increases, and quantity of paste increases and quantity of dry shrinkage than increase concrete. However, I let I regulate lay priest distribution of the aggregate, and the results rates increase and reduce unit amount and decrease quantity of dry shrinkage, and separation resistance and the gap passage characteristics are judged because it can be it in a substitute document of very superior concrete. I came to carry out the study that I watched to let I was useful a little more and do the improvement repair of a become building wall body, a basement pillar and repair reinforcement of the assistant in the reinforcing rod back, the old age when I made congestion here. I regulated lay priest distribution of the aggregate in the study and regulated substitution rate of the aggregate (40%, 50%, 60%) and divided W/C 30%, 40% standards and produced mortar and I compared quantity of air by this, slump, compression robbery and showed it this time.

• Korean journal of applied entomology
• /
• v.9 no.1
• /
• pp.15-20
• /
• 1970

An investigation was carried out to know the relationship between resistance of rice varieties to blast disease and the chemical components, especially total nitrogen and total sugars, in the rice plants. The results sic summarized as follow: 1) The nitrogen contents in the resistant variety were less than those of susceptible one, and sugar contents were reversed. Accordingly, the C/N ratio in the resistant variety was higher than that obtained by susceptible one. 2) The free amino acids contents, especially, Glutamine, Valine, Leusine and Iso-leusine, in the resistant varieties were more than those of the susceptible varieties. 3) The starch synthetic activity of rice leaves in the resistant varieties was higher than that of susceptible one in fructose and glucose solutions, but it was reversed in sucrose solution. 4) When more nitrogen was dressed, the total nitrogen content of rice leaves was increased than the ordinary dressing. The rate of increase in nitrogen content in resistant variety was lower than those of the susceptible. The total sugar content of rice plants dressed more nitrogen was decreased at early tillering stage, but increased at maximum tillering stage. It seemed that the rate of increase of total sugar in the resistant variety was higher than those of the susceptible.

• Applied Chemistry for Engineering
• /
• v.9 no.4
• /
• pp.475-480
• /
• 1998

A study on the electrochemical reduction of uranium (VI) to uranium (IV) was carried out in the mixed phases of an organic phase with uranium (VI) and aqueous phase of nitric acid by use of a highly packed glassy carbon (GC) fiber column electrode system, and a model for in-situ electrolytic stripping of uranium (VI) was suggested. The electrochemical reduction of uranium (VI) occurred faster in organic phase than in aqueous phase of the mixed phases. The uranium stripping yield increased and then became constant with the increase of organic flow rate of the electrolytic system due to the increase of diffusion resistance of uranium ions in the organic phase into the aqueous phase. Aqueous flow rate, on the other hand, didn't affect the total uranium (VI) reduction current in the system. The system combined with electrochemical reduction was confirmed to be much more effective than the simple system without it in stripping uranium.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1491-1493
• /
• 2000

Continuing improvement of microprocessor performance involves in the device size. This allow greater device speed, an increase in device packing density, and an increase in the number of functions that can reside on a single chip. However this has led to propagation delay, crosstalk noise, and power dissipation due to resistance-capacitance(RC) coupling become significant due to increased wiring capacitance, especially interline capacitance between the metal lines on the same metal level. So, MSSQ which has the permittivity between 2.5-3.2 is used to prevent from these problems. For pattering MSSQ(Methylsilsequioxane), we use RIE(Reactive Ion Etching) and MERIE(Magnetically enhanced Reactive Ion Etching) which could provide good anisotropic etching. In this study, we optimized the flow rate of $CF_{4}/O_2$ gas, RF power to obtain the best etching rate and roughness and also analyzed the etching result using $\alpha$-step profilemeter, SEM, infrared spectrum and AFM.