• KSTLE International Journal
• /
• v.3 no.1
• /
• pp.49-53
• /
• 2002

Inconel 690 for nuclear steam generator tube has more chromium than the conventionally used Inconel 600 in order to increase the corrosion resistance. TD evaluate the tribological characteristics under fretting condition the fretting tests as well as sliding tests were carried out in elevated temperature water environment. Fretting tests of the cross-cylinder type were done under various vibrating amplitudes and applied normal loads in order to measure the friction forces and wear volumes. Also, the conventional sliding tests of pin-en-disk type were carried out to compare the test results. In fretting, the friction was very sensitive to the load and the amplitude. The friction coefficient decreased with increasing load and decreasing amplitude. Also, the wear of Inconel 690 can be predictable using the work rate model. Depending on normal loads and vibrating amplitudes, distinctively different wear mechanisms and of ten drastically different wear rates can occur. It was fecund that the fretting wear coefficients in water were increased as increasing the temperature of water.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.257-260
• /
• 2004

The durability and water - resisting capability of nuclear concrete structures can be greatly improved as the density of concrete surface increases. Applying the surface penetration sealer to the concrete surface can increase the surface density. Therefore, the objective of this study is to identify the most suitable surface penetration sealer based on lab test. The considered parameters rate and water resistance and absorbance rate of the concrete specimen after the penetration sealer are applied. The experimental study resulted in the identification of the two most suitable surface penetration sealer based on their performance.

• Environmental Engineering Research
• /
• v.11 no.2
• /
• pp.91-98
• /
• 2006

There is a possibility of the production of the air bubbles in membrane pores due to the reduction in pressure during membrane filtration. The effect of fine air bubbles from dissolved gases on microfiltration was investigated in the submerged membrane bio-reactor (SMBR). The $R_{air}$ (air bubble resistance) was defined as the filtration resistance due to the air bubbles formed from the gasification of dissolved gases. From the results of filtration tests using pure water with changes in the dissolved oxygen concentration, the air bubbles from dissolved gases were confirmed to act as a foulant and; thus, increase the filtration resistance. The standard pore blocking and cake filtration models, SPBM and CFM, respectively, were applied to investigate the mechanism of air bubble fouling on a hollow fiber membrane. However, the application of the SPBM and CFM were limited in explaining the mechanism due to the properties of air bubble. With a simple comparison of the different filtration resistances, the $R_{air}$ portion was below 1% of the total filtration resistance during sludge filtration. Therefore, the air bubbles from dissolved gases would only be a minor foulant in the SMBR. However, under the conditions of a high gasification rate from dissolved gases, the effect of air bubble fouling should be considered in microfiltration.

• Korean Journal of Veterinary Research
• /
• v.39 no.2
• /
• pp.343-352
• /
• 1999

Vancomycin resistant enterococci (VRE) have emerged as an important nosocomial pathogen. Since 1989 the Center for Disease Control, United States, has reported a rapid increase in the incidence of enterococcal bacteremia and endocarditis infection by VRE. It was suggested that the use of avoparcin was associated with the appearance of VRE in animal husbandry. To date, several detection methods have been used based on conventional methods of culture and gene detection. However, these methods have some limitations such as time-consuming, laborious and additional differential needs. Therefore, In this study a multiplex PCR method was established to detect and differentiate resistance types of enterococci which specifically amplify the four van genes encoding vancomycin resistance elements. Using the method, we investigated the incidence rates and types of VRE from farms using or not using avoparcin. A total of 1091 animal fecal samples were collected from 70 pig and 32 poultry farms. A total of 425 of enterococci were isolated from samples. Of the 425 isolates, 11 of the them showed a pattern of high-level vancomycin resistance (MIC : $64{\sim}256{\mu}g/ml$) which was associated with the presence of the vanA or vanB gene. Fifty-seven isolates showed a pattern of low-level vancomycin resistance (MIC : $3{\sim}8{\mu}g/ml$) associated with the vanC-1 or vanC-2 gene. Interestingly, all isolates with high-level vancomycin resistance were from farms that have never used avoparcin. Moreover, the high-level VRE isolation rate in Korea (2.58%) was much lower than that of other countries (50% in England, 7% in Belgium) where avoparcin have been used. In conclusion, the multiplex PCR method established in this study could be applied for detection of VRE.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.238-247
• /
• 2021

PEO (plasma electrolytic oxidation) was applied to modify the surface of AZ31 magnesium alloy in this study. The mixed solution of sodium hydroxide (NaOH) and sodium silicate (Na₂SiO₃) was used as the electrolyte, and 0 - 0.05 g/L of Ca-GP (Glycerol Phosphate Calcium salt) was added in the electrolyte as an additive. PEO treatment was conducted at a current density of 30mA/cm² for 5 minutes using a DC power supply. The surface properties were identified by SEM, XRD and surface roughness analyses, and the corrosion resistance was evaluated by potentiodynamic polarization and immersion tests. In addition, the biocompatibility was evaluated by immersion test in SBF solution. As the concentration of Ca-GP was increased, the surface morphology was denser and more uniform, and the amount of Ca and the thickness of oxide layer increased. Only Mg peak was observed in XRD analysis due to very thin oxide layer. The corrosion resistance of PEO-treated samples increased with the concentration of Ca-GP in comparision with the untreated sample. In particular, the highest corrosion resistance was identified at the group of 0.04g Ca-GP through potentiodynamic polarization and immersion tests in saline solution (0.9 wt.%NaCl). During the immersion in saline solution, pH rapidly increased at the beginning of immersion period due to rapid corrosion, and then increase rate of pH decreased. However, the pH value in the SBF temporarily increased from 7.4 to 8.5 during the day, then decreased due to the inhibition of corrosion with HA(hydroxyapatite) formation.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.187-193
• /
• 2010

Chromium nitride (CrN) samples with two different layer structures (multilayer and single layer) were coated on bipolar plates of polymer electrolyte membrane fuel cells (PEMFC) using the reactive sputtering method. The effects with respect to layer structure on corrosion resistance and overall cell performance were investigated. A continuous and thin chromium nitride layer ($Cr_{0.48}\;N_{0.52}$) was formed on the surface of the SUS 316L when the nitrogen flow rate was 10 sccm. The electrochemical stability of the coated layers was examined using the potentiodynamic and potentiostatic methods in the simulated corrosive circumstances of the PEMFC under $80^{\circ}C$. Interfacial contact resistance (ICR) between the CrN coated sample and the gas diffusion layer was measured by using Wang's method. A single cell performance test was also conducted. The test results showed that CrN coated SUS316L with multilayer structure had excellent corrosion resistance compared to single layer structures and single cell performance results with $25\;cm^2$ in effective area also showed the same tendency. The difference of the electrochemical properties between the single and multilayer samples was attributed to the Cr interlayer layer, which improved the corrosion resistance. Because the coating layer was damaged by pinholes, the Cr layer prevented the penetration of corrosive media into the substrate. Therefore, the CrN with a multilayer structure is an effective coating method to increase the corrosion resistance and to decrease the ICR for metallic bipolar plates in PEMFC.

• Journal of Korean Physical Therapy Science
• /
• v.27 no.3
• /
• pp.1-11
• /
• 2020

Background: The purpose of this study was to investigated the effects of threshold resistance inspiratory muscle training on respiratory function in chronic stroke patients. Design: Randomized Controlled Trial Methods: Eighteen patient with stroke were randomly assigned to the experimental group (n=9) and control group (n=9) all testing and training. The experimental group underwent threshold resistance inspiratory muscle training with resistance adjusted of maximal inspiratory pressure, 60 breathing a day and general physical therapy 30 minutes a day, 5 times a week for 4 weeks. The control group was taken general respiratory muscle training and general physical therapy for 4 weeks in the same way. Respiratory function, walking ability were evaluated before and after the intervention. Statistical significance of the results were evaluated by ANCOVA between control group and experimental group after intervention. Results: There was a significant increase in FVC and FEV1 in the experimental group in pulmonary function tests (p<0.05). There was a significant difference with the maximum inspiratory pressure and the maximum inspiratory flow rate between experimental and control group (p<0.05). There was no significant difference with the maximum inspiratory capacity between experimental and control group (p>0.05) but the maximum inspiratory capacity of experimental group some increased than that of control group. Conclusion: These finding gave some indications that the threshold resistance inspiratory training may benefit on pulmonary function in people with stroke, and it is feasible to be included in rehabilitation interventions with this population.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.3
• /
• pp.31-39
• /
• 2021

In this study, the fiber blending ratio and strain rate effect on the tensile properties synergy effect of hybrid fiber reinforced cement composite was evaluated. Hooked steel fiber(HSF) and smooth steel fiber(SSF) were used for reinforcing fiber. The fiber blending ratio of HSF+SSF were 1.5+0.5, 1.0+1.0 and 0.5+1.5vol.%. As a results, in the cement composite(HSF2.0) reinforced with HSF, as the strain rate increases, the tensile stress sharply decreased after the peak stress because of the decrease in the number of straightened pull-out fibers by increase of micro cracks in the matrix around HSF. When 0.5 vol.% of SSF was mixed, the micro cracks was effectively controlled at the static rate, but it was not effective in controlling micro cracks and improving the pull-out resistance of HSF at the high rate. On the other hand, the specimen(HSF1.0SSF1.0) in which 1.0vol.% HSF and 1.0vol.% SSF were mixed, each fibers controls against micro and macro cracks, and SSF improves the pull-out resistance of HSF effectively. Thus, the fiber blending effect of the strain capacity and energy absorption capacity was significantly increased at the high rate, and it showed the highest dynamic increase factor of the tensile strength, strain capacity and peak toughness. On the other hand, the incorporation of 1.5 vol.% SSF increases the number of fibers in the matrix and improves the pull-out resistance of HSF, resulting in the highest fiber blending effect of tensile strength and softening toughness. But as a low volume fraction of HSF which controlling macro crack, it was not effective for synergy of strain capacity and peak toughness.

• Journal of Korea Foundry Society
• /
• v.20 no.5
• /
• pp.323-329
• /
• 2000

The HSS consists of hard carbide and matrix of martensite, and so its characteristics of wear resistance, fracture resistance, and surface roughness are good. This study was undertaken to investigate the influence of Nb and V and manufacturing conditions on microstructural behaviors and characteristics in the HSS cylindrical specimens(90 $mm^{O.D.}$ ${\times}$ 60 $mm^{I.D.}$ ${\times}$ 50 $mm^H$) manufactured using VCC(Vertical Centrifugal Casting). In the specimen of Fe-2C-6Cr-1.5W-3Mo-4V alloy, the amount of MC carbide was increased and $M_7C_3$ carbide was decreased with the increase of V and Nb contents. The primary VC carbide was formed and followed by the rod-type eutectic MC carbide was formed in the cell boundary in 9%V added specimen. MC carbide was increased, and $M_7C_3$ carbide was decreased with the addition of Nb content. In the specimen containing more than 3%Nb, primary NbC carbide was formed within the cell of matrix. With increase in rpm, cell and carbides became fine, and amount of carbide $M_7C_3$ was decreased due to increase in cooling rate.

• Journal of Biosystems Engineering
• /
• v.29 no.2
• /
• pp.121-130
• /
• 2004

This study was carried out to develop a miller to produce white embryo rice with functional nutrients by improving the conventional vertical miller. The effects of rice moisture content and the shaft revolution speed of the miller on germ(embryo) adherence rate, whiteness, broken rice rate, and cracked rice rate were investigated. Also, the effect of the mesh size of emery stones on the germ adherence rate was investigated. The vertical prototype miller was improved with the increasement of about 42% in producing white embryo rice at proper conditions(shaft revolution speed of 900 rpm, emery stones of mesh ＃50, processing capacity of 2.3t/h, zero outlet resistance, rice moisture content of 16.2%). The results were as follows: 1. The germ adherence rate of white rice was significantly influenced by the moisture content of brown rice. The germ adherence rate of white rice decreased rapidly with the increase of the moisture content of brown rice. When brown rice with moisture content of 13.2%, 14.5%, 15.2%, 15.4% was milled by the prototype with emery stones of mesh ＃35 and shaft speed of 900(1,100) rpm, rpm adherence rate of milled rice was 76.2%(70%), 69.2%(66%), 45.9(38%), 13.0(9%), respectively. 2. The whiteness of white rice milled by the prototype with emery stones of mesh ＃35 and shaft speed of 1,100(900)rpm increased from 27(23) to about 40, respectively, as the moisture content of brown rice increased from 13.2% to 17.2%. 3. The rate of broken rice of white rice milled at 900rpm decreased by 0.6∼1.0% compared with that at 1,100rpm when the moisture content of brown rice was less than 15.2%. 4. The germ adherence rate was increased by 10.3% and 11.0%, respectively when brown rice with moisture content of 16.2% and 15.5% was milled by the prototype miller with shaft speed of 900rpm and emery stones of mesh ＃50 instead of mesh ＃35. 5. Considering the germ adherence rate, broken rice rate, and whiteness of milled rice, the proper milling conditions of the prototype miller for producing embryo rice were the moisture content of about 15%, the processing capacity of 2.3t/h and minimum outlet resistance of 0Nㆍm with shaft speed of 900rpm and emery stones of mesh ＃50.