• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.204-209
• /
• 2003

Recently, The TCN(Train Communication Network} as the distributed control systems for electric vehicles, which is the international standard of the intra vehicle communication, actively recognizes variations and supports reconfiguration of the train network when a vehicle is separated or recombined. The technique of reconfiguration to take variety and interoperability of a vehicle constitution is used when the vehicle constitution is changed. At the time, each node making up vehicle network shares the information about the variation of vehicle constitutions and the state of nodes. In the hierarchical TCN structure, an exchange of data becomes available as a work to transmit information between components is performed at the node playing a role of gateway. This paper proposes a protocol to transmit the information of the train reconfiguration. The protocol gives an application to renew a list for transmitting information and to perform the transmission that can guarantee periodic and non-periodic data transmission between nodes when the network nodes changed by a variation of the network state are reconfigured. If use this protocol, can use functions that are offered in the electric railcar at the same time that composition of vehicles is completed without delay. And when driver of the electric railcar inspect before running of vehicles, can confirm state of vehicles visually through monitor in driver's room.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1347-1350
• /
• 2005

Recently, as the road capacity reaches a limit and environmental problems become serious, there exists a gradual increasing need for railway vehicles that are environment-friendly, punctual, reliable and safe. Accordingly, in addition to conventional railroad vehicles, lots of vehicles are being newly developed. Using the developed installed measurement system, the performance characteristics of railway vehicle could be monitored precisely. After recording the input real time data of each signal from railway vehicle to the network line, we could acquire the needed information through post processing program. We could verify the running performances of railway vehicle using this system. As a result, many latent defects have been found and corrected in the prototype train. The measurement systems have contributed to dramatic reduction of the developing period.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.882-887
• /
• 2014

In this paper, the water cooling method among the forced coolant cooling methods is considered to be applied to the 110kW-class IPMSM for railway vehicles. First, basic thermal property analysis of the IPMSM is conducted using the three-dimensional thermal equivalent network method. Then, based on the results of the basic thermal property analysis, some design requirements for the water cooling jacket are deduced and a basic design of the water cooling jacket is carried out. Finally, thermal equivalent circuit of the water cooling jacket is attached to the IPMSM's 3D thermal equivalent network and then, the basic thermal and effectiveness analysis are conducted for the case of applying the water cooling jacket to the IPMSM. In the future, the thermal variation trends inside the IPMSM by the application of the water cooling jacket is expected to be quickly and easily predicted even at the design step of the railway traction motor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.529-533
• /
• 2008

Recently in Korea, noise is one of the most important social issues because the living standard becomes more higher. Railway noise is also annoying one in our society, although railway has very positive role in our country. The major measures for mitigation of railway noise in Korea are rail welding and installation of noise barrier on the noisy area. But these measures have its own limit for the calm and comfortable living environment. In Europe the railway noise problem has been treated more systematically and aggressively, there has been emission noise standard for Trans-European rail network. In this paper, the trend of noise standard for railway vehicles will be reported and the check point for our country will be discussed.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.2
• /
• pp.10-16
• /
• 2016

For higher reliability against a link failure of a control network in railway vehicles, a recovery mechanism is needed. We introduce a problem that, when a link failure occurs in a ring-topology control network, a node may experience a significant increase of transmission delay depending on its relative position within the network. We then propose two mechanisms to solve this problem: (1) differentiating and prioritizing node traffic in forwarding; and (2) switching some nodes to a backup bus-topology network. Our simulation study shows that, while the first mechanism achieves a limited gain by only compensating queuing delay, the second one gets a sufficient gain which is impacted by the number of nodes switched to the bus network.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.478-485
• /
• 2017

Urban DC railways have played an important role in urban transportation, and railway operation and energy management have been emphasized to be important to achieve maximum efficiency from existing infrastructure. Fast, accurate DC railway power flow analysis is required to operate a DC railway efficiently, and this paper proposes a novel methodology to analyze the DC railway power network by implementing the participation factor (PF). The PF concept consists of a correlation between the vehicle and the substation, as explained using zones based on the position of the vehicles running on the route. Then, the DC railway powerflow is calculated using the PF concept. Finally, the usability of the proposed method was validated via case studies with actual railway operation data, and we discuss some of the advantages of the suggested methodology.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.10
• /
• pp.1475-1480
• /
• 2013

In this paper, the basic design study of a water-cooling jacket, which have reported no cases for applying to railway traction motors so far, were conducted for applying to Interior Permanent Magnet Synchronous Motor (IPMSM) for railway vehicles. The basic thermal characteristics analysis of the 110kW-class IPMSM was performed by using 3-dimentional thermal equivalent network method. The necessary design requirements of the water-cooling jacket were derived by analyzing the results of the basic thermal properties. Next, the thermal characteristics analysis technique was established by using the equivalent model of the solenoid-typed pipe to be installed on the inside of the water-cooling jacket for 110kW-class IPMSM. Finally, a design model of 6kW-class water-cooling jacket was derived through the analysis of various design parameters.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1253-1258
• /
• 2004

A general idea of implementing and managing real-time control on the VDN for rail transit vehicles is presented. In particular, the virtual device network considered in this paper is composed of Ethernet as the data network and LonWorks network as the device (control) network. A LonWorks/IP web server was used as a gateway to realize peer to peer data communication on the virtual device networks. Experimental results are given to validate the suggested architecture.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2015-2020
• /
• 2008

Real-time communication network is important for KTX high speed train system because small problem can make a huge accident. Communication network for KTX high speed train system consists of IEEE 802.4 token bus network and FM0 encoding. The network device is developed by using MC68824 TBC, MC68185 TPM and MC68020 MPU. The network device make available to analysis of the network protocol among vehicles for Kyung-Boo high-speed train system.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.344-351
• /
• 2000

Recently, the microprocessor with network function based-controlled systems instead of conventional microprocessors is widely used to industrial applications, and also those technologies are widely adopted for train control and monitoring in modern rapid transit systems such as railway vehicles. The purpose of this paper is to propose a high quality data transmission line of railway vehicle system controlled by a microprocessor, which was designed and realized through SMG 7＆8 and ISA project. Noise, distortion and attenuation are always present in data transmission system and strictly limit performance. This paper describes a method to calculate the propagation constant, attenuation constant, phase velocity and length of stub.