• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1955-1962
• /
• 1992

The purpose of this study is to identify the radiative heat transfer augmentation by a coaxial cylinder introduced in the infinite cylindrical pipe enclosing a participating gas. The gas is either a mixture of water vapor and carbon dioxide or gray. The gas is assumed to be homogeneous at a constant temperature, and has a refractive index of unity. All of the surfaces are opaque and gray, diffusely emitting and reflecting at a constant temperature, The effect of system diameter, diameter ratio, wall emittances, gas and surface temperatures, mixture component on heat transfer augmentation are studied by using the zone method with participating gas radiative properties evaluated from the weighted sum of gray gases model. From the radiative equilibrium condition, the installed wall temperature is formulated and calculated by the iteration method. If the medium is a gray gas, the augmentation observed are negligible. For the range of values studied for a real gas, if the system diameter is larger than about 0.1m the augmentation parameter increases up to about 1.2 as the system diameter increases. The augmentation parameter have a maximum value at a certain diameter ratio. The augmentation parameters decreases as the emittance of the installed wall decreases. If the gas temperature is higher than about 1273 k, the augmentation parameter decreases as the gas temperature increases.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.1
• /
• pp.61-72
• /
• 2002

The flaring system of FPSO burns out the byproduct natural gas. The thermal loading due to radiative heat of flaring gas leads to undesirable thermal-stresses on itself. Nowadays it needs to understand the amount of thermal loading of flaring system since the requirement for the safety of the flaring system. However, few studies have been performed on the thermal environment and radiative heat flux on the FPSO flaring system. Present study suggests a procedure to model the thermal environment and a FEA process to analyze the temperature distribution and thermal stresses of FPSO flaring system. In order to get the temperature distribution, the radiative heat conditions and convective heat conditions are included in the heat transfer analysis. By making the use of temperature obtained through heat transfer analysis, the thermal stress analyses are performed. The results of the present study can be used to design the flaring system and determine the heat shield in the flaring system.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.49-53
• /
• 2001

A conventional flame type gas combustion major portion of heat is transferred to the body by convection due to small radiant ability of the gas flame. Increasing the radiation component of heat flux in the combustion zone allows to augment the efficiency of gas utilization. Such effect can be reached by using radiative gas burner applied to metal mesh combustion. Basically the gas radiant burner consists of metallic mesh of high heat resisting steels. In terms of this regards, we have made the burner consisted of metal mesh and measured the radiative flame stability of natural gas/air mixture on the metal mesh burner. The pressure loss through the metal mesh is defined by pressure-velocity slope. The more increased the pressure-velocity slope of the metal mesh is, the wider the stable zone of radiave flame on the metal mesh burner is. And the augmentation of mixture flowrate through the metal mesh make narrow the permissible range of equivalence ratio.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.3 no.1
• /
• pp.41-56
• /
• 1999

Since UV-B radiation measuring networks have not been established, numerical models which calculate the flux from other readily available meteorological measurements may play an important role. That is, such a problem can be solved by using parameterization models such as two stream approximation, the delta-Eddington method, doubling method, and discrete ordinate method. However, most UV-B radiative transfer models have not been validated with measurements, because such models are not intended as practical computational schemes for providing surface estimates of UV-B radiation. The main concern so far has been to demonstrate model sensitivity for cloudless skies. In particular, few have been concerned with real cloud information. Clouds and aerosols have generally been incorporated as constituents of particular atmospheric layers with specified optical depths and scattering properties. The parameterization model presented here is a combination of a detailed radiative transfer algorithm for a coludless sky radiative process and a more approximate scheme to handle cloud effects. The model input data requires a daily measurement of the total ozone amount plus a daily record of the amount and type of cloud in the atmosphere. Measurements for an examination of the models at the Department of Atmospheric Sciences, Pusan National University have been takenfrom February, 1995. These models can be used to calculate present and future fluxes where measurements have not been taken, and construct climatologies for the period before ozone depletion began.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1370-1375
• /
• 2004

This article investigates the heat transfer characteristics in a RTA system for LCD manufacturing and suggests a way to evaluate the quality of a poly-Si film from the thin film optics analysis. The transient and one-dimensional conductive/radiative heat transfer equation considering wave interference effect is solved to predict surface temperatures of thin films. In dealing with radiative heat transfer, a one-dimensional two-flux method is used and the ray tracing method is also utilized to account for the wave interference effects. It is assumed that each interface is assumed diffusive but the spectral radiative properties are included. It is found that the selective heating region exists for various wavelengths and consequently may contribute to heat the poly-Si film. Using the formalism of the characteristic transmission matrix, the lumped structure reflectance, transmittance, and absorptance are calculated and they are compared with experimental data of the poly-Si film during the SPC process via the FE-RTA (Field-Enhanced RTA) technology.

• Fire Science and Engineering
• /
• v.23 no.2
• /
• pp.111-116
• /
• 2009

17 kinds of fire resistant paint which are currently used were painted on the MDF(middle density fiber board), which suitable to the regulation of Fire Service Act. And we investigate a ignition delay effect under a exposure condition of radiative heat of fire. Radiative heat flux was controlled from $10kW/m^2$ to $30kW/m^2$ using the cone heater. Ignition time, ignition type and surface temperature of the sample were measured. Based on the experimental result, critical heat flux of the fire resistant paint treated sample was $10kW/m^2$ and there were no ignition delay effect above the $30kW/m^2$. And it was found that it will be difficult to expect the fire resistant effect above $400^{\circ}C$ of sample surface temperature.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.21 no.1
• /
• pp.39-61
• /
• 2017

In this present article, we analyzed the heat and mass transfer characteristics of the nonlinear unsteady radiative MHD flow of a viscous, incompressible and electrically conducting fluid past an infinite vertical porous plate under the influence of Soret and chemical reaction effects. The effect of physical parameters are accounted for two distinct types of thermal boundary conditions namely prescribed uniform wall temperature thermal boundary condition and prescribed heat flux thermal boundary condition. Based on the flow nature, the dimensionless flow governing equations are resolved to harmonic and non harmonic parts. In particular skin friction coefficient, Nusselt number and Sherwood number are found to evolve into their steady state case in the large time limit. Parametric study of the solutions are conducted and discussed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.11
• /
• pp.3630-3638
• /
• 1996

An experimental study has been conducted to explore the behaviors of the radiative ignition of polymethylmetacrylate(PMMA) in a confined enclosure such as the ignition delay time, PMMA surface temperature, the ignition location and the ignition process. In addition, the effects of hot wall orientation on the ignition delay and PMMA surface temperature were studied. When the hot wall is located at the bottom, ignition delay time is the shortest. Ignition surface temperature becomes the lowest for the hot top wall case. These are due to buoyancy effect. Since the radiative heat flux of hot wall is rather lower than laser source, the ignition is considered to be controlled by the mixing process. Therefore, the ignition location, where appropriate mixture of fuel and oxygen exists, occurs near the hot wall. The flame propagates along the hot wall where there exists sufficient oxygen.

• Journal of The Korean Astronomical Society
• /
• v.29 no.2
• /
• pp.93-105
• /
• 1996

We have solved the radiative transfer problem using a Sobolev approximation with an escape probability method in case of the supersonic expansion of a stellar envelope to an ambient medium. The radiation from the expanding envelope turns out to produce a P-Cygni type profile. In order to investigate the morphology of the theoretical P-Cygni type profile, we have treated $V_\infty,\;V_{sto},\;\beta$ (parameters for the velocity field), it and E(parameter for collisional effect) as model parameters. We have investigated that the velocity field and the mass loss rate affect the shapes of the P-Cygni type profiles most effectively. The secondarily important factors are $V_\infty,\;V_{sto}$. The collisional effect tends to make the total flux increased but not so much in magnitude. We have infered some physical parameters of 68 Cyg, HD24912, and $\xi$ persei such as $V_\infty,\;M$ from the model calculation, which shows a good agreenment with the observational results.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.17 no.4
• /
• pp.435-441
• /
• 1988

The purpose of this study is to apply the zone method expressions for a gray, absorbing, emitting, and linearly anisotropic scattering medium enclosed in an infinite plane layer to evaluate heat transfer applications. The medium is assumed to be homogeneous and has a refractive index of unity. The boundary surfaces are opaque and gray, diffusely emitting and reflecting at a constant temperature. Radiative equilibrium condition, combined conductive and radiative heat transfer, and thermal ignition are studied in terms of the governing parameters, and the results are compared with previous studies. Wall heat flux results agree well with those of others. Except for the minor discrepancies observed for some cases, temperature results also agree well with those of previous studies. Good agreement with results from other methods indicates the accuracy of the zone method as well as its compatibility with other modes of heat transfer.