• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.4
• /
• pp.787-793
• /
• 2002

In this study, a bar impact test of low velocity was carried out to gain an insight into the damage mechanism and sequence induced in alumina plates(AD 85 and AD 90) under impact conditions. An experimental setup utilizing an instrumented long bar impact was devised, that can measure directly the impact force applied to the specimen and supply a compressive contact pressure to the specimen. During the bar impact testing, the influences of the contact pressure applied along the impact direction to the specimen on the fracture behavior were investigated. The measured impact force profiles explained well the damage behavior induced in alumina plates. The higher contact pressure to the specimen led to the less damage due to the suppression of radial cracks due to the increase in the apparent flexural stiffness of plate. It had produced the change of damage pattern developed in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates. The observed results showed the following sequence in damage developed: The development of cone crack at impact region, the formation of radial cracks from the rear surface of plate depending on the plate thickness, the occurrence of crushing within the cone envelope and the fragmentation.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.6
• /
• pp.1-9
• /
• 2004

For improvement of productivity and cutting tool lift, cutting force in end milling needs to be predicted accurately. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting force coefficients of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, fled, axial depth and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments.

• Journal of Institute of Convergence Technology
• /
• v.7 no.2
• /
• pp.1-5
• /
• 2017

The rotating electrodynamic wheel over a conductive plate produces thrust force as well as normal force. Specially, separating the conductive plate and spacing apart each part, the lateral stability of the rotating wheel is guaranteed due to the restoring force into neutral position. In this paper, the force characteristics of the electrodynamic wheel rotating over the conductive plate is analyzed using the finite element tool. First, the dominant parameters are identified considering the geometric configuration and the operating condition. And the sensitivity for the parameter deviation is quantified for the high force density. The above topology can be applied as an actuating principle for inter-city train as well as contact-free transfer device.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.848-853
• /
• 2001

A study about the shrink fits of rotor and retaining ring in generator was performed for the cases of three radial interference. The shrink-fitted retaining ring used to restrain the end turns of the winded coils in the rotor against centrifugal force requires very careful attention during design and manufacture because it has traditionally been the highest-stressed component of the generator. The contact pressures and residual stresses were obtained by the finite element analysis for each radial interference at zero, 100% rated, and 120% rated speeds, respectively. The results of analysis show that the radial interference in use needs to be increased carefully.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.356-363
• /
• 2011

Vibrations and noise in electrical machines are directly related to the characteristics of the radial forces on one hand, and mechanical behavior on the other [1, 4]. The characteristics of these forces depend on the air gap flux density, which is also influenced by other factors, such as stator slots and poles, saturation level, winding type, and certain faults. The aim of this work is to investigate the effect of eccentricity and demagnetization faults on electromagnetic noise generated by the external surface of Permanent Magnet Synchronous Machine [PMSM]. For this purpose, an analytical electromagnetic vibroacoustic model is developed. The results confirm the effect of eccentricity and demagnetization fault in generating some low modes radial forces.

• Tribology and Lubricants
• /
• v.12 no.2
• /
• pp.8-19
• /
• 1996

Scroll compressor using a slide bushing type radial compliant crank mechanism is modelled, and it's dynamic behaviour characteristics are analyzed. Sealing forces generated in the flank surfaces of the orbiting scroll depending on the distance, e, from slide bushing center to crank pin center are calculated. From the stable condition of orbiting scroll for the moment equilibrium in tangential direction, the range of e is determined as 0$r_o$. Transient response of a crankshaft supported by two journal bearings is investigated, considering applied load, moment, and unbalance force by eccentric mass. As a result, conical whirl mode with circular orbits are obtained. The characteristics of journal orbits and frictional losses are calculated with a variation of viscosity and bearing clearance.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.30-39
• /
• 1990

The behavior of a V-belt CVT was investigated both analytically and experimentally. It was found that as the torque load increased, the belt radial displacement increased in inward radial direction for the driven pulley while the radial displacement decreased slightly and increased for the driver pulley. The relative belt displacement for the driver was negligible compared with that of the driven. The experimental results were in good accordance with the theoretical results except for the inlet and exit region of the pulley. The speed ratio-torque load-axial force relationship derived from the belt behavior analysis also showed good agreement with the experiment. It is suggested that the results of this paper can be used as basic design informations of a V-belt CVT.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.2
• /
• pp.154-158
• /
• 2013

Reduction of electromagnetic vibration and acoustic noise from three-phase squirrel-cage induction motors (IMs) is very important, particularly from the standpoint of environmental considerations. Although the electromagnetic vibration of IMs has been studied for several years, the relationships between the radial distribution of the electromagnetic vibration and noise and the electromagnetic forces responsible for them have not yet been analyzed in sufficient detail. In the present study, we investigated this relationship experimentally for a small IM under different load conditions. Our results clearly show that the radial distributions of the dominant electromagnetic vibration and noise components match the mode shape of the dominant electromagnetic force producing these components.

• Journal of Advanced Marine Engineering and Technology
• /
• v.6 no.2
• /
• pp.69-91
• /
• 1982

The major factors which affect the crankshaft axial vibration are such items as the axial stiffness and mass of crankshaft, the thrust block stiffness, the propeller's entrained water and the exciting and damping forces of engine, propeller and shafting. Among above mentioned items, the axial stiffness and mass of crankshaft, thrust block stiffness and propeller's entrained water were treated in detail in part I, and so in this paper, the rest of above items will be studied. The exciting forces of crankshaft axial vibration are generated mainly from the gas explosion pressure of cylinder, the thrust fluctuation of propeller, and sometimes the torsional vibration of crankshaft induces the crankshaft axial vibration. As for the propeller thrust fluctuation, its harmonic components can be fairly exactly calculated from the experimental results of propeller in the towing tank, but as the calculation process is rather tedious and laborious, the empirical values are ordinarily used. On the other hand, the table of harmonic components of gas pressure has been already published by major slow speed diesel engine makers, but the axial thrust conversion factor of radial force is not unknown yet, and as its estimated value is unreliable, the axial vibration force of gas pressure is uncertain. As the calculation of damping force is very complicated and it includes some uncertain factors, the thoretically estimated amplitudes of axial vibration are much more incorrect in comparison with those of torsional vibrations. Authors have paid special attentions to deriving the theoretical calculation formula of axial conversion factor of radial force and damping force of crankshaft axial vibration and developed a computer program to calculate resonance amplitudes and additional stresses of crankshaft axial vibrations. Also, to check the reliability of the developed computer program, the axial vibrations of three ships' propulsion shaftings were analyzed and their results were compared with those of measured values and makers' results.

• Particle and aerosol research
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2018

The optical force on a perfectly reflecting sphere in a ray-optics regime is considered. With the assumption of geometric optics and a sphere smaller than the minimum waist of the illuminating beam, closed-form analytic expressions of the optical force are derived. Both axial and radial forces are expressed by a modified Bessel function of the first kind. The derived analytic expressions are compared to precise numerical computations of the exact optical force equations derived previously. In addition the error due to the small sphere assumption is estimated analytically.