• Resources Recycling
• /
• v.6 no.1
• /
• pp.29-34
• /
• 1997

The feasibility of using the industrial inorganic waste materials such as l~mestone sludge. Soundly sand. coal fly 'ash, and chemical glasses as a raw material for cement clinker by melting treatmeut was iovestigated. The slag wh~ch is obtained from thc melts of the mixtnres of waste materials is composed of P-C,S(ZCaO - SIOJ and C,AS(ZCaO . AI,O, . SiO,) phases. The effect of melting tempcrabre, coaling condition and CIS ratio on the fo~mation of P-C,S phasc was examed. In order to obtain thc P-CiS phase which is useful in thc utilhtion as a clinkcr malcrid, it B found that sudl considerations as low melting temperature as possible of the wastc mixhire, quenching the melts and law CIS ratio of the mlxhlre are necessary.

• Resources Recycling
• /
• v.24 no.6
• /
• pp.31-37
• /
• 2015

Ground granulated blast-furnace slag (GGBFS) which is by-product of steel industry has been recycled as a cement admixture though the other steel slags are used as aggregates. In this study, the electric arc furnace slag (EAFS) was used as a cement admixture after the reduction of iron oxide in the slag at the interface of molten slag and water quenching. Consequently, the reformed EAFS (REAFS) had higher grindability than that of granulated blast furnace slag. And in mortar tests, the strength properties of specimens using REAFS were 98% of plain specimens of GGBFS upto 20% replacement ratio of GGBFS with REAFS.

• Journal of the Korean Chemical Society
• /
• v.55 no.6
• /
• pp.932-935
• /
• 2011

Using tetrabutyl titanate as precursor, $Eu^{3+}$ doped $TiO_2$ nano-powder was prepared by sol-gel method, the nature of luminescence of nano-powder was studied. The interaction of chlorpyrifos with $Eu^{3+}$ doped $TiO_2$ was studied by absorption and fluorescence spectroscopy. The results indicated the fluorescence intensity of $Eu^{3+}$ doped $TiO_2$ was quenched by chlorpyrifos and the quenching rate constant ($k_q$) was $1.24{\times}10^{11}\;L/mol{\cdot}s$ according to the Stern-Volmer equation. The dynamics of photoinduced electron transfer from chlorpyrifos to conduction band of $TiO_2$ nanoparticle was observed and the mechanism of electron transfer had been confirmed by the calculation of free energy change (${\Delta}G_{et}$) by applying Rehm-Weller equation as well as energy level diagram. A new rapid method for detection of chlorpyrifos was established according to the fluorescence intensity of $Eu^{3+}$ doped $TiO_2$ was proportional to chlorpyrifos concentration. The range of detection was $5.0{\times}10^{-10}-2.5{\times}10^{-7}mol/L$ and the election limit ($3{\sigma}$) was $3.2{\times}10^{-11}$ mol/L.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.5
• /
• pp.730-736
• /
• 2007

The interaction of a polyoxometal (POM), K6SiW11Co(H2O)O39.10H2O (K6) as a Keggin, with human serum albumin (HSA) was studied by different methods and techniques. Binding studies show two sets of binding sites for interaction of POM to HSA. Binding analysis and isothermal calorimetery revealed that, the first set of binding site has lower number of bound ligand per mole of protein (ν), lower Hill constant (n), higher binding constant (K), more negative entropy (ΔS) and more electrostatic interaction in comparison to the second set of binding site. In addition, differential scanning calorimetery (DSC) and spectrophotometery data showed that, there are two energetic domains. The first domain is less stable (lower Tm and Cp) which corresponds to the tail segment of HSA and another with more stability is related to the head segment of HSA. Polyoxometal also decreases the stability of protein as Tm, secondary and tertiary structure as well as quenching of the fluorescence decrease. On other hand, perturbations in tertiary structure are more than secondary structure.

• Clean Technology
• /
• v.2 no.2
• /
• pp.100-125
• /
• 1996

After recycle of spent materials has been optimised, there remains a proportion of waste which must be dealt with in the most environmentally friendly manner available. For materials such as municipal waste, clinical waste, toxic waste and special wastes such as tyres, incineration is often the most appropriate technology. The study of incineration must take a process system approach covering the following aspects: ${\bullet}$ Collection and blending of waste, ${\bullet}$ The two stage combustion process, ${\bullet}$ Quenching, scrubbing and polishing of the flue gases, ${\bullet}$ Dispersion of the flue gases and disposal of any solid or liquid effluent. The design of furnaces for the burning of a bed of material is being hampered by lack of an accurate mathematical model of the process and some semi-empirical correlations have to be used at present. The prediction of the incinerator gas phase flow is in a more advanced stage of development using computational fluid dynamics (CFD) analysis, although further validation data is still required. Unfortunately, it is not possible to scale down many aspects of waste incineration and tests on full scale incinerators are essencial. Thanks to a close relationship between SUWIC and Sheffield Heat&Power Ltd., an extended research programme has been carried out ar the Bernard Road Incinerator plant in Sheffield. This plant consists of two Municipal(35 MW) and two Clinical (5MW) Waste Incinerators which provide district heating for a large part of city. The heat is distributed as hot water to commercial, domestic ( >5000 dwelling) and industrial buildings through 30km of 14" pipes plus a smaller pipe distribution system. To improve the economics, a 6 MW generator is now being added to the system.

• Korean Journal of Agricultural Science
• /
• v.43 no.3
• /
• pp.441-449
• /
• 2016

Agricultural tractors are designed using the empirical method due to the difficulty of measuring precise load cycles under various working conditions and soil types. Especially, directly drives various tractor implements, the power take off (PTO) gear. Therefore, alternative design methods using gear design software are needed for the optimal design of tractors. The objective of this study is to simulate fatigue life of the PTO gear according to the operating point of the tractor engine. The PTO gear was made with SCr415 alloy steel with carburizing and quenching treatments. The fatigue life of the PTO gear was simulated by using bending and contact stress according to the torque of the load levels. The PTO gear simulation was conducted by the KISSsoft commercial software for gear analysis. Bending and contact stress were calculated by the ISO 6336:2006 Method A and B. The simulation of fatigue life was calculated by the Miner's cumulative damage law. The total fatigue life of tractors can be estimated to 3,420 hours; thus, 3,420 hours of fatigue life were used in the simulation of the PTO gear of tractors. The main simulation results showed that the maximum fatigue life of the PTO gear was infinite fatigue life at maximum engine power. Minimum fatigue life of the PTO gear was 19.61 hours at 70% of the maximum engine power. Fatigue life of the PTO gear changed according to load of tractor. Therefore, tractor work data is needed for optimal design of the PTO gear.

• Corrosion Science and Technology
• /
• v.2 no.2
• /
• pp.68-74
• /
• 2003

The effects of Niobium on the structure and properties(especially electric properties) of passive film of Zirconium alloys in pH 8.5 buffer solution are examined by the photo-electrochemical analysis. For Zr-xNb alloys (x = 0, 0.45, 1.5, 2.5 wt%), photocurrent began to increase at the incident energy of 3.5 ~ 3.7 eV and exhibited the $1^{st}$ peak at 4.3 eV and the $2^{nd}$ peak at 5.7 eV. From $(i_{ph}hv)^{1/2}$ vs. hv plot, indirect band gap energies $E_g{^1}$= 3.01~3.47 eV, $E_g{^2}$= 4.44~4.91 eV were obtained. With increasing Nb content, the relative photocurrent intensity of $1^{st}$ peak significantly increased. Compared with photocurrent spectrum of thermal oxide of Zr-2.5Nb, It was revealed that $1^{st}$ peak in photocurrent spectrum for the passive film formed on Zr-Nb alloy was generated by two types of electron transitions; the one caused by hydrous $ZrO_2$ and the other created by Nb. Two electron transition sources were overlapped over the same range of incident photon energy. In the photocurrent spectrum for passive film formed on Zr-2.5Nb alloy in which Nb is dissolved into matrix by quenching, the relative photocurrent intensity of $1^{st}$ peak increased, which implies that dissolved Nb act as another electron transition source.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.89-94
• /
• 2019

Glass base sealant is required as a ceramic-ceramic joining material between α-alumina insulation cap and β-alumina electrolyte tube in the development of NaS battery cell package for electrical energy storage system. The fabrication of glass frit by thermal quenching method, phase analysis, particle size analysis, coefficient of thermal expansion and surface roughness according to the glass compositions were analyzed for the fabrication of glass sealing paste for ceramic-ceramic joining. Also, a new evaluation method of the adhesion strength of glass sealant at the small area in ceramic-ceramic joining component was proposed using conventional Dage bond tester that was used to measure the adhesion of solder ball joint.

• Journal of Radiation Protection and Research
• /
• v.26 no.4
• /
• pp.375-384
• /
• 2001

It is possible to count and perform quench correction on two ${\beta}$ -label samples so long as the maximum ${\beta}$-energies are sufficiently different. However, when 4he conventional technique is applied to the radioassay of a mixture of more than three nuclides, the reliability of the activities determined is considerably reduced, resulting from the large overlapping of liquid scintillation pulse height distributions of each nuclide. A technique that allows the activities of multiple ${\beta}$-labeled samples to be radioassayed was proposed by using the least square method. The technique was applied to mixture samples of $^3H,\;^{14}C,\;^{36}Cl$, and $^{90}Sr$. The analytical values were in good agreement with the reference values within 7% relative error.

• Korean Journal of Materials Research
• /
• v.24 no.7
• /
• pp.351-356
• /
• 2014

A spherical $Sr_4Al_{14}O_{25}:Eu^{2+}$ phosphor for use in white-light-emitting diodes was synthesized using a liquid-state reaction with two precipitation stages. For the formation of phosphor from a precursor, the calcination temperature was $1,100^{\circ}C$. The particle morphology of the phosphor was changed by controlling the processing conditions. The synthesized phosphor particles were spherical with a narrow size-distribution and had mono-dispersity. Upon excitation at 395 nm, the phosphor exhibited an emission band centered at 497 nm, corresponding to the $4f^65d{\rightarrow}4f^7$ electronic transitions of $Eu^{2+}$. The critical quenching-concentration of $Eu^{2+}$ in the synthesized $Sr_4Al_{14}O_{25}:Eu^{2+}$ phosphor was 5 mol%. A phosphor-converted LED was fabricated by the combination of the optimized spherical phosphor and a near-UV 390 nm LED chip. When this pc-LED was operated under various forward-bias currents at room temperature, the pc-LED exhibited a bright blue-green emission band, and high color-stability against changes in input power. Accordingly, the prepared spherical phosphor appears to be an excellent candidate for white LED applications.