• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.288-291
• /
• 2004

In this paper, to make ultra-high strength SFRCC with the range of compressive strength 180MPa, it was investigated the constitute factors of ultra-high strength SFRCC influenced on the compressive strength. The experimental variables were water-cementitious ratio, replacement of silica fume, size and proportion of sand, type and replacement of filling powder, and using of steel fiber in ultra-high strength SFRCC. As a result, in water-binder ratio 0.18, we could make ultra-high strength SFRCC with compressive strength 180MPa through using of silica fume, quartz sand with below 0.5mm, filling powder and steel fiber.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.765-768
• /
• 2005

This study is investigated the strength properties of ALC(Autocalved Lightweight Concrete) using SPS(Stone Powder Sludge), to develop recycling technique of SPS. At a given replacement percent of SPS and addition percent of foam, the results show that its the strength properties are equal or higher than the quartz used in a raw material of ALC, and it is also found that the addition percent of the foam and the strength properties have a certain relation of linear.

• 한국세라믹학회지
• /
• 제31권3호
• /
• pp.291-297
• /
• 1994

Cordierite powders were prepared by controlled hydrolysis of metal alkoxides with catalysts in water medium without using organic solvents. Water was adjusted to a certain pH by HC1 and NH4OH. $\alpha$-Cordierite powder was prepared from aluminum isopropoxide, tetraethyl orthosilicate and magnesium ethoxide mixed with water adjusted to pH of 3. At water pH of 11, $\alpha$-cordierite, mullite and $\beta$-quartz phases were coexisted. The powders were freeze dried, calcined and then fired at different temperatures. The characteristics of powders were examined by means of DTA, X-ray diffraction, FT-IR, and electron microscopy. It was found that $\alpha$-cordierite could be synthesized at temperature of 120$0^{\circ}C$ from the powders prepared by alkoxides with water medium without organic solvents.

• Korean Chemical Engineering Research
• /
• 제53권1호
• /
• pp.103-110
• /
• 2015

본 연구에서는 가스 하이드레이트 기술을 이용하여 철강 공정 배기가스로부터 $CO_2$를 분리하는데 사용하는 여러 촉진제의 성능을 조사하였다. 이 실험에서는 $CO_2/N_2$ 혼합가스 ($CO_2/N_2$=20/80, 40/60)와 $CO_2/N_2$ 이외에 CO, $H_2$가 첨가된 Blast furnace gas (BFG) 모델 가스를 대상 가스로 사용하였다. 촉진제로는 구조 II 하이드레이트를 형성한다고 알려진 tetrahydrofuran (THF), propylene oxide, 1,4-dioxane 를 사용하였으며, 각 가스에 대하여 촉진제를 농도별로 첨가했을 때 상평형점의 변화를 측정하였다. 상평형점은 "연속" Quartz crystal microbalance (QCM) 방식을 이용하였다. 또한, Powder X-ray diffraction (PXRD) 분석을 통하여 촉진제의 첨가가 가스 하이드레이트 구조에 미치는 영향을 알아보았다.

• 한국세라믹학회지
• /
• 제48권2호
• /
• pp.168-172
• /
• 2011

Alumina powder was added in a general porcelain (Backja) with clay, feldspar and quartz contents to promote the mullite ($3Al_2O_3{\cdot}2SiO_2$) generation in the porcelain. Low melting materials ($B_2O_3(450^{\circ}C)$, $MnO_3(940^{\circ}C)$, CuO($1080^{\circ}C$)) were doped at ~3 wt% to modify the sinterability of porcelain with a high alumina contents and promote the mullite generation. Green body was made by slip casting method with blended slurry and then, they were fired at $1280^{\circ}C$ for 1hr by a $2^{\circ}C/min$. Densifications of samples with high alumina contents (20~30 wt%) were impeded. As the doping contents of low melting materilas increased, the sinterability of samples was improved. The shrinkage rate and bulk density of samples were improved by doping with low melting materials. Mullite phase increased with increasing the low melting contents in the phase analyses. This means lots of alumina and quartz were transformed into mullite phase by low melting contents doping. In the results, high bending strength of samples with high alumina contents was accomplished by improving the densification and mullite generation in the porcelain.

• 자원환경지질
• /
• 제15권4호
• /
• pp.205-219
• /
• 1982

어성천 망간광상은 고생대 오르도비스기의 흥월리 돌로마이트층과 삼태산 석회암층에 관입한 석영반암맥을 따라 산출되는 표성광상이다. 망간광석은 산화망간광물들과 이에 수반되는 맥석광물들로 구성되어 있다. 산화망간광물들 중 란시아이트와 토도로카이트는 다량으로 산출되며, 버어네사이트, 엔소타이트, 연망간석, 캘코파나이트는 소량으로 산출된다. 맥석광물로는 방해석, 석고, 침철석, 레피도크로사이트, 석영, 견운모등이 산출된다. 산화망간광물들과 맥석광물들의 연구에는 현미경 관찰, 화학분석, 엑스선회절분석, 적회선흡수분광분석, 시차열분석 방법등이 이용되었다. 버어네사이트와 란시아이트의 관계가 엑스선회절분석과 적외선흡수분광분석법에 의하여 연구되었다. 이 두 광물들은 구조적으로 상당히 밀접한 관계가 있으나 서로 다른 광물종임이 적외선 흡수 스펙트럼연구에 의하여 확실시된다. 산화망간광물들은 표성환경하에서 교대작용, 용액으로부터의 침전, 재결정작용등에 의하여 생성되었다. 산화망간광물들의 생성순서는 다음과 같은 경향을 보여준다 : (능망간석)-(토도로카이트)-(버어네사이트, 란시아이트)-(엔소타이트, 연망간석, 캘코파나이트).

• 한국세라믹학회지
• /
• 제42권7호
• /
• pp.497-502
• /
• 2005

This study investigated the effects of the substrate and powder content on the fabrication of SiO$_{2}$ photonic crystals by evaporation method. Photonic crystals were self-assembled on quartz, Corning 1737 glass, slide glass, and ITa glass to verify the effects of the wetting angle and surface morphology. The powder contents of the solution were varied from 0.2 to 2.0 wt$\%$. The number of photonic crystal layers increased according to the decrease of wetting angle and surface roughness. The resultant photonic crystals showed the best optical characteristics when the number of photonic crystal layers was within 40 and 50. In addition, the intensity peak of Fabry¡?Perot fringes increased when the wetting angle was large and the particle size was small. Photonic crystals coated on ITO glass showed the highest reflectance peak of 63$\%$ relative intensity.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.213-213
• /
• 2010

In this thesis, we studied to increased to solar conversion efficiency of DSSC (dye-sensitized solar cell) using nanocrystalline $TiO_2$ semiconductor. We are preparation of $TiO_2$ photoelectrode, assembly the DSSC and put a focus in analyses electrochemical properties of DSSC and using Silica powder in $TiO_2$ photoelectrode for increase light scattering effect and improved conversion efficiency. It attempt to investigate the morphology of the photoelectrode and photovoltaic effects using field emission scanning electron microscopy (FE-SEM) and photovoltaic properties under illumination with AM 1.5 simulated sunlight. We got 146 % enhanced power conversion efficiency when the optimal content of quartz glass powder was 5 wt.% than that another content.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.719-724
• /
• 2001

The objective of this investigation was to separate silicon and silica for recycling by the liquid-liquid separation technique. In the preparation of silicon (Si) single crystal, a small amount of silicon is fixed on the surface of silica (quartz, $SiO_2$) crucible. The used crucible is crushed for recycling both silicon and silica in a high purity from the mixed powder. Zeta-potential of silicon and silica are almost the same at pH higher than 3. Their separation by simple flotation is ruled out. However, their hydrophobic characteristics are different in several different organic solvent from the measurement of contact angle. Therefore, the liquid-liquid extraction is employed to separate silicon and silica. The result indicates that the organic solvent mixed with dodecyl ammonium acetate could extracted the silicon powder at high purity (97-100%) with high recovery from the silica powder in the water phase.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.68-71
• /
• 2013

Reactive Powder Concrete (RPC) is an ultra high strength and high ductility cement-based composite material and has shown some promise as a new generation concrete in construction field. It is characterized by a silica fume-cement mixture with very low water-binder (w/b) ratio and very dense microstructure, which is formed using various powders such as cement, silica fume and very fine quartz sand (0.15~0.4mm) instead of ordinary coarse aggregate. However, the unit weight of cement in RPC is as high as 900~1,000 kg/㎥ due to the use of very fine sand instead of coarse aggregate, and a large volume of relatively expensive silica fume as a high reactivity pozzolan is also used, which is not produced in Korea and thus must be imported. Since the density of RPC has a heavy weight at 2.5~3.0 g/㎤. In this study, the modified RPC was made by the combination of ternary pozzolanic materials such as blast furnace slag and fly ash, silica fume in order to economically and practically feasible for Korea's situation. The fire resistance and structural behavior of the modified RPC exposed to high temperature were investigated.