• 한국항만학회지
• /
• 제12권2호
• /
• pp.323-328
• /
• 1998

A quartz crystal analyzer is utilized to monitor the corrosion process of an aluminum surface of a quartz crystal for marine sensor by sea water. A quartz crystal having 2000 $\AA$ of aluminum layer is installed in a specially designed cell and is in contact with sea water imitated electrolyte solution. While a constant potential is applied to the cell, the resonant frequency and resonant resistance are simultaneously measured using the quartz crystal analyzer. In addition, surface topographs are taken with an atomic force microscope(AFM) and the element analysis of the surface is conducted using an energy dispersive X-ray spectrometer(EDX). The simultaneous measurement of resonant frequency and resonant resistance during the corrosion process explains the change of surface structure caused by the corrosion. The variation of resonant frequency addresses the amount surface metal dissolution. As a conclusion, it is found that a simple measurement using the quartz crystal analyzer can replace the complex monitoring employing large equipments in the investigation of a corrosion process of sensor surface.

• 전기학회논문지
• /
• 제58권3호
• /
• pp.559-565
• /
• 2009

In this paper, we invented a new and unique technique for the sterilization of Escherichia coli(E. coli) in polluted water. We applied a rich ultra-violet(UV) light from pulsed xenon flashlamp and photocatalyst(TiO2) to sterilize E. coli in polluted water. This method based on the use of UV light and photocatalyst is eco-friendly and does not cause secondary pollution. The proposed elliptical reactor is able to concentrate on quartz sleeve coated TiO2 or general quartz sleeve. The primary objective of our research was to determine the important parameters such as pulse repetition rate and input voltage and to know on the sterilizing efficiency of quartz sleeve coated TiO2 and general quartz sleeve. We obtained to achieve 99.999% sterilization in as little as 6 pulses at 800V in case of quartz sleeve coated Ti02, and 10 pulses at 800V in case of general quartz sleeve for 5 minutes. Although transmitted light of quartz sleeve coated TiO2 is deceased, the sterilizing efficiency is increased by 40% than general quartz sleeve. The reason of high sterilizing efficiency is that generated hydroxyl radical(OH) by photocatalyst and is able to concentrate light at a focus by using elliptical reactor.

• 한국산업보건학회지
• /
• 제1권2호
• /
• pp.238-245
• /
• 1991

This study was analysis of ${\alpha}$-quartz in the 37 worker's lung died of coal workers' pneumoconiosis(CWP) and in the 9 normal's lung by Fourier transform infrared spectrophotometer. The results were as follows : 1. The dried lung weight percents in wet lung weight were 24.4%, 25.4%, coal workers' pneumoconiosis and normal lungs, respectively. Ash weight percents in dried lung weight were 7.7%, 5.0%, coal workers' pneumoconiosis and normal lungs, respectively. 2. The presision (as of coefficient of variation) for the ${\alpha}$-quartz determination were 2.6% in standard quartz (ranged from 9.9 to $198.0{\mu}g$) and 3.7% in ashed lung samples. 3. The characterstic ${\alpha}$-quartz absorption spectra in lungs of CWP were only shawn by LTA ashing. 4. Geometric mean of ${\alpha}$-quartz concentration in CWP lung was 173mg/100g dried lung. 5. The concentrations of ${\alpha}$-quartz in Korean CWP lungs were similar to those of foreign coal miner's lungs.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.123-129
• /
• 2022

Quartz (SiO2) has high abrasion and heat resistances and excellent chemical and mechanical properties; therefore, it is used in various industries, such as machinery, chemistry, optics, and medicine. Quartz is a high-hardness and brittle material and is classified as the topmost difficult-to-cut material, which is because of the cracking or chipping at the edge during processing. Corner wear, such as cracks and chippings that occur during cutting, is a major cause for the deterioration in the machining quality. Therefore, many researchers are investigating various techniques to process quartz effectively. However, owing to the mechanical properties of quartz, most studies have been conducted on grinding, micromachining, and microdrilling. Few studies have been conducted on quartz processing. The purpose of this study was to analyze the machining characteristics according to the machining factors during the slot machining of quartz using a cubic boron nitride (CBN) tool and to select the optimal machining conditions using the Taguchi method. The machining experiment was performed considering three process variables: the spindle speed, feed rate, and depth of cut. The cutting force and surface roughness were analyzed according to the processing conditions.

• 한국산업보건학회지
• /
• 제23권2호
• /
• pp.75-83
• /
• 2013

Objectives: This study was conducted to estimate quartz concentrations in the airborne respirable dust from concrete manufacturing industries and to compare performance of two analytical methods, direct on filter(DOF) and the transfer methods in the Fourier Transform Infrared Spectroscopy(FTIR). Methods: Total 36 area samples were collected from 8 concrete manufacturing industries. Each respirable dust sample was collected by a 25 mm cassette attached to a 10 mm Dorr-Oliver nylon cyclone. The quartz content was estimated using the intensity of the absorption peak of quartz at $799cm^{-1}$ by FTIR. Results: By the comparison of quartz content in respirable dust between the two methods, the results of using DOF method were higher than that of transfer method. And the result of quartz concentrations in respirable dust estimated by DOF method were mostly higher than those by transfer method. Statistically significant difference of quartz concentrations in respirable dust were not found in shakeout, input, loading and transporting processes by two methods. But quartz concentrations in the molding process had the statistically significant difference between DOF and transfer method. Conclusions: The results of the study is suggested that, it be needed to correct the influence of the interferences in order to establish the DOF method when interfering minerals have an effect on quantitative analysis of quartz in respirable dust by the direct on filter method with FTIR.

• Asian Journal of Atmospheric Environment
• /
• 제11권2호
• /
• pp.107-113
• /
• 2017

This study describes (1) the impact of positive sampling artifacts caused by not only a filter-based sampling, but also a denuder-based sampling in the determination of particle-phase organic carbon (POC), (2) the effect of sample flow rate on positive artifacts, and (3) an optimum flow rate that provides a minimized negative sampling artifact for the denuder-based sampling method. To achieve the goals of this study, four different sampling media combinations were employed: (1) Quartz filter-alone (Q-alone), (2) quartz filter behind quartz-fiber filter (QBQ), (3) quartz filter and quartz filter behind Teflon filter (Q-QBT), and (4) quartz filter behind carbon-based denuder (Denuder-Q). The measurement of ambient POC was carried out in an urban area. In addition, to determine gas-phase OC (GOC) removal efficiency of the denuder, a Teflon filter and a quartz filter were deployed upstream and downstream of the denuder, respectively with varying sample flow rates: 5, 10, 20, and 30 LPM. It was found that Q-alone sampling configuration showed a higher POC than QBQ, Q-QBT, and Denuder-Q by 12%, 28%, and 23%, respectively at a sample flow rate of 20 LPM due to no correction for positive artifact caused by adsorption of GOC onto the filter. A lower quantity of GOC was collected from the backup quartz filter on QBQ than that from Q-QBT. This was because GOC was not in equilibrium with that adsorbed on the front quartz filter of QBQ during the sampling period. It is observed that the loss of particle number and mass across the denuder increases with decreasing sample flow rate. The contribution o f positive arti facts to POC decreased with increasing sample flow rate, showing 29%, 25%, and 22% for 10, 20, and 30 LPM, respectively. The 20 LPM turns out to be the optimum sample flow rate for both filter and denuder-based POC sampling.

• 자원환경지질
• /
• 제27권4호
• /
• pp.335-343
• /
• 1994

The Eonyang amethyst deposits are composed of vug quartz emplaced in the Eonyang granites of Mesozoic Cretaceous age. The Eonyang granites are composed of biotite granite, porphyritic biotite granite, aplite and miarolitic granite. The petrochemical data of the Eonyang granites show the trend of subalkaline magma, calc-alkaline magma, I-type granitoid and magnetite series. The vug quartz show the characteristic growth zoning (white quartz-smoky quartz-amethyst) from wall side. Generally fluid inclusions in the vug quartz can be divided into four main types based on compositions (I-type: gas inclusion, II-type: liquid inclusion, III-type: polyphase inclusion, IV-type: liquid $CO_2$-bearing inclusion). Solid phase of polyphase inclusions are halite(NaCl), sylvite(KCl), hematite ($Fe_2O_3$) and unknown anisotropic solid. Homogenization temperatures inferred from the fluid inclusion study ranges from $440^{\circ}C$ to $485^{\circ}C$ in white quartz, from $227^{\circ}C$ to $384^{\circ}C$ in smoky quartz, from $133^{\circ}C$ to $186^{\circ}C$ in amethyst, respectively. Salinities of fluid inclusions in each mineralization stages ranges from 40 wt.% to 58 wt.% in white and smoky quartz, from 1.0 wt.% to 8.7 wt.% in amethyst respectively. A consideration of the pressure regime during vug quartz deposition based on the boiling evidence suggests lithostatic pressure of less than 72 bars. This range of pressure indicate that vug quartz lay at depth of 750 m below the surface at the during mineralization.

• 광물과 암석
• /
• 제34권1호
• /
• pp.1-14
• /
• 2021

운산 금 광상은 한반도의 3대(대유동 광상, 광양 광상) 금 광상중의 하나였다. 이 광상의 지질은 선캠브리아기의 변성퇴적암류와 중생대의 반상화강암으로 구성된다. 이 광상은 선캠브리아기의 변성퇴적암류와 중생대의 반상화강암내에 발달된 단층대를 따라 충진한 함 금 석영맥 광상으로 조산형 금 광상에 해당된다. 이 광상의 석영맥은 광물조합에 따라 1) 방연석-석영맥형, 2) 자류철석-석영맥형, 3) 황철석-석영맥형, 4) 페크마틱 석영맥형, 5) 백운모-석영맥형 및 6) 단순석영맥형으로 분류된다. 연구된 석영맥은 황철석-석영맥형이며 견운모화작용, 녹니석화작용 및 규화작용이 관찰된다. 백색운모는 유색대에서 백색석영, 황철석, 녹니석, 금홍석, 모나자이트, 저어콘, 인회석, 칼리장석 및 방해석 등과 함께 세립질 내지 중립질 입단으로 산출된다. 이 백색운모의 화학조성은 (K0.98-0.86Na0.02-0.00Ca0.01-0.00Ba0.01-0.00 Sr0.00)1.00-0.88(Al1.70-1.57Mg0.22-0.09Fe0.23-0.10Mn0.00Ti0.04-0.02Cr0.01-0.00V0.00Ni0.00)2.06-1.95 (Si3.38-3.17Al0.83-0.62)4.00O10(OH2.00-1.91F0.09-0.00)2.00로써 이론적인 이중팔면체형 운모류 값보다 Si가 높고 K, Na, Ca는 낮다. 이 광상의 엽리상 석영맥에서 산출되는 백색운모의 화학조성 변화는 팬자이틱(phengitic) 또는 Tschermark 치환[(Al3+)VI+(Al3+)IV <-> (Fe2+ 또는 Mg2+)VI+(Si4+)IV] 및 직접적인 (Fe3+)VI <-> (Al3+)VI 치환에 의해 일어났음을 알 수 있다. 엽리상 석영맥에서 산출되는 녹니석의 화학조성은 (Mg1.11-0.80Fe3.69-3.14Mn0.01-0.00Zn0.01-0.00K0.07-0.01Na0.01-0.00Ca0.04-0.01Al1.66-1.09)5.75-5.69 (Si3.49-2.96Al1.04-0.51)4.00O10 (OH)8로써 이론적인 녹니석보다 Si 함량이 높다. 이 녹니석의 화학조성 변화는 팬자이틱(phengitic) 또는 Tschermark 치환(Al3+,VI+Al3+,IV <-> (Fe2+ 또는 Mg2+)VI+(Si4+)IV) 및 팔면체적 Fe2+ <-> Mg2+ (Mn2+) 치환에 의해 일어났음을 알 수 있다. 따라서 운산 광상의 엽리상 석영맥 및 변질광물은 조산운동 시 연성전단(ductile shear) 시기에 형성되었음을 알 수 있다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권7호
• /
• pp.508-513
• /
• 1999

The response properties of quartz crystal coated with stearic acid LB films to organic gases were investigated by measuring the shift of resonant frequency. Stearic acid was used as a sensing material and deposited on the surface of quartz crystal using the Langmuir-Blodgett(LB) method. The effect of temperature on the quartz crystal coated with stearic acid LB films was also investigated by Scanning Maxwell-stress Microscopy(SMM). As a result, the sensitivity of the quartz crystal coated with LB films to organic gases is dependent on temperature, thickness of LB film and molecular weight of organic gas.

• 한국세라믹학회지
• /
• 제29권12호
• /
• pp.981-989
• /
• 1992

This is a study on the effects of cristobalite transition of quartz in semi-vitrious whiteware body, as addition of alkali and alkali earth oxides, prepared by pottery stone, feldspar, kaolin and clay minerals. The amounts of ${\alpha}$-quartz to ${\alpha}$-cristobalite transition, F.O.C. (fraction of cristobalite), were increased with firing temperature. In MgO added body, ${\alpha}$-quartz was decreased and the formation of cristobalite was increased. Effects of K2O addition was remarkably decreased the formation of cristobalite. Additive effects of MgO and K2O were confirmed that it was very different to variation of transition temperature of metakaolinite to Si-Al spinel structure in thermal reaction of kaolinite minerals. Result CaO addition was ineffective to transition temperature, and the transition temperature in Na2O added body was decreased, but relative intensity of quartz and cristobalite crystal in XRD results was decreased. This was characterized by the effects on the formation of liquid phase much more.