• Steel and Composite Structures
• /
• v.9 no.3
• /
• pp.255-274
• /
• 2009

This paper presents an experimental study of a newly developed composite floor system, built up from thin-walled C-profiles and upper concrete deck. Trapezoidal sheeting provides the formwork and the fastening of the sheet transmits the shear forces between the C-profiles and the deck. The modified formation of the standard self-drilling screw in the beam-to-sheet connection is applied as shear connector. Push-out tests are completed to study the composite behaviour of the different connection arrangements. On the basis of the test results the behaviour is characterized by the observed failure modes. The design values of the connection stiffness and strength are calculated by the recommendation of Eurocode 4. In the next phase of the experimental study six full-scale composite beams are tested. The global geometry is based on the proposed geometry of the developed floor system. The applied shear connections are selected as the most efficient arrangements obtained from the push-out tests. The experimental behaviour of the composite beams are discussed and evaluated. As a conclusion of the experimental study the Eurocode 4 plastic design method is validated for the developed composite floor.

• Journal of Korean Association for Spatial Structures
• /
• v.18 no.2
• /
• pp.121-128
• /
• 2018

The push-out tests have been conducted on the specimens which consist of the steel beam with U-shape section and the cap-type shear connectors with constant intervals. Existing equations for the evaluation of shear connector strength have been investigated on the basis of test results. The reinforcing bars for longitudinal reinforcement and the penetrative bars for transverse reinforcement didn't have much effect on the shear capacity of the cap-type shear connector. The larger the width of cap-type shear connector was profiled, the greater the shear strength turned. The shear capacities of cap-type shear connectors with constant intervals were evaluated on the basis of push-out test results, and those were possible to be determined with proper safety margin using the Eurocode 4. The slip capacity of cap-type shear connector was shown to exceed the limit value of 6mm for sufficiently ductile behavior.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.1
• /
• pp.113-120
• /
• 2002

A shear connection in composite bridges with precast decks has considerable characteristics different from cast-in-place deck bridges such as shear pocket and bedding layer. Thus, it is necessary to build design basis of the shear connector in precast decks through the experiments. In order to estimate fatigue life of shear connector in precast deck bridges, push-out fatigue tests were conducted with parameter, bedding layer thickness. As a result of the tests, failure modes of shear connector were observed. Consequently, empirical S-N curve equations of stud shear connector in precast deck bridges were proposed in this paper.

• The Journal of the Korea Contents Association
• /
• v.12 no.9
• /
• pp.389-395
• /
• 2012

This research analyzed the peak impulsive force, maximum velocity and a spot of fist's maximum velocity comparing stop-jirugi and push-jirugi. 7 males volunteered for this experiment. peak impulsive force was measured by PS2142 force platform[10], and maximum velocity of fist was measured by PS2103A motion sensor[12]. All of data was collected in the data studio and t-test was applied using SAS 9.1 package. The following conclusions were drawn. First, stop-jirugi's peak impulsive force was greater (P<.01) than that of push-jirugi. Second, push-jirugi's maximum velocity of fist was greater (P<.01) than that of stop-jirugi. Third, stop-jirugi's maximum velocity of fist was occurred on 69.14% of arm's length and that of push-jirugi was occurred on 75.66%. This maximum velocity spot was statistically significant difference(p<.001).

• Restorative Dentistry and Endodontics
• /
• v.48 no.1
• /
• pp.8.1-8.8
• /
• 2023

Objectives: This study was designed to evaluate the parameters of bonding performance to root dentin, including push-out bond strength and dentinal tubular biomineralization, of a hydraulic bioceramic root-end filling material premixed with dimethyl sulfoxide (Endocem MTA Premixed) in comparison to a conventional powder-liquid-type cement (ProRoot MTA). Materials and Methods: The root canal of a single-rooted premolar was filled with either ProRoot MTA or Endocem MTA Premixed (n = 15). A slice of dentin was obtained from each root. Using the sliced specimen, the push-out bond strength was measured, and the failure pattern was observed under a stereomicroscope. The apical segment was divided into halves; the split surface was observed under a scanning electron microscope, and intratubular biomineralization was examined by observing the precipitates formed in the dentinal tubule. Then, the chemical characteristics of the precipitates were evaluated with energy-dispersive X-ray spectroscopic (EDS) analysis. The data were analyzed using the Student's t-test followed by the Mann-Whitney U test (p < 0.05). Results: No significant difference was found between the 2 tested groups in push-out bond strength, and cohesive failure was the predominant failure type. In both groups, flake-shaped precipitates were observed along dentinal tubules. The EDS analysis indicated that the mass percentage of calcium and phosphorus in the precipitate was similar to that found in hydroxyapatite. Conclusions: Regarding bonding to root dentin, Endocem MTA Premixed may have potential for use as an acceptable root-end filling material.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5051-5059
• /
• 2015

Structural behaviour of the front loader for an agricultural tractor was analyzed for three impact test conditions: drop and catch, corner pull, and corner push. Rigid-body dynamic, transient structural, and static structural analyses were conducted using a commercial finite element software. Analysis of the drop and catch test dealt with the case that the bucket located at the maximum elevation was dropped and catched through three steps. Analysis of the corner pull test dealt with the case that the bucket constrained to the ground by a chain at its corner was raised suddenly. Analysis of the corner push test dealt with the case that the corner of the bucket collided with an obstacle. Results of analyses of the three test conditions showed that maximum stress occurs at the geometrically discontinuous location in the mount and is caused from local stress concentration. Results of the present research can be utilized as a guideline to achieve more reliable and safe structural design of the front loaders.

• Physical Therapy Korea
• /
• v.18 no.1
• /
• pp.1-8
• /
• 2011

Push-up plus has been advocated for increasing the activity of the serratus anterior muscle, the most critical scapular stabilizer. However, no previous study has reported the possibility of compensatory motion on the part of the pectoralis major, which could substitute for the action of the serratus anterior during push-up plus. The aim of the current study was to investigate the immediate effect of electromyography (EMG) biofeedback of the pectoralis major muscle on the pectoralis major, upper trapezius, and serratus anterior muscles during push-up plus. Fourteen healthy young subjects voluntarily participated in this study; each subject performed push-up plus from the quadruped position, in two conditions (i.e., with or without visual and auditory biofeedback). Surface EMG was used to measure pectoralis major, serratus anterior, and upper trapezius activity. A paired t-test was used to determine any statistically significant difference between the two conditions. Additionally, effect size was calculated to quantify the magnitude of EMG biofeedback in each muscle. Visual and auditory feedback reduced pectoralis major muscle activity significantly (p=.000) and increased the serratus anterior muscle activity significantly (p=.002), but did not induce a significant difference in upper trapezius muscle activity (p=.881). Thus, it is concluded that the visual and auditory feedback of pectoralis major muscle activity can be used to facilitate serratus anterior muscle activity during push-up plus.

• Restorative Dentistry and Endodontics
• /
• v.44 no.4
• /
• pp.37.1-37.10
• /
• 2019

Objectives: This study evaluated the bond strength of various fiberglass post cementation techniques using different resin-based composites. Materials and Methods: The roots from a total of 100 bovine incisors were randomly assigned to 5 treatment groups: G1, post + Scotchbond Multi-Purpose (SBMP) + RelyX ARC luting agent; G2, relined post (Filtek Z250) + SBMP + RelyX ARC; G3, individualized post (Filtek Z250) + SBMP; G4, individualized post (Filtek Bulk-Fill) + SBMP; G5, individualized post (Filtek Bulk-Fill Flow) + SBMP. The samples were subjected to the push-out (n = 10) and pull-out (n = 10) bond strength tests. Data from the push-out bond strength test were analyzed using 2-way analysis of variance (ANOVA) with the Bonferroni post hoc test, and data from the pull-out bond strength test were analyzed using 1-way ANOVA. Results: The data for push-out bond strength presented higher values for G2 and G5, mainly in the cervical and middle thirds, and the data from the apical third showed a lower mean push-out bond strength in all groups. No significant difference was noted for pull-out bond strength among all groups. The most frequent failure modes observed were adhesive failure between dentine and resin and mixed failure. Conclusions: Fiberglass post cementation using restorative and flowable bulk-fill composites with the individualization technique may be a promising alternative to existing methods of post cementation.

• Restorative Dentistry and Endodontics
• /
• v.39 no.4
• /
• pp.282-287
• /
• 2014

Objectives: The aim of the present study was to investigate the bond strength of RelyX Unicem (3M) to root canal dentin when used as an endodontic sealer. Materials and Methods: Samples of 24 single-rooted teeth were prepared with Gates Glidden drills and K3 files. After that, the roots were randomly assigned to three experimental groups (n = 8) according to the filling material, (1) AH Plus (Dentsply De Trey GmbH)/Gutta-Percha cone; (2) Epiphany SE (Pentron)/Resilon cone; (3) RelyX Unicem/Gutta-Percha cone. All roots were filled using a single cone technique associated to vertical condensation. After the filling procedures, each tooth was prepared for a push-out bond strenght test by cutting 1 mm-thick root slices. Loading was performed on a universal testing machine at a speed of 0.5 mm/min. One-way analysis of variance and Tukey test for multiple comparisons were used to compare the results among the experimental groups. Results: Epiphany SE/Resilon showed significantly lower push-out bond strength than both AH Plus/Gutta-Percha and RelyX Unicem/Gutta-Percha (p < 0.05). There was no significant difference in bond strength between AH Plus/Gutta-Percha and RelyX Unicem/Gutta-Percha (p > 0.05). Conclusions: Under the present in vitro conditions, bond strength to root dentin promoted by RelyX Unicem was similar to AH Plus. Epiphany SE/Resilon resulted in lower bond strength values when compared to both materials.

• Steel and Composite Structures
• /
• v.18 no.2
• /
• pp.497-517
• /
• 2015

This study evaluates behavior of the Y-type perfobond rib shear connector proposed by Kim et al. (2013). In addition, an empirical shear resistance formula is developed based on push-out tests. Various types of the proposed Y-type perfobond rib shear connectors are examined to evaluate the effects of design variables such as concrete strength, number of transverse rebars, and thickness of rib. It is verified that higher concrete strength increases shear resistance but decreases ductility. Placing transverse rebars significantly increases both the shear resistance and ductility. As the thickness of the ribs increases, the shear resistance increases but the ductility decreases. The experimental results indicate that a Y-type perfobond rib shear connector has higher shear resistance and ductility than the conventional stud shear connector. The effects of the end bearing resistance, resistance by transverse rebars, concrete dowel resistance by holes, and concrete dowel resistance by Y-shape ribs on the shear resistance are estimated empirically based on the push-out test results and the additional push-out test results by Kim et al. (2013). An empirical shear resistance formula is suggested to estimate the shear resistance of a Y-type perfobond shear connector for design purposes. The newly developed shear resistance formula is in reasonable agreement with the experimental results because the average ratio of measured shear resistance to estimated shear resistance is 1.024.