• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.223-228
• /
• 2017

Aluminum nitride (AlN) powder was successfully synthesized at low temperature via carbothermal reduction and nitridation (CRN) assisted by microwave heating. The synthesis processes of AlN powder were investigated with X-ray diffraction, FE-SEM, FT-IR and TGA/DSC. Aluminum nitrate was used as an oxidizer and aluminum source, urea as fuel, and glucose as carbon source. These starting materials were mixed with D.I water and reacted in a flask at $100^{\circ}C$ for 20 minutes. After the reaction was finished, black foamy intermediate product was formed, which was considered to be an amorphous $Al_2O_3$ particles through intermediate product obtained by solution combustion synthesis (SCS) at the results of X-ray diffraction patterns and FT-IR. This intermediate product was nitridated at temperatures of $1300^{\circ}C$ and $1400^{\circ}C$ in $N_2$ atmosphere by a microwave heating furnace and then decarbonated at $600^{\circ}C$ for 2 hours in air. It should be noticed from FE-SEM images that as nitridated particles, identified as AlN from X-ray diffraction patterns, are covered with carbon residues. After decarbonating the nitridated powders, the spherical pure AlN powders were obtained without alumina and their particle sizes were dependent on the nitridating temperature with high temperature of $1400^{\circ}C$ giving large particles of around 70~100 nm.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.1
• /
• pp.11-15
• /
• 2008

The composite membrane for direct methanol fuel cell (DMFC) was developed using $H_3O^+-{\beta}"-Al_2O_3$ powder and perfluorosulfonylfluroride copolymer (Nafion) resin. The perfluorosulfonylfluroride copolymer (Nafion) resin was mixed with $H_3O^+-{\beta}"-Al_2O_3$ powder and it was made to sheet form by hot pressing. The electrodes were prepared with 60 wt% PtRu/C and 60wt% Pt/C catalysts for anode and cathode, respectively. The morphology and the chemical composition of the composite membrane have been investigated by using SEM and EDXA, respectively. The composite membrane and $H_3O^+-{\beta}"-Al_2O_3$ were analyzed by using FT-IR and XRD. The methanol permeability of the composite membranes was also measured by gas chromatography (GC). The performance of the MEA containing the composite membrane (2wt% $H_3O^+-{\beta}"-Al_2O_3$) was higher than that of normal pure Nafion membrane at high operating temperature (e.g. $110^{\circ}C$), due to the homogenous distribution of $H_3O^+-{\beta}"-Al_2O_3$, which decreased the methanol permeability through the membrane and enhanced the water contents in the composite membrane.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.120-124
• /
• 2010

Monometallic, bimetallic and trimetallic particles consisting of different weight compositions of Pt-Pd-Rh over pure alumina wash coats have been synthesized and their catalytic performance on methane conversion was studied from 150 to $600^{\circ}C$. Different catalyst formulations with variable Pt, Pd and Rh contents for bimetallic and trimetallic systems were tried and $Pt_{(1.5)}Rh_{(0.3)}/Al_2O_3$ and $Pt_{(1.0)}Pd_{(1.0)}Rh_{(0.3)}/Al_2O_3$ shows low $T_{50}$ and $T_{90}$ temperatures. Bimetallic and trimetallic particle synergism acts as three way catalysts and therefore, all the catalysts show 100% methane conversion. The effect of supports such as $ZrO_2$ and $TiO_2$ on methane combustion was investigated; from $T_{50}$ and $T_{90}$ results both $Al_2O_3$ and $ZrO_2$ are suitable supports for low temperature methane combustion.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2819-2822
• /
• 2010

Forest of single-walled carbon nanotubes (SWNTs) was grown at $450^{\circ}C$ by water-plasma chemical vapor deposition using ultrathin iron on alumina supporting film. The growth rate of the SWNT forest is ${\sim}0.9\;{\mu}m/min$, and the diameters of nanotubes are mainly in a range of 3.0 ~ 3.5 nm. The low intensity ratio of D- to G-band ($I_D/I_G$ ~ 0.098) in Raman spectra indicates that our SWNT forest grown at $450^{\circ}C$ is fairly pure and crystalline. This low temperature growth of SWNT forest may enable variable applications requiring the vertically-aligned nanotubes to obtain large surface area.

• Journal of the Korean Ceramic Society
• /
• v.29 no.10
• /
• pp.822-826
• /
• 1992

SiO2 doped sapphire single crystals were grown by Verneuil method using feed material which prepared by adding SiO2 in Al2O3. Crystal growing were attempted with varing doping amount of SiO2 from 0.01 to 1.0 wt% and when the doping amount of SiO2 were 0.01~0.04 wt%, single crystals could be attained. Starting materials for feed powder were 99.99% purity alumina and extra pure SiO2 powder. Mixing these two materials by wet milling for 24 hours and drying the mixture and then was calcined at 900~110$0^{\circ}C$ for 2~4 hours. The grown crystals had yellowish color and were somewhat transparent. During growing process the flow range of oxygen was 5~7.5ι/min and of hydrogen was 13~25ι/min, the average growth rate was 7.0~11 mm/hr. The pressure of gases were fixed at 5psi. The color of crystal was appeared and mechanical property of sapphire was developed by doping of SiO2.

• Journal of the Korean Ceramic Society
• /
• v.28 no.1
• /
• pp.20-28
• /
• 1991

Fracture of Al2O3 tubes for different loading path under combined tension/torsion was investigated. Macroscopic directions of crack propagation agreed well with the maximum principal stress criterion, independent of the loading path. However, fracture strength from the proportional loading test($\tau$/$\sigma$= constant) showed either strengthening or weakening compared to that from uniaxial tension, depending on the ratio $\tau$/$\sigma$. The Weibull theory was capable to predict the strengthening of fracture strength in pure torsion, but not the weakening in the proportional loading condition. The strengthening or weakening of fracture strength in the proportional loading condition was explained by the effect of shear stresses in the plane of randomly oriented microdefects. Finally, a new empirical fracture criterion was proposed. This criterion is based on a mixed mode fracture criterion and experimental data for fracture of Al2O3 tubes under combined tension/torsion. The proposed fracture criterion agreed well with experimental data for both macroscopic directions of crack propagation and fracture strengths.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.2
• /
• pp.101-106
• /
• 1999

Hydrogen solubility in internally oxidized Pd-Mo(Al) alloys has been studied at 323 K from the measurements of pressure-composition(p-c) isotherms. Internal oxidation of $Pd_{0.985}Al_{0.015}$ and $Pd_{0.97}Mo_{0.03}$ alloys results in the precipitation of Al and Mo particles in a matrix of pure Pd. It has been observed that the presence of the aluminum and molybdenum oxide precipitates results in an enhanced hydrogen solubility in the dilute phase region of Pd-H in a Pd/aluminum(molybdenum)oxide composites. Hydrogen solubility enhancements due to the presence of residual stresses around ceramic particles have been observed from p-c isotherms determined at 323 K after oxidation at 1073 K. The solubility enhancements in completely internally oxidized alloys are greater than that in partially oxidized alloys. The stress fields near the ceramic precipitates are the major source of the solubility enhancements. Transmission electron microscopy indicates that alumina precipitates are nanometer-sized and coherent with the Pd matrix after oxidation.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.58-60
• /
• 2004

The $BaTiO_3/SrTiO_3$ heterolayered thick films were fabricated on alumina substrate by screening printing method. The obtained films were sintered at $1400^{\circ}C$ with bottom electrode of Pt for 2 hours. The structural and electrical properties of $BaTiO_3/SrTiO_3$ heterolayered thick films were compared with pure $BaTiO_3$ and $SrTiO_3$ films. The (Ba,Sr)$TiO_3$ phase was appeared at the $BaTiO_3/SrTiO_3$ heterolayered thick films. The thickness of $BaTiO_3/SrTiO_3$ heterolayered thick film, obtained by one printing, was about $50{\mu}m$. The dielectric constant and dielectric loss of the $BaTiO_3/SrTiO_3$ heterolayered thick films were about 1964, 5.5% at 1KHz, respectively.

• Journal of the Korean Ceramic Society
• /
• v.56 no.1
• /
• pp.37-48
• /
• 2019

The objective of this research is to analyze the fracture toughness of pure and silica co-doped yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) bioceramics containing 0.1 and 0.2 wt.% of alumina, and sintered at a temperature of $1500^{\circ}C$. Because of the relatively easy preparation of the test specimens and the high speed of testing, the Vickers indentation fracture (VIF) technique is more frequently used to evaluate the fracture toughness of biomaterials and hard biological tissues. The Young's modulus and hardness values were obtained by means of nanoindentation and indentation methods. The fracture toughness values of 3Y-TZP bioceramics were calculated and analyzed using 15 equations related to the VIF technique, and loadings of 49.03 and 196.13 N with a Vickers diamond. For validation, the results were compared with fracture toughness values obtained by the single-edge laser-notch beam (SELNB) method with an almost atomically sharp laser-machined initial notch.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.6
• /
• pp.596-602
• /
• 2006

The effects of resin additives and inorganic compounds addition on the thermal decomposition of low density polyethylene(LDPE) resin have been studied in a thermal analyzer(TGA, DSC) and a small batch reactor. The silica-alumina type compounds tested were kaolinite, bentonite, perlite, diatomaceous earth, activated clay and clay. The resin additives were antiforgging-agent and longevity-agent. As the results of TGA experiments, addition of antifogging-agent, longevity-agent and clay increased the temperature of the maximum reaction rate($T_{max}$). The silica-alumina type inorganic materials increased the pyrolysis reraction rate in the order of activated clay, diatomaceous earth, bentonite, perlites, and kaolinite. In the DSC experiments, addition of antifogging-agent and clay decreased the heat of fusion and the heat of pyrolysis reaction. Bentonite decreased 20% of the heat of fusion and 25% of the heat of pyrolysis reaction. In the batch system experiments, the mixing of clay retarded the initial producing rate of fuel oil, but increased the yield of fuel oil. Addition of bentonite increased the yield of fuel oil from LDPE resin. Mixing of antifogging-agent and longevity-agent produced the fuel oil having lower carbon number. The amounts of the carbon number below 12 in fuel oil decreased with adding the clay. That below 23 in fuel oil increased with mixing of bentonite, perlite, kaolinite, and activated clay. But the mixing of diatomaceous earth did not affect the carbon contents of fuel oil from pure LDPE resin. In the silica-alumina type inorganic material used in this experiments, bentonite was the most effective from the pyrolysis heat, yields, and the characteristics of fuel oil.