• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.133-142
• /
• 2018

Paper presents a comparative study of space vector pulse width modulation (SVPWM) switching sequences for Voltage Source Inverters (VSIs). Various SVPWM switching sequences are studied for two and three level VSIs in linear modulation index region. The computations of dwell times are presented for two and three level VSIs based on space vector geometry in a synchronized and optimized manner. The existing SVPWM switching sequences are implemented using Matlab / Simulink and in an experimental setup for three phase two and three level VSIs. The simulation and experimental waveforms of conventional SVPWM (CSVPWM) and bus clamped SVPWM (BCSVPWM) are demonstrated for two and three level inverter respectively. The performance of different SVPWM switching sequences are evaluated and presented based on weighted voltage total harmonic distortion (THD).

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.291-296
• /
• 2006

The restrictions concerning the use of the radio waves have become severe, the marine radar with low spurious is being developed. Therefore, it is necessary to develop aids to navigation as a radar beacon can respond to new type of marine radar. Because the system of radar in the future is an indetermination, new radar beacon should correspond to old and new radar system during a transition period. New radar beacon that is also able to respond to pulse radar, pulse compression radar and FM-CW radar were considered in these years in Japan. The sign of the response of Morse code in a new system is generated by the delay synthesis system. Computer simulation and actual examination using trial circuit were curried out. A big possibility was set up in the development of the new radar beacon that was able to correspond to old and new radar system. These results and the state of new radar beacon is mentioned in this paper.

• Journal of Communications and Networks
• /
• v.14 no.5
• /
• pp.518-523
• /
• 2012

This paper presents new coherent and non-coherent detection methods for the IEEE 802.15.4a low-rate ultra-wideband physical layer with forward error correction (FEC) coding techniques. The coherent detection method involving channel estimation is based on the correlation characteristics of the preamble signal. A coherent receiver uses novel iterated selective-rake (IT-SRAKE) to detect 2-bit data in a non-line-of-sight channel. The non-coherent detection method that does not involve channel estimation employs a 2-bit data detection scheme using modified transmitted reference pulse cluster (M-TRPC) methods. To compare the two schemes, we have designed an IT-SRAKE receiver and a MTRPC receiver using an IEEE 802.15.4a physical layer. Simulation results show the performance of IT-SRAKE is better than that of the M-TRPC by 3-9 dB.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.7
• /
• pp.668-679
• /
• 1990

The fully digitalized inveter has some difficulties in implementation because of the limitation of available memory capacity and computation time. This paper describes a new PWM(Pulse Width Modulation) Inverter technique which linearizes switching angle characteristics of SHEPWM(Selected Harmonic Eliminatin Pulse Width Modulation) Inverter. Also the detailed description of the scheme along with the realization is presented. The simulation and experimental results show that the proposed schemes have the advantates such as good voltage waveforms and memory-saving.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.12
• /
• pp.1230-1241
• /
• 1991

Asymmetrical pulse width modulated(APWM) control technique for AC chopper is proposed which can improve the input power factor. The ideal switching function for the proposed technique is derived and its optimal slope to maintain the input power factor to unity is calculated. By digital simulation several characteristics are investigated theoretically and then compared with those of the conventional PWM and the phase angle control technique. In order to maintain the input power factor to unity the optimal slope and the average value of the ideal switching function are calculated. The experimental results show a good agreement with the calculated ones, which proves the feasibility of the proposed technique.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1211-1213
• /
• 2004

CCFL(cold cathode fluorescent lamp) are used to backlight of LCD(liquid crystal display). CCFL dimming methods are used to pulse frequency modulation(PFM) or pulse width modulation(PWM). In this paper, design of CCFL driving and control circuit by half-bridge type series and parallel resonant inverter that variable frequency modulation method to control the output voltage current. Inverter switching frequency is higher than resonant frequency for stable operating, and it is possible dimming control. On the basis of equivalent circuit, the validity of this study is confirmed by the comparison of simulation and experimental result.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.2
• /
• pp.28-33
• /
• 2001

The subject of this study is to improve the position performance of the linear motion for hybrid type Linear Pulse Motor (HLPM). Generally, there are two applicable methods to ensure precise position control ; a good processing method. This paper is suggested an electrical 125 microstep driving method so as to achieves the excellent control performance, besides the small mechanical manufacture of teeth pitch. The compensation method of digital PI control is apply to step response of stable position control, step error, vibration suppression and the approach to high stability, and the Ziegler-Nichols tuning method is applied to the proper design of control parameter. The proposed control method has been verified by simulation results of the suitable gain and phase margin of bode plot, and from experiment result of step response.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2199-2201
• /
• 2005

High voltage power supply with pulse load($4.5{\mu}s$ and PRF 60Hz) condition is investigated which is of interest for applications like Klystron modulator power supplies with output voltage of 50kV. The performance specifications with this type of power supplies are very stringent demanding tight regulation(<0.01%) and high efficiency(> 85%). The solution to this problem as a single stage converter is very difficult. The final output voltage is obtained as sum of the output of SCPS & PCPS. The combination of the two stages can satisfy the pulse load specifications. The analysis of the voltage and power division between SCPS & PCPS has been done for the proposed topology. It has studied under various operating conditions of line and load. Simulation results are validated by experimental results.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.255-257
• /
• 2004

This paper was studied electromagnetic field distribution and damping of PD(Partial Discharge) signal in GIS(Gas Insulated Switchgear). Cut-off frequency of electromagnetic wave propagation modes were computed, electromagnetic field distribution of propagation modes in GIS by FEM(Finite Element Method) were simulated and simulated damping characteristic of electromagnetic waves in GIS by EMTP(Electromagnetic Transient Program) when generated PD pulse. Frequency band of $TE_{mn}/TM_{mn}$ modes were determinated by simulation results of electromagnetic field distribution and were discussed optimal position of UHF sensor from this results. Equivalent circuit was used to simulate signal damping of PD pulse in GIS by EMTP and compared with measured results in laboratory of KERI.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1954-1955
• /
• 2007

This paper presents a modeling method of speed controller for DC motor drive system by using the Embedded Target for TI C2000 DSP in MATLAB/SIMULINK. Speed controller is easily designed and implemented by using the MATLAB/SIMULINK program, and speed control response and stability of the DC motor can be improved. Feedback of motor speed is processed through C28x QEP(Quadrature Encoder Pulse) from encoder pulse. The controller is designed as PI speed controller. Simulation program is drawn using SIMULINK. Then a real-time program for speed control of the DC motor is downloaded into the eZdsp F2811 control board. Speed control response is verified through simulations and experiments.