• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.4
• /
• pp.750-756
• /
• 1997

The purpose of the study was to investigate a transmittance rate of UVB (Ultraviolet B) through summer fabrics and a protection rate of summer fabric from UVB. The subjects were randomly selected 159 fabrics from Korean common summer fabrics. The protection rates of 159 fabrics from UVB were measured by UVB lamp and UVB sensor, and 14 fabrics among these fabrics were selected for an assay of MTT(3-(4, 5-dimethylthiazol-2-yl) -2, 5 -diphenyltetrazolium). The protection rate of fabrics from cell toxicity of UVB was measured by investigating the difference of the amount of cell toxic substance on between fabrics covered with and without HeLa cell The average protection rate of 159 fabrics from UVB was 95.08%. As result findings, three negative correlations were found between: 1) the transmittance rate of UVB and the amount of MTT on fabrics (y=0.0373+0.O0518 x, r=-0.9323, p<0.001); 2) the air permeability of fabrics and the amount of MTT (r: -0.79, p< 0.01); 3) the air permeability of fabrics and the protection rate of fabrics from UVB (r=0.89, p<0.01). However, there was no effect of thickness of fabrics on the protection rate from UVB and the amount of MTT.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.385-387
• /
• 2008

When a fault occurs in the distribution system, it is detected by protection system, then protection system is opened and de-energises the feeder where the fault exists. in this paper, the failure rate of protection system will estimate that using a discrete markov approach with failure data of protection system in order to improve the reliability of protection system.

• Journal of the Korean Society of Radiology
• /
• v.11 no.4
• /
• pp.189-195
• /
• 2017

Radiation protection equipment has widely used to protect human body from radiations, for example X-ray and gamma ray. The material of the radiation protection equipment is mainly lead (Pb) which has brought out lead poisoning and pollution when the equipment is fallen into disuse. This problem makes research and development find new Pb-free materials for use of radiation protection. Manufacturing and evaluation processes for developing those material were carried out repletely until obtaining the performance of protection rate. In this study, combination possibility of shielding material was studied using Geant4 monte carlo simulation. X-ray tube under the same condition in the real measurement of the protection rate was simulated, and X-ray tube spectrum was obtained. The X-ray tube spectrum was applied to study on the protection rate and lead equivalent. The porosity effect was simulated, and was one of key factors to determine protection rate or lead equivalent in radiation protection sheet of Pb-free.

• Corrosion Science and Technology
• /
• v.14 no.5
• /
• pp.226-231
• /
• 2015

In spite of highly advanced paint coating techniques, corrosion damage of marine metal and alloys increase more and more due to inherent micro-cracks and porosities in coatings formed during the coating process. Furthermore, flowing seawater conditions promote the breakdown of the protective oxide of the materials introducing more oxygen into marine environments, leading to the acceleration of corrosion. Various corrosion protection methods are available to prevent steel from marine corrosion. Cathodic protection is one of the useful corrosion protection methods by which the potential of the corroded metal is intentionally lowered to an immune state having the advantage of providing additional protection barriers to steel exposed to aqueous corrosion or soil corrosion, in addition to the coating. In the present investigation, the effect of flow velocity was examined for the determination of the optimum corrosion protection current density in cathodic protection as well as the corrosion rate of the steel. It is demonstrated from the result that the material corrosion under dynamic flowing conditions seems more prone to corrosion than under static conditions.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.42 no.6
• /
• pp.1016-1024
• /
• 2018

Lifestyle of Health and Sustainability (LOHAS) influences the development of hygienic and health-oriented functional textile products; consequently, there has been an increase in the prospects for environmentally friendly natural dyeing products with functional and sensitive characteristics. Therefore, the present study expresses a functional manifestation on fabrics by treatment with chitosan and tannin using natural Coptidis Rhizoma. Cotton and wool fabrics dyed with Coptidis Rhizoma after treatment with chitosan and tannin. Consequently, the antibiosis of fabric dyed with Coptidis Rhizoma was excellent with 99.9% bacterial reduction for Staphylococcus aureus and Klebsiella pneumoniae in both fabrics. The deodorization rate was more than 90.0% in both fabrics after 120 minutes. The UV-A protection rate was 88.2% and the UV-B protection rate was 87.7% for cotton. The UV-A protection rate was 88.2% and the UV-B protection rate was 84.3% for wool fabric. Therefore, both of the dyed fabrics showed excellent UV protection by treatment with only chitosan and tannin, without mordants. Therefore, chitosan and tannin treatments were able to manifest functionalities in the fabrics dyed with Coptidis Rhizoma.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.1
• /
• pp.53-60
• /
• 1992

In this study, cathodic protection experiment was carried out by Al-alloy sacrificial anode in marine environments which have specific resistance($\rho$) if 25~7000$\Omega$.cm and investigated protection potential, current density and loss rate of Al-alloy sacrificial anode. The main results resistance($\rho$) of 400$\Omega$.cm, the cathodic protection potential appears high about-720 mV(SCE). But below specific resistance($\rho$) of 300$\Omega$.cm, the cathodic protection potential appears low about-770 mV(SCE) and simultaneously, cathode is protected sufficiently. 2) The loss rate of Al-Alloy sacrificial anode became large with decreasing specific resistance and increasing the ratio(A sub(c)/A sub(a) of bared surface area of anode and cathode. 3) The loss rate of Al-alloy sacrificial anode(w) to the mean current density of anode(i) is as follows. w=ai+b (a, b : experimental constants)

• Corrosion Science and Technology
• /
• v.8 no.4
• /
• pp.133-138
• /
• 2009

For the corrosion protection of the natural gas transmission pipelines, two methods are used, cathodic protection and coating technique. In the case of cathodic protection, defects are embrittled by occurring hydrogen at the crack tip or material surface. It is however very important to evaluate whether cracks in the embrittled area can grow or not, especially in weld metal. In this work, on the basis of elastic plastic fracture mechanics, we performed the CTOD testing with various test conditions, such as testing rate and potential. The CTOD of the base metal and the weld metal showed a strong dependence of the test conditions. The CTOD decreased with decreasing testing rate and with increasing cathodic potential. The morphology of the fracture surface showed the quasi-cleavage at low testing rate and cathodic overprotection. The low CTOD was caused by hydrogen embrittlement at crack tip.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.152-157
• /
• 2001

This paper was studied on the characteristics of crevice corrosion prevention of SS 400 in marine environment. In NaCl solution, polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 applied cathodic protection and non cathodic protection was measured according to the NaCl concentration. The main results obtained are as follows : The weight loss rate of Al-alloy galvanic anode was increased as the concentration of NaCl solution increased by 3.5% but the concentration increased over 3.5%, that of Al-alloy galvanic anode become decreased. The protective potential of SS 400 used Al-alloy galvanic anode becomes more cathodic polarization with increasing concentration of NaCl solution. Effects of oxygen on the weight loss rate of Al-alloy sacrificial anode for cathodic protection as the concentration of 3.5% NaCl solution become sensitive than that of 0% NaCl solution.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.1
• /
• pp.105-112
• /
• 2006

The main function of a reactor protection system is to maintain the reactor core integrity and the reactor coolant system pressure boundary. Generally, the reactor protection system adopts the 2-out-of-m redundant architecture to assure a reliable operation. This paper describes the safety assessment of a digital reactor protection system using the fault tree analysis technique. The fault tree technique can be expressed in terms of combinations of the basic event failures such as the random hardware failures, common cause failures, operator errors, and the fault tolerance mechanisms implemented in the reactor protection system. In this paper, a prediction method of the hardware failure rate is suggested for a digital reactor protection system, and applied to the reactor protection system being developed in Korea to identify design weak points from a safety point of view.

• Journal of radiological science and technology
• /
• v.42 no.5
• /
• pp.373-377
• /
• 2019

Radiation exposure is on the rise as the working hours of radiation workers increase. Accordingly, the importance of protection products for decreasing the dose of exposure has risen, and excellent X-ray shielding ability and light weight are required. The purpose of this study is to compare the Pb which use currently and other elements in order to reduce the exposure of workers to the most effective protection products. For experiment, we used the general X-ray equipment and angiography equipment, and obtained the Pb and apron's shielding rate. When the shielding rate of Pb and apron was compared in general X-ray equipment, the shielding rate was 95.1% for Pb 0.5 mm, 96.1% for apron 0.5 mmPb and 95.6% for Bi+W 0.5 mmPb. When compared the shielding rate of each aprons in angiography equipment, 0.5 mmPb apron was the highest as 96.4% and Bi+W 0.25 mmPb apron was the lowest as 90.2% at the 50 cm distance. The shielding rate of 0.5 mmPb apron was the highest as 95.7% and Bi+W 0.25 mmPb apron was the lowest as 85.9% at the 100 cm distance. As a result of evaluating the apron efficiency through this study, 0.5 mmPb apron showed the best shielding rate, but it was the heaviest apron. 0.35 mmPb apron and Bi+W 0.25 mmPb apron weighed light but had low shielding rate. Through the results of this experiment, it is recommended that radiation workers reduce radiation exposure by using more efficient protection products.