• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.42-48
• /
• 1999

A control method for a robot hand grasping a object in a partially unknown environment will be proposed, where a proximate sensor detecting the distance between the fingertip and object was used. Particularly, the finger joints were driven servo-pneumatically in this study. Based on the proximate sensor signal the finger motion controller could plan the grasping process divided in three phases ; fast aproach, slow transitional contact and contact force control. That is, the fingertip approached to the object with full speed, until the output signal of the proximate sensor began to change. Within the perating range of the proximate sensor, the finger joint was moved by a state-variable feedback position controller in order to obtain a smooth contact with the object. The contact force of fingertip was then controlled using the blocked-line pressure sensitivity of the flow control servovalve for finger joint control. In this way, the grasping impact could be reduced without reducing the object approaching speed. The performance of the proposed grasping method was experimentally compared with that of a open loop-controlled one.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.2
• /
• pp.106-115
• /
• 2002

The performance of an inverter-driven water-to-water heat pump with an electronic expansion valve (EEV) was measured as a function of compressor frequency, load conditions, and EEV opening. Based on the test results, a controller using proportional integral (PI) feedback or PI feedforward algorithm was designed and tested to investigate capacity modulation and transient response control of the system. Although the relation between superheat and EEV opening of the heat pump showed nonlinear characteristics, a control gain obtained at the rated frequency was applicable to various operating conditions without causing large deviations. When the simple PI feedback control algorithm was applied, a large overshoot of superheat and wet compression were observed due to time delay effects of compressor frequency. However, applying PI feedforward control scheme yielded better system performance and higher reliability, compared to the PI feedback algorithm.

• Journal of Drive and Control
• /
• v.10 no.3
• /
• pp.14-20
• /
• 2013

In the study, a control strategy using a feedback linearization compensator and a disturbance observer was suggested and applied to the synchronization control of two hydraulic cylinders. The hydraulic system consists of a proportional directional control valve with overlap characteristic near the neutral position, a conventional hydraulic cylinder and an external load. The control performances of the system were verified through numerical simulations. From the simulations, it was ascertained that excellent control performances were obtained with the suggested control strategy.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.25-32
• /
• 1994

A nonlinear control algorithm for the depth control of underwater vehicles is presented. In order to consider the deadzone effect of the flow control valve, a nonlinear fuzzy logic controller (FLC) is synthesized and combined with a linear proportional-derivative-acceleration (PDA) controller, which is called the PDA/FLC controller. And to show the effectiveness of the PDA/FLC control system, it is compared with the linear PDA control system through computer simulation. It is found that the PDA/FLC control system is suitable one to maintain the desirable depth of underwater vehicles with deadzone.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.369-378
• /
• 1999

This paper presents position control of an electro-hydraulic servo system whoch is operated by four 2-2way high speed on-off valves with either PWM PID control method or sliding mode control method, The advantages of using high speed on-off valves instead of electo-hydraulic servo valves or electro-hydraulic proportional valves are low price robustness for oil contamination and direct control without a D/A converter. The system consists of load cylinder inertia car potentiometer and external load cylinder. The experiments were carried out under several conditions and the results were compared. As a result the sliding mode method has shown good control performance and the robust and stable positioning of the elector-hydraulic servo system can be achieved accurately.

• Journal of Drive and Control
• /
• v.9 no.3
• /
• pp.1-7
• /
• 2012

This paper deals with the issue of model reference adaptive control strategy to control the injection molding machine. Prior to controller design, a pair of transfer functions are derived for the injection and dwelling process based on mathematical models of components. As external disturbances to examine the robustness of the proposed controller, nozzle clogging and contraction of molded objects are considered and realized by proportional valve. The overall simulation system, consisting of hydraulic components, controller and sensors, is implemented using the components of commercial software SimulationX. The simulation results confirm the proposed scheme's efficiency and robustness.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.11
• /
• pp.1061-1064
• /
• 2006

In this study, the performance of the tracking control of a pneumatic servo motor driven position control system using sliding mode is investigated. It is usually quite difficult to obtain precise tracking control of a pneumatic servo motor driven position control system because of the nonlinear deadband and stick-slip friction of the proportional valve. Therefore, a continuous sliding mode controller with velocity feedforward gain is proposed. Experimental results show that the tracking accurracy can be remarkably improved by adding a proper velocity feedforward term to continuous sliding mode controller.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.175-181
• /
• 2004

Analysis of brake characteristics has progressed rapidly in recent years, as computer techniques have developed. However, there are many problems in predicting braking characteristics, due to the numerous design variables of the brake system. Therefore, a synthetic braking performance analysis is required for all brake system parts such as master cylinder, booster, control valve and split system. In this paper, a program which can analyze braking performance such as force distribution, braking efficiency, pedal force and pedal travel, is presented. The preprocessor of the program helps users prepare input files through a dialog box. An additional postprocessor makes the graph presentation of solved results. Also, a simple example problem is applied to show the usefulness of the presented program.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.3 no.2
• /
• pp.7-13
• /
• 2006

In this paper the noise source and the amplifying mechanism are analyzed to reduce the noise of the excavator return line using the experimental approach and the CFD simulation. The result says that the reason of noise generation is pipe vibration caused by the cavitation at the main control valve and the level of noise is proportional to the valve back pressure at the return line. The methodology to reduce this noise was proposed and verified by the vehicle test.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.191-194
• /
• 1997

Passive, semi-active and active dampers have been used to dissipate energy in mechanical systems. Semi-active dampers have higher performance than passive dampers and require lower power to operate than active dampers. Its damping characteristics can be changed appropriately for varying conditions. In this paper, we developed a semi-active damper based on Magnetorheological(MR) fluid. MR fluid has a variable damping characteristics proportional for the magnetic field intensity. It has several advantages such as high strength, low viscosity, robustness in impurities and wide temperature range of operational stability. We designed a constrained rotary MR damper base on valve mode which can dissipate more energy per unit volume. The system with Bingham characteristics is obtained and proved by the experiment.