• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.6
• /
• pp.633-640
• /
• 2011

In this study, the stabilization of an edge flame and the intensity variation of a diffusion branch were investigated using a multi-slot combustor under conditions of high temperature and small fuel-concentration gradient (FCG). The combustor consists of three narrow channels: a quartz channel and two side-heating combustors. For the accuracy of this experimental study, quantitative analysis was carried out for each boundary condition. Stable edge flames could be observed under high-temperature conditions by controlling the FCG and fuel dilution ratio. Moreover, it was found that the intensity of the diffusion flame was increased by increasing the temperature of the mixture. On the contrary, the intensity of the diffusion flame was decreased by increasing the dilution ratio. It was also found that a propane flame is more sensitively affected by these experimental parameters than a methane flame.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.375-381
• /
• 2013

Kinetics data were obtained for steam reforming of methane and natural gas over the commercial nickel catalyst. Variables for the steam reforming were the reaction temperature and partial pressure of reactants. Parameters for the Power law rate model and the Langmuir-Hinshelwood model were obtained from the kinetic data. As a result of the reforming reaction using pure methane as a reactant, the reaction rate could be determined by the Power law rate model as well as the Langmuir-Hinshelwood model. In the case of methane in natural gas, however, the Langmuir-Hinshelwood model is much more suitable than the Power law rate model in terms of explaining methane reforming reaction. This behavior can be attributed to the competitive adsorption of methane, ethane, propane and butane in natural gas over the same catalyst sites.

• Journal of the Korean Chemical Society
• /
• v.48 no.2
• /
• pp.156-160
• /
• 2004

The extraction rates of plasticizer of LPG high pressure rubber are studied. Submerging solvents are composed of propane, n-butane, n-pentane, n-hexane, n-heptane, propylene, 1,3-butadiene, 1-pentene, 1-hexene, ethanethiol, t-butanethiol, dimethyl sulfide, methyl ethyl sulfide. The relationship between the extraction rate of plasticizer and the descriptors of submerging solvent by using multiple linear regression is as follows; PE(wt%) = 7.5193 - 0.58500Carbon${\sharp}$ + 2.3294DB + 2364SH, (N = 13, F = 24.135, R$^2$ = 0.8894, R$_{adj}^2$ = 0.8526, Variance = 7.588) Plasticizer is well extracted by LPG composed of the high vapour pressure and polarity compounds. The mass of extracted plasticizer becomes increasing in proportion to the contents of thiol sulfur compound and unsaturated hydrocarbon such as propylene and 1,3-butadiene in LPG. While the heavier hydrocarbons are, the less the quantities of plasticizer extracted from rubber are.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.22 no.1
• /
• pp.60-69
• /
• 1996

3-APPA는 생체내 물질 Υ-amino butyric acid와 유사한 구조를 갖는 물질로서 human fibroblasts 3-dimensional culture system 등의 in vitro 시험에서 collagen 합성촉진 효과, 세포증식 효과를 나타내며, hairless mouse를 이용한 동물시험에서도 collagen 합성이 증가되는 것으로 보고된 바 있다. 또한 피부 안정성에서도 우수한 결과를 보여줌으로서 화장품 분야에서 새로운 노화억제 물질로서 주목을 받게 되었다. 본 시험에서는 180명의 피검자를 대상으로 3개월간의 임상시험을 통하여 새로운 노화억제 물질인 3-APPA의 효능을 기존의 GABA 유사물질, aminopropane sulfonic acid와 비교하였다. 본 시험은 double-blind, randomized, vehicle-controlled clinical study로서 180명의 피검자를 APSA군, 3-APPA군, vehicle군으로 분류한 후 3개월간 매일 저녁 취침 전, 안면에 시험제품을 사용하도록 하였으며, 사용 전, 사용 1주후, 2주후, 6주후, 12주후 5회 설문지를 통하여 피부상태를 조사하였다. 각 설문내용은 피부 건조도, 피부 탄력도, 피부 주름량, 피부 윤기도, 피부 거칠기 정도에 대한 5개 질문으로 구성된 효능에 관한 질문과 흡수정도, 끈적임, 매끄러움, 보습력, 보습지속성, 전체적인 사용감에 대한 6개 질문으로 구성된 사용성에 관한 것이었다. 각 질문에 대하여는 매우 좋음 1점, 좋은 2점, 보통임 3점, 나쁨 4점, 매우 나쁨 5점 사이에서 답할 수 있도록 하였다. 시험 결과 APSA군은 6주와 12주후 피부 건조도, 피부 거칠기 항목에서 사용전에 비하여 유의한 차이를 나타내었다. 3-APPA군은 6주후 피부 건조도, 피부 거칠기, 피부 탄력도 항목에서 시료사용전에 비해 유의한 차이를 나타내었으며 12주후에는 피부 건조도, 피부 탄력도, 피부 윤기도, 피부 거칠기 항목에서 유의한 차이를 나타내었다. 12주후 APSA군은 피부 주름, 피부 탄력도 항목에서 vehicle 사용 피검자군에 비하여 유의적인 차이를 나타내었으나 3-APPA군은 피부 탄력도, 피부 주름량, 피부 윤기 항목에서 vehicle군에 비하여 유의적인 차이를 나타내었다. 결론적으로 3-APPA와 APSA 사이에 유의적인 차이가 있지는 않았으나 3-APPA군은 APSA군에 비하여 6주, 12주에서 사용전과 유의한 차이를 나타내는 항목이 많았으며 12주에서 vehicle과 유의적인 차이를 나타내는 항목도 많으므로 3-APPA가 APSA 보다 광범위한 피부노화 억제 효과를 갖는 물질이라고 할 수 있다.

• Journal of Sensor Science and Technology
• /
• v.27 no.4
• /
• pp.237-241
• /
• 2018

The real-time enrichment and detection of pathogens are serious issues and rapidly evolving field of research because of the ability of these pathogens to cause infectious diseases. In general, bacterial detection is accomplished by conventional colony counting or by polymerase chain reaction (PCR) after DNA extraction. As colony counting requires considerable time to cultivate, PCR is an attractive method for rapid detection. A small number of pathogens can cause diseases. Hence, a pretreatment process, such as enrichment is essential for detecting bacteria in an actual environment. Thus, in this study, we developed a microfluidic chip capable of performing rapid enrichment of bacteria and the extraction of their genes. A lectin, i.e., Concanavalin A (ConA), which shows binding affinity to the surface of most bacteria, was coated on the surface of magnetic particles to nonspecifically capture bacteria. It was subsequently concentrated through magnetic forces in a microfluidic channel. To lyse the captured bacteria, magnetic particles were irradiated by a wavelength of 532nm. The photo-thermal effect on the particles was sufficient for extracting DNA, which was consequently utilized for the identification of bacteria. Our device will help monitor the existence of bacteria in various environmental situations such as water, air, and soil.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.89-92
• /
• 2007

Partail oxidation(POX) of n-butane was investigated in this research by employing ceria-promoted Ni/calcium hydroxyapatite catalysts ($Ce_xNi_{2.5}Ca_{10}(OH)_2(PO_4)_6$ ; x = $0.1{\sim}0.3$) which had recently been reported to exhibit good catalytic performance in POX of methane and propane. The experiments were carried out with changing ceria content, $O_2/n-C_4H_{10}$ ratio and temperature. As the $O_2/n-C_4H_{10}$ feed ratio increased up to 2.75, n-$C_4H_{10}$ conversion and $H_2$ yield increased and the selectivity of methane and other hydrocarbons decreased. But with $O_2/n-C_4H_{10}$ = 3.0, $n-C_4H_{10}$ conversion and $H_2$ yield decreased. This is considered due to that too much oxygen may inhibit the reduction of Ni or induce the oxidation of Ni, which results in poor catalytic activity. The optimum $O_2/n-C_4H_{10}$ ratio lay between 2.50 and 2.75. $Ce_{0.1}Ni_{2.5}Ca_{10}(OH)_2(PO_4)_6$ showed the highest $n-C_4H_{10}$ conversion and $H-2$ yield on the whole. In durability tests, higher hydrogen yield and better catalyst stability were obtained with the $O_2/n-C_4H_{10}$ ratio of 2.75 than with the ratio of 2.5.

• Biomolecules & Therapeutics
• /
• v.19 no.2
• /
• pp.231-236
• /
• 2011

The aim of this study was to investigate the effect of charge carrier lipid on the skin penetration, retention, and hair growth of topically applied finasteride-containing liposomes. Finasteride-containing liposomes were prepared by traditional thin film hydration method using Phospholipon$^{(R)}$ 85 G and cholesterol with or without charge carrier lipid (1,2 dimyristoyl-sn-glycero-3-phosphate or 1,2-dioleoyl-trimethylammonium-propane for anionic and cationic charge, respectively). Freshly prepared finasteride-containing liposome suspension was applied on the hairless mouse skin, and skin penetration and retention were measured using Keshary-Chien diffusion cell. Non-liposomal formulation (ethanol 10% solution containing 0.5 mg/ml of FNS) was also used as a control. The amount of finasteride in the diffusion cell and mouse skin was measured by HPLC. The hair growth was evaluated using depilated male C57BL/6N mice. Mean particle size of all finasteride-containing liposomes was less than a micron, and polydispersity index revealed size homogeneity. Skin penetration and retention studies showed that significantly less amount of finasteride was penetrated when applied as anionic liposome while more amount of the drug was retained. Specifically, in liposome prepared with 10% anionic charge carrier lipid, penetration was 12.99 ${\mu}g/cm^2$ while retention was 79.23 ${\mu}g/cm^2$ after 24 h of application. In hair growth study, finasteride-containing anionic liposomes showed moderate efficacy, but the efficacy was not found when applied as cationic liposomes. In conclusion, topical application of finasteride using anionic liposome formulation appears to be useful option for the treatment of androgenetic alopecia to avoid systemic side effects of the drug.

• Biomolecules & Therapeutics
• /
• v.18 no.1
• /
• pp.99-105
• /
• 2010

The purpose of this study was to evaluate relative bioavailability of the coenzyme Q10 (CoQ10) in emulsion and three liposome formulations after a single oral administration (60 mg/kg) into rats. Emulsion formulation of CoQ10 was prepared by conventional method using Phospholipon 85G as an emulsifier, and three liposome formulations (neutral, anionic, and cationic) of CoQ10 were prepared by traditional lipid film hydration technique using Phospholipon 85G, cholesterol, and charge carrier lipids (1,2-dioleoyl-3-trimethylammonium-propane chloride salt for cationic liposome and 1,2-dimyristoyl-sn-glycero-3-phosphate monosodium salt for anionic liposome). Mean particle size of all CoQ10-loaded liposome was less than a micron, and size distribution of the liposome population was homogeneous. Bioavailability of CoQ10 in emulsion was 1.5 to 2.6-fold greater than liposome formulations in terms of $AUC_{0-24\;h}$. $T_{max}$ was 3 h when administered as emulsion while it was greater than 6 h in liposome formulations. Notably, it was approximately 8 h in cationic liposome. $C_{max}$ was highest in emulsion and was significantly decreased when administered as liposome. Charged liposome showed even lower $C_{max}$ than neutral liposome, especially in cationic liposome. In conclusion, therefore, it is suggested that clinicians and patients consider bioavailability issue a primary concern when choosing a CoQ10 product, especially when very high plasma level is required such as in the treatment of heart failure and Parkinson's disease.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.86-94
• /
• 2011

Pyrolytic lignin was obtained from biooil produced with yellow poplar wood. Fast pyrolysis was performed under various temperature ranges and residence times using fluidized bed type reactor. Several analytical methods were adopted to characterize the structure of pyrolytic lignin as well as the effect of pyrolysis temperature and residence time on the modification of the lignin. The yield of pyrolytic lignin increased as increasing pyrolysis temperature and decreasing residence time of pyrolysis products. The molecular weight of pyrolytic lignin determined by gel permeation chromatography (GPC) was approximately 1,200 mol/g, which was approximately a tenth of milled wood lignin (MWL) purified from the same woody biomass. Based on analytical data, demethoxylation and side chain cleavage reaction were dominantly occurred during fast pyrolysis.

• Journal of the Korean Ceramic Society
• /
• v.13 no.1
• /
• pp.25-29
• /
• 1976

The properties vary with quality of ferric-oxide that is major material of ferrites. In this point of view, a manufacturing method of pure and homogeneous fine ferric oxide is very important. The characters of this study are as follows: 1) Ferric oxide was made from waste pickling liquor of steel. 2) The crude ferric-oxide that is made by roasting the pickling liquor was dissolved in 20% HCI solution and then produced ferric chloride is purified by ethyl ether extraction. 3) The methanol solution of purified ferric chloride was sprayed into the refractory tube with compressed air and propane gas and then ignited leading to the ferric-oxide powder. 4) The produced oxide powder was introduced to the scrubber type vessel throught cooling system in order to collect the powder. 5) Crystalline phase of the powder was identified by X-ray diffraction and particle size, crystalline shape of the powder were investigated by settling method and electron microscope and the effects of concentration of ferric chloride in methanol on grain size were discussed. Results were obtained as fellows: 1) Total impurity in the ferric oxide produced from waste pickling liquor was 3.7%. 2) The solubilityof crude ferric oxide that was made from waste pickling liquor in HCI solution increased with the HCI concentration and reached to saturation range at 15% HCI concentration. 3) Extraction of FeCl3 increased with HCI concentration which is solvent. 4) Alpha ferric oxide obtained was very fine crystalline particles, the mean crystalline grain increased with the concentration of ferric chloride, and mean grain size distributed from 3.5$\mu$(at 0.5mole/l) to 0.5$\mu$(at 0.05mole/l).