• 디지털산업정보학회논문지
• /
• 제10권4호
• /
• pp.225-236
• /
• 2014

Productivity of public organizations was far older due to issue more difficult to measure than private organizations. Unlike the private sector, the public sector is a diverse and sometimes conflicting objectives (efficiency, effectiveness, equity, democracy, etc.) exist, it is difficult to measure productivity in a single index. Many departments of government is intricately interrelated and sometimes produced by the joint efforts, it is difficult to allocate performance, incentives and accountability to among departments. And there is the difficulty of collecting data on the productivity indicators of public organizations. Despite these difficulties, we developed a productivity index system and measuring method to systematically introduce the concept of productivity in the local administration. In this paper, the productivity and the productivity index measurement practices of local governments conducted annually from 2011 on was deep into research. First, the report found examples of the governments of the developed countries, productivity measurement, then the way MOPAS(Ministry of Public Administration and Security) measure productivity index of local governments, success factors, the implications were in-depth analysis. Finally, in order to enhance productivity and competitiveness municipalities studied ways to take advantage of the productivity index.

• 품질경영학회지
• /
• 제21권2호
• /
• pp.48-60
• /
• 1993

We have depended upon the quantitative analysis for productivity measurement. and excluded the qualitative analysis from productivity measurement. But I think that the qualitative analysis must be considered so as to get a effective productivity measurement This paper intened to establish improvement productivity measurement adopted quality cost of all the qualitative elements.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.281-282
• /
• 2012

Construction performance and productivity improvement are key focus areas in construction industry for any nation. There have been frequent delays and cost overruns in construction projects and poor productivity is one of the major contributions. For this reasons, there have been many research studies performed on the improvement of construction productivity for several decades. However, measuring productivity on a construction job site is still not an easy work. Because collecting reliable data consistently from the job site requires a lot of personnel efforts causing extra time and cost. This paper provides a basic study on the application of image processing technology for measuring unit productivity. It presented the possibility of unit productivity measurement by image processing technology through case study.

• 전기학회논문지
• /
• 제61권9호
• /
• pp.1330-1335
• /
• 2012

This paper proposes an automatic measurement sampling method for the semiconductor manufacturing process. The method recommends sampling rates using information of process capability indexes and production scheduling plan within the restricted metrology capacity. In addition, it automatically controls the measurement WIP (Work In Process) using measurement priority values to minimize the measurement risks and optimize the measurement capacity. The proposed sampling method minimizes measurement controls in the semiconductor manufacturing process and improves the fabrication productivity via reducing measurement TAT (Turn Around Time), while guaranteeing the level of process quality.

• 한국건설관리학회:학술대회논문집
• /
• 한국건설관리학회 2004년도 제5회 정기학술발표대회 논문집
• /
• pp.427-432
• /
• 2004

최근 건설시장의 경쟁이 치열해지고, 건설생산성을 향상시키는 것이 기업의 경쟁력 확보라는 인식이 높아짐에 따라 건설업에서도 생산성과 효율성에 대한 관심의 풍요도가 증대되고 있다. 본 연구에서는 기존의 생산성 측정 방식을 활용한 사례조사를 통해 생산성을 측정하고 측정된 내용에 근거하여 작업개선사항을 제시하였다. 제안된 개선사항은 시뮬레이션(simulation)기법을 동해 검증하였다. 본 논문의 의의는 생산성 측정을 분석하는데 있어 시뮬레이션 기법이 현장여건을 모두 고려한 최적의 대안은 아니지만 현장관리자로 하여금 상황에 적합한 최적의 작업방식을 선택하게하고 생산량을 예측할 수 있는 방법을 제시했다는 점에 있다.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.839-846
• /
• 2022

Traditionally, the construction industry has shown low labor productivity and productivity growth. To improve labor productivity, it must first be accurately measured. The existing method uses work-sampling techniques through observation of workers' activities at certain time intervals on site. However, a disadvantage of this method is that the results may differ depending on the observer's judgment and may be inaccurate in the case of a large number of missed scenarios. Therefore, this study proposes a model to automate labor productivity measurement by monitoring workers' actions using a deep learning-based pose estimation method. The results are expected to contribute to productivity improvement on construction sites.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.62-69
• /
• 2003

In most shipyards, the measurement of 3-dimensional relative position of pipes should be connected in the block depends on the manual operation. It results a very tedious and inefficient procedure, thus the proper measurement system is needed to improve productivity and accuracy. This paper describes the development of pipe measurement system including system concepts, measuring procedures, system calibration, and its accuracy and productivity. And also, the possibility and things to be improved for application in shipyard are discussed in this paper.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.141-142
• /
• 2012

Estimating the productivity of labor has relied on the experience and intuition of an estimator, or productivity data, such as standard in practical estimation. However, when new technologies and new construction methods employed in the construction industry, Dependence of a quantity surveyor's intuition is increased. This is because of the lack of a systematic methodology which models, estimates, and measures the labor productivity, Due to the historical productivity data is unavailable. Even thought project history data contains information that is important to predict the performance of a project, It can not provide valuable information to model, estimate, and measure the labor productivity. This is because 1) the absence of the productivity measurement system with consistency, 2) the difficulty of reusability of historical data collected. Therefor, this study suggests a methodology which build a productivity model by measuring the productivity of labor and collecting the historical data systematically. In addition, this methology is applied to develop a productivity model of shop-drawing and manufacturing process using descrete event simulation.

• 산업경영시스템학회지
• /
• 제17권30호
• /
• pp.81-87
• /
• 1994

Productivity relates output to input and also integrates performance aspects of quality, efficiency and effectiveness. Productivity improvement are associated with efficiency and effectiveness, productivity index involved quality and flexibility, integrated productivity measurement system, and other factors. This study focused on the productivity improvement that involved the opportunity costs such as qualify costs and flexibility effects.

• 한국공작기계학회논문집
• /
• 제18권1호
• /
• pp.83-89
• /
• 2009

In most multi-stage forging processes, the die spotting process or alignment of punch and die depends on the manual operation. It results a very tedious and inefficient procedure, thus the proper measurement system is needed to improve productivity and accuracy. This paper proposes a measurement system for alignment of die and punch which has a cylindrical holder, and describes the system concepts using 3 eddy-current displacement transducers and precise measurement jig. In order to apply this measurement system to real situations, the measuring procedures and system calibration method, etc. are proposed. Finally, the accuracy and productivity of this measurement system are investigated in this paper.