• Journal of Korean Society on Water Environment
• /
• v.28 no.6
• /
• pp.851-858
• /
• 2012

This study conducted a result analysis on operation of 26 Rural Community Sewage Treatment Plant (RCSTP) newly constructed in Yeong-yang, Bong-hwa and An-dong areas which are located at the upper region of An-dong Dam and Im-ha Dam. Based on operation result, an analysis on characteristics of sewage in each area and the treatment efficiency of the installed treatment process was conducted. The result of analysis on characteristics of sewage has shown the difference in concentration of the sewage according to area characteristics. Sewage in areas with frequent occurrence of agricultural water and livestock wastewater had high concentration. It is important to select the most suitable treatment process when selecting a treatment process for RCSTP according to properties of sewage in each area. As a result of operation, the disposal efficiency for organic matter and suspended solids was stable with less fluctuation, but the disposal efficiency for nitrogen and phosphorus showed high fluctuation. This signifies that it is necessary to pay attention to operation condition management of nitrogen and phosphorus when operating RCSTP.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.177-184
• /
• 2014

PURPOSE. The aim of this study was to measure the changes on the marginal and internal adaptation of zirconia based anterior fixed partial dentures after the porcelain firing process. MATERIALS AND METHODS. A total of 34 anterior fixed partial dentures using LAVA CAD/CAM system (3M ESPE, Germany) were applied. Two silicone replicas were obtained: one is obtained before porcelain firing process (initial) and the other is obtained after porcelain firing process (final), followed by the examination under a binocular stereomicroscope. Kruskal Wallis and Wilcoxon Signed Ranks tests were used for the statistical analysis (P<.05). RESULTS. No statistically significant difference was found between initial and final marginal gap values (P>.05). At the internal gap measurements, final marginal area values ($59.54{\mu}m$) were significantly lower than the initial marginal area values ($68.68{\mu}m$)(P<.05). The highest and the lowest internal gap values were observed at the incisal/occlusal area and at the marginal area, respectively. In addition, lower internal gap values were obtained for canines than for central incisors, lateral incisors and premolars at the incisal area (P<.05). CONCLUSION. The firing cycles did not affect the marginal gap of Lava CAD/CAM system, but it is controversial for the internal gap.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2020.06a
• /
• pp.201-201
• /
• 2020

• Journal of Wetlands Research
• /
• v.15 no.4
• /
• pp.453-460
• /
• 2013

Rural area sewage distribution rate is 40 % less than urban area. Previous research results announced that one of the reason in water resource pollution was caused of low rural area sewage distribution rate. Analysis on operation result of 11 RCSTP in Bong-hwa area which is located at the upper region of An-dong Dam and Im-ha Dam. Based on operation result, an analysis on characteristics of wastewater in Bong-hwa and treatment efficiency of installed treatment process was conducted. The wastewater influent of Bong-hwa contained high organic matter and nutrient than those of urban area. Treatment process showed totally stable treatment efficiency. But, The treatment efficiency for nutrient showed high fluctuation. This result means which is need to operation condition control of nutrient treatment when operating RCSTP.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.4 no.1
• /
• pp.36-40
• /
• 1999

Optimal lyophilization process was developed for manufacturing the dried product of Lactobacillus acidophilus with high cell viability. Three major factors, freezing rate, specific surface area of samples, and stabilizer type and their synergy were shown to play a crucial role in the development of an effective lyophilization process. Finally we found an optimal combination among three process parameters mentioned above; an exceptionally high cell survival percentage of 90% was achieved using the 8.28 cm-1 specific surface area of samples, slow freezing rate, and a stabilizer composition of 4% skim milk +1% glycerol +0.1% calcium chloride.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.33-36
• /
• 2001

Chemical mechanical polishing(CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for deep sub-micron technology. The rise throughput and the stability in the device fabrication can be obtained by applying of CMP process to STI structure in 0.18$\mu\textrm{m}$ m semiconductor device. The reverse moat process has been added to employ in of each thin films in STI-CMP was not equal, hence the devices must to be effected, that is, the damage was occurred in the device area for the case of excessive CMP process and the nitride film was remained on the device area for the case of insufficient CMP process, and than, these defects affect the device characteristics. Also, we studied the High Selectivity Slurry(HSS) to perform global planarization without reverse moat step.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.57-65
• /
• 1997

In this study, a cutting force in the Ball-end milling process is calculated using Z-map. Z-map can describe any type of cutting area resulting from the previous cutting geometry and cutting condition. Cutting edge of a ball-end mill is divided into infinitesimal cutting edge elements and the position of the ele- ment is projected to the cutter plane normal to the Z axis. Also the cutting area in the cutter plane is obtained by using the Z-map. Comparing this projected position with cutting area, it can be determined whether it engages in the cutting. The cutting force can be calculated by numerical integration of cutting force acting on the engaged cutting edge elements. A series of experiments such as contouring and upward/downward ramp cutting was performed to verify the calculated cutting force.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.985-988
• /
• 1997

In end milling process, the undeformed chip section area and cutting forces vary periodically with phase change of the tool. However the real undeformed chip section area deviates from the geometrically ideal one owing to cutter runout and tool shape error. In this study ,a method of estimating the real undeformed chip section area which reflects cutter runout and tool shape error was presented in up end milling process using measured cutting forces. Size effect was identified from the analysis of specific cutting resistance obtained by using the modified undeformed chip section area.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.24-29
• /
• 2002

In any rapid prototyping process, the layer by layer building process introduces an area error between the staircase and the surface line specified by the computer-aided design model. This affects the dimensional accuracy as well as the surface finish for different part build orientations. This paper describes a methodology for computing the area error for any orientation of the part built by the fused deposition modelling system. This technique can be applied to determine the best build orientation of the part, based on the minimum area error. This technique is verified by comparing the results with the experimental measurements of the area error of the parts built at different orientations.

• Journal of Korean Society of Rural Planning
• /
• v.18 no.3
• /
• pp.175-186
• /
• 2012

This is a study of a residential area for displaced villagers planned for residents of Gyodo Village who must evacuate their hometown because of flooding due to the Hantan River Dam Project. The study aims to construct a plan for a new residential area for the villagers focusing on reflecting the existing characteristics of their former village and on ensuring sustainability for the new village. Departing from previous practice of focusing on merely physical aspects when planning, the current study is significant in that it presents a new planning process and method for a sustainability-focused plan. While the study has many limitations such as objectivity in the process of deriving the sustainability indicators and the appropriateness of the indicator questions, it is hoped that future studies on sustainability will serve to make up for these limitations and problems.