• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.10
• /
• pp.438-442
• /
• 2005

Si nanocrystal (Si NC) memory device has several advantages such as better retention, lower operating voltage, reduced punch-through and consequently a smaller cell area, suppressed leakage current. However, the physical and electrical reasons for this behavior are not completely understood but could be related to interface states of Si NCs. In order to find out this effect, we characterized electrical properties of Si NCs embedded in a SiO$_{2}$ layer by scanning probe microscopy (SPM). The Si NCs were generated by the laser ablation method with compressed Si powder and followed by a sharpening oxidation. In this step Si NCs are capped with a thin oxide layer with the thickness of 1$\~$2 nm for isolation and the size control. The size of 51 NCs is in the range of 10$\~$50 m and the density around 10$^{11}$/cm$^{2}$ It also affects the interface states of Si NCs, resulting in the change of electrical properties. Using a conducting tip, the charge was injected directly into each Si NC, and the image contrast change and dC/dV curve shift due to the trapped charges were monitored. The results were compared with C-V characteristics of the conventional MOS capacitor structure.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.2
• /
• pp.107-112
• /
• 1997

본 연구는 자유표면 인삭을 위한 실험 기법 개발에 관한 연구이다. 2차원 수중익에 의해 발생되는 자유표면파를 연구대상으로 삼았다. 실험은 회류수조에서 행하였다. NACA 0012 수중익을 여러가지 길이와 2가지양각에 대해서 실험한 결과 생기는 비선형 자유표면 파를 인식할 수 있도록 영상처리 기술을 도입하였다. 실헙결과 얻은 자유표면 형상을 다른 연구자의 결과와 비교하였다. 비교결과 영상처리의 기법이 자유표면을 인식하는데 대단히 유용한 도구임을 알 수 있었다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.04a
• /
• pp.463-465
• /
• 2004

베디드 시스템의 발전으로 인하여 고성능화, 소형화, 편의성 등이 강조되어 지는 시점에서 의료장비 또한 임베디드 시스템 기술 도입이 빠르게 진행되어 지고 있다. 본 논문에서는 초음파 영상진단 단말기 (Magic-Probe)를 구현하기 위해 SA-1100 마이크로 프로세스 레퍼런스 보드에 리눅스 커널을 포팅하고 포팅된 플랫폼을 기반으로 초음파 영상진단을 처리하기 위한 응용프로그램의 설계 및 구현에 관하여 논하도록 하겠다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1121-1127
• /
• 2000

Among many EMI suppression techniques for radiated emissions from PCB traces, image technique is adapted in this paper. A model for the analysis of the effect of image plane on the radiation of a microstrip trace is presented. After a simulation was carried out by using the FEM(Finite Element Method), field strength was measured with electric probe. The radiated emission levels were measured for various image plane width, separation distances, and their results show that the measured data are very close to those of simulation result. It proves that a proper use of image planes on the PCBs is very effective means of reducing EMI emissions on the PCBs.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.4
• /
• pp.173-177
• /
• 2007

A photo-reactive methacrylate monomer having triazine as a core component was examined for photochromic diffractive image formation. Photochromic photopolymer films as a recording media contained a monomer mixture of triazine difunctional metharylate (DT) and ethylene glycol phenyl ether acrylate, binder polymer, photo initiator, and a photochromic spiro-oxazine dye. The content of photochromic dye was changed to examine the effect of photochromophore on diffraction efficiency and real holographic image formation. Holographic recording was performed on the photopolymer film by the combination of reference and probe beam. The diffraction efficiency of the photopolymer film in real-time measurement reached a maximum of $\sim90%$ within 30s. It was highly dependent on the photochromophore contents. After holographic recording, the color of the recorded area was changed under UV light (365 nm) and reversibly bleached to original color upon exposure to a visible light source. Films containing only photochromophore without monomer mixture were not reactive under the recording beam (491nm). Diffractive image formation and mechanism of the holographic recording in the presence of photochromophore will be presented.

• Corrosion Science and Technology
• /
• v.20 no.3
• /
• pp.118-128
• /
• 2021

The oxide layer in samples taken from an irradiated Zr-2.5Nb pressure tube from a CANDU-PHWR reactor was analyzed using electron probe microanalysis (EPMA). The examined tube had been exposed to temperatures ranging from 264 to 306 ℃ and a neutron fluence of 8.9 × 10²¹ n/cm² (E > 1 MeV) for the maximum 10 effective full-power years in a nuclear power plant. Measuring oxide layer thickness generally employs optical microscopy. However, in this study, analysis of the oxide layer from the irradiated pressure tube components was undertaken through X-ray image mapping obtained using EPMA. The oxide layer characteristics were analyzed by X-ray image mapping with 256 × 256 pixels using EPMA. In addition, the slope of the oxide layer was measured for each location. A particular advantage of this study was that backscattered electrons and X-ray image mapping were obtained at a magnification of 9,000 when 20 kV volts and 30 uA of current were applied to radiation-shielded EPMA. The results of this study should usefully contribute to the study of the oxide layer properties of various types of metallic materials irradiated by high radiation in nuclear power plants.

• Journal of the Korean Society of Radiology
• /
• v.11 no.7
• /
• pp.571-578
• /
• 2017

Bubbles are generated by the boiling of the cooling water when an accident occurs in the reactor and then in order to measure the void fraction, the Optical Fiber Probe(OFP) and optical camera are used in thermal hydraulic safety research. However, such an optical method is not suitable for measuring the void fraction in a $17{\times}17$ array of fuel rods due to the geometrical limitations. This study was conducted as a preliminary study using x-ray system and various phantoms before applying to rod bundles. Through radiographic and tomographic experiments, the tube voltage of the x-ray generator was 130 kVp and the tube current was 1 mA. In addition, it is possible to measure the hole of 1mm in size visually through the bubble resolution phantom, and it is confirmed that the contrast is relatively decreased in the inside of the freon in the case of the contrast evaluation using the road phantom. However, we could obtain good image without distortion when reconstructing the image. Bubble generation phantom experiments were used to confirm the flow direction of the bubbles and to acquire tomography images. The image J tool was used to measure the void fraction of 18 % for a single tomography image. This study has carried out previous researches for the measurement of the bubble rate around the nuclear fuel and could be used as a basic research for continuous research.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.96.5-96
• /
• 2002

This paper describes extraction procedures for the center coordinates of steam generator tubes of Youngkwang nuclear power plant No. 6 unit. The centering coordinates of tubes are needed for monitoring whether ECT probe is exactly inserted into tube or not. However, The tube image tends to have poor contrast because steam generator bowl is sealed. The centering coordinates extraction procedure consists of two steps. The first step is to process the region with high contrast in entire image of steam generator tubes. Using the center points extracted in the first step and the geometry of tubes lined up in regular triangle patterns the centering coordinates of the rest region with low contrast...

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1104-1113
• /
• 2000

This paper proposes an efficient reverse engineering technique for compound surfaces using a boundary detection method. This approach consists in extracting geometric edge information using a vision system, which can be used in order to drastically reduce geometric errors in the vicinity of compound surface boundaries. Through the image-processing technique and the interpolation process, boundaries are reconstructed by either analytic curves (e. g. circle, ellipse, line) or parametric curves (B-spline curve). In other regions, except boundaries, geometric data are acquired on CMM as points inspected using a touch type probe, and then they are interpolated on several surfaces using a B-spline skinning method. Finally, the boundary edge and the skinned surfaces are combined to reconstruct the final compound surface. Through simulations and experimental works, the effectiveness of the proposed method is confirmed.

• Korean Journal of Optics and Photonics
• /
• v.23 no.4
• /
• pp.135-142
• /
• 2012

We have developed a measurement method of the refractive index profile of an optical fiber by using diffraction phase microscopy. In the microscope system, the reference light was extracted directly from the probe light that passed through the sample by means of pinhole filtering with a diffraction grating. The spatial interference pattern produced by the probe light and the reference light was processed to generate the phase image of the sample fiber. The index profile was obtained by the inverse Abel transform of the phase profile. In order to remove the background phase that originated from the index difference between the cladding and the surrounding medium, the background phase was calculated from the phase data of the cladding to make a core phase profile that can be directly transformed to the index profile of the core without the full phase image that includes the entire cladding part.