• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.5
• /
• pp.825-830
• /
• 2016

The purpose of this study optimizes the conditions of PLA printing material for 3D printer. Deltabot type 3D printer is used. The ranges of printing temperature, printing speed, and infill density are $195{\sim}215^{\circ}C$, 10~70mm/sec, and 10~100% respectively. From the results of printing temperature, printing quality is almost same every printing temperature. From the results of printing speed and infill density, printing quality is excellent under 40mm/sec, and over 50% respectively. Surface roughness is $2.28{\mu}mRa$ at $205^{\circ}C$, 10mm/sec, 100%, and is $5.93{\mu}mRa$ at $205^{\circ}C$, 70mm/sec. Surface roughness is directly proportional to the printing speed, and is inversely proportional to the infill density. Objects fabricated PLA printing material adhere bed at room temperature.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.2
• /
• pp.55-60
• /
• 2010

Ink transfer process from the printing roll to the moving web was investigated using a CFD technique for the application in R2R printed electronics. In line with the requirement that the web handling speed needs to be increased further for the cost competitiveness, the effects of web moving velocity with relatively complex roll patterns were analyzed. To make the present analysis more realistic, the numerical geometry and the ink properties were selected to match those of the real printing production system. Our numerical results showed that both web handling speed and complex printing-roll patterns influenced the shape of the transferred ink. As the web moving speed approaches towards 30mpm, a significant distortion of the shape of the transferred ink occurred. In the range of pattern width smaller than 100 microns, a phase distortion was also found to occur in all the printing-roll patterns considered in the present work but the ratio of the phase distortion to the line width gets smaller as the width becomes smaller. Thus, the web handling speed and the shape of printing-roll pattern will be important elements for the better printing quality under 100 micron line width range.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.910-913
• /
• 2009

This paper examines attaching speed, detaching speed and contact time which affected in the ink transfer ratio and presents the best conditions for fabrication process of electrodes with Ag-ink using microcontact printing method. In conclusion, it shows the best printing characteristic by two conditions. One of condition is the attaching speed have to within less than 1mm/s and the detaching speed is high velocity as 1000mm/s and the contact time is taken about the minimum time when inking process. Another condition is the attaching speed have to within more than 100mm/s and the detaching speed have to within less than 1mm/s and the contact time is longer than 30second when the printing process. As using these condition and the stamp sized 5cm${\times}$5cm, it was possible for printing equally until $30{\mu}m$ of width. The printed thickness of a electrode was about 300 to 500 nm, the surface roughness was about dozens nm under 50 nm.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.873-878
• /
• 2007

Stability of high-speed roll-to-roll printing machines is one of the most important factors that are required for the printing machines to operate properly and to obtain reasonable printing performance. This paper proposes a new model for the web-tension system of a high-speed gravure printing machine considering span-length variations due to dancer rollers, and analyzes the stability of plant dynamics of the printing machine using the proposed model. Span-length variations due to dancer motions are considered for the modeling of plant dynamics in two ways; one is to include the effect of span-length variations without considering dancer inertias and viscous frictions, and the other is to include the effect of span-length variations with considering dancer inertias and viscous frictions. The stability of the plant model is analyzed for various web-speeds using the eigenvalues of the linearized model about operating points.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.1
• /
• pp.75-83
• /
• 2011

As screen printing is changed by automation recently, could print more exactly. However, must suffer great many trial and error to have still gotten perfect result. By the way, at this step, fair time and money should be invested. Therefore, if search for optimum condition in early time visualizing screen printing process using simulator program before progress printing, is judged that may be correct and gets printing result efficiently. In this paper, searched optimum printing speed and ink viscosity using FLOW-3D program. Also, the result could confirm truth that is agreeing almost with experiment contents. Through this, is thought that may expect extension of screen printing wide application that vivify advantage of screen print if use simulation program.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.344-349
• /
• 2014

$RuO_2$-based high frequency thick-film resistor paste was printed at the speed of 10, 100, 300 mm/sec on the AlN substrate, and then sintered at between 750 and $900^{\circ}C$. The sintered thick films were characterized in terms of printing and sintering conditions. With increasing printing speed, the thickness and roughness of sintered film increased. The resistance of the thick film resistor was reduced by increasing the printing speed from 10 to 100 mm/sec, but did not significantly change at 300 mm/sec speed. With increasing sintering temperature, the surface roughness and thickness of sintered resistor film decreased. The reduction rate was large in case of fast printed resistor. The resistance of the resistor increased up to $800^{\circ}C$ with sintering temperature, but again decreased at the higher sintering temperature.

• Transactions of Materials Processing
• /
• v.31 no.2
• /
• pp.89-95
• /
• 2022

3D printing products manufactured by material extrusion are used in many industrial fields recently. However, these products are difficult to use in the field due to their low tensile strengths. In order to solve this problem, research on improving the tensile strength of the output using a 3D printer has been continuously conducted. In this study, we performed a tensile test using Universal Testing Machine according to infill pattern, nozzle temperature, bed temperature, and printing speed conditions. Results revealed that tensile specimen of concentric shape had the highest tensile strength in infill pattern condition and that the tensile strength increased linearly with increasing nozzle and bed temperatures. However, the tensile strength decreased with increasing printing speed. Consequently, we confirmed that tensile strength could be increased and decreased depending on output conditions of 3D printing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.75-76
• /
• 2010

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.126-126
• /
• 2012

In past decades, the themal inkjet (TIJ) printer has been widely used as one of the most well-known digital printing technology due to its low cost, and high printing quality. Since the printing speed of TIJ printers are much slower than that of laser printers, however, there has been intensive efforts to raise the printing speed of TIJ printers. One of the most plausible methods to raise the printing speed of TIJ printers is to adopt a page-wide array TIJ printhead. To accomplish this goal, the high efficiency inkjet heating resistor films should be developed to settle the high power consumption problem of a page-wide array TIJ printhead. In this study, we investigated noble metal based multicomponent thin film resistor films prepared by atomic layer deposition (ALD) for a high efficiency inkjet printhead. Design concept, preparation, material properties of noble metal based multicomponent thin films will be discussed in terms of mutlfunctionality.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.22-24
• /
• 2004

This paper proposes a printing quality inspection system of film-type envelopment. Since the printing system is running at very high-speed (140m/min.) and the line error has very narrow width, we have to choose one-dimensional high-speed and high-resolution line scan camera. The vibration of the printing machine and the illumination environment make the inspection problem more harder. To obtain reliable inspection results, many software image processing techniques are applied and many parameters are tuned. The performance of the proposed system is proved by many simulations and long time real-plant experiments.